I migrated from AC3D 2010 32-byte to AC3D 2012 64-byte recently. When I migrate my projects to 2012 and open the old 2010 drawings in 2012 I lose the surface lines out of my section sets. It doesn't seem to bother the profile views, only the section views.
Is there a way to work around this problem w/o having to regenerate the section views?
How can the cross sections be setup to label the existing and proposed grade at the centerline of a cross section, see attached. Could do this in LD but have not been able to figure it out in Civil 3D
C3D 2013 (latest updates), 2014 Infrastructure Design Suite
Win 7 Pro, 64-bit
16 GB RAM
While I was out, my partner somehow now has two existing ground lines in my cross-sections. ####exist and ####exist (1). They are offset by about .5 feet left to right. Where do I remove the surtface ###exst (1) from the cross sections. I am looking now.
View 2 Replies View RelatedI've worked with LDD for 11 yrs. Last week the IT guys changed my PC to Windows 7 64bit, so I can't have LDD and I have to work with C3D. so I am following software tutorials.
for designing a road I created:
alignment ---> surface profile ---> layout profile (project line) ---> assembly ---> subassemblies ---> corridor ---> set target surface and frequencies
Corridor is created with daylights ,but I don't see existing ground in corridor section editor.
There is nothing about this in tutorial. Also I don't know how to calculate the volumes, in LDD after this stage we could calculate the volumes. i think in C3D I should do more for calculation.
I have to migrate from a windows pc to a mac. I have already installed Lightroom 4.4 on the new mac book pro. How can I manage the migration without loosing all my Catalogs, photos, templates, and all the work done on my photos with Lightroom? Which files do I have to paste and copy in my new mac? Do I have to do some other operations before (backup or other?)
View 1 Replies View RelatedHaving issues with where the first section view starts when trying to place multiple section views on sheets. The problem I am having is that the offset from the bottom of the sheet frame seems to be a half unit off and grid lines will not line up with the sheet gridlines we have developed. I attached a pdf of the resulting offset. what I need to look for to adjust the bottom offset?
View 2 Replies View RelatedIn 2011 the pipe network cross section labels had to be exploded or they would disappear once you closed the drawing (even with saving).
In 2012 can you close and open a drawing and have the labels not disappear?
Civil 3D 2012 SP4.0 Windows 7 Enterprise 64-bit
C3D 2014 SP1
Dell M6600, Core i7 @ 2.3GHz, 16 GB ram
Dell T3500 workstation, too much ram to post
Any new methods for depicting flared end sections in profile views in Civil 3D 2013 or 2012? I just loaded Civil 3D 2013 last week and have been checking to see if flared end section depiction in profile views is any better than previous versions. I haven't noticed anything different. I'm I the only one wanting a easier way to depict flared end sections in profiles? In short, I have never been able to figure it out.
View 1 Replies View RelatedI have my surface, aligment and sample lines created, but I cant get my sample lines profiles.
The grid apperas without data, it is like I have never selected a surface, but I did !
This is what I get , totally empty
I am manually editing my section geometry by moving the grips and am wanting to remove some of the additional vertices that I don't need in a certain area. How to delete extra points? I can't seem to find a way to do this either graphically or in the Section Editor. I am using C3D 2010.
View 4 Replies View RelatedI have created an existing ground surface...also 2 surfaces from corridors...one a road and 2 a berm. How do I merge these and get final contours of the proposed site after construction?
View 0 Replies View RelatedBecause there is a PI in my alignment, the section lines in my corridor are overlapping creating problems with the surface. Is there anything that I can do in this situation?
View 6 Replies View RelatedAm getting these lines on my crossection when I plot my crosssection sheets. they don appear when I preview. they only appear after printing. I really need to print these crosssections for submission.
Am using civil 3d 2013 update 2.1
Civil 3D 2013 64bit SP1
Elitebook 8540w
Core i7 2.8GHz, 8Gig RAM
NVIDIA Quadro FX880
160Gb SSD
Often we build a design surface from feature lines and possibly a grading or two. Then we cut sections.
Now, for set out, and especially for smaller contractors who don't have fancy survey gear, it would be really nice to be able to show design surface levels in section bands BUT ONLY AT THE SURFACE-DEFINING FEATURE LINE LOCATIONS.
I am aware that we can use grade breaks...but this gives us band data at each triangle intercept which is too much data. We can weed this data, but that is indiscriminate and I really need only the data at the surface-defining geometry points (feature line locations.)
We can also use station/elevation labels on the section views but this is time-consuming and non-dynamic. Band labels are dynamic and more or less automatic...if only we could get the discrete locations we need labelled.
I'm having a random issue with the daylight ties lopes not tieing to the EG surface at all stations in the Corridor Section Editor. Some stations daylight fine. In plan view the daylight lines vary left & right as expected but don't display at all in Section Editor.
Some background info:2012 Civil 3D SP1 / 64 bit / WIN7Simple corridor used1 alignmentSame fg profileSame drefd EG surface (set all targets for daylight LT/RT)Only one assembly applied to entire corridor Attached are 2 captions of the issue I'm having which each have a cut & fill occurrence as well as a caption of the entire align. & corridor. I did try deleting corridor & recreating and even recreated a simpler assembly and still have the daylight issue in same areas of corridor.
I'm uploading the .dwg and .txt files. I'm trying to get volume calcs cut and fill between two surfaces and when I compare the data between AGTEK's Highway 3D there is different results. I looked into it to find these random line appearing in Autocad making what seems to be the problem. Where are these coming from and how do I fix? Also, if you could anwser how can I insert a sectional following the 12'-23' offsets and dropping 1.16' down and adding it to my design surface. I want to make a big box there added to design surface.
View 1 Replies View RelatedI created sample lines and section views for my road projects. I set all line works to appropriate layers except for "Segment and Points". Cannot change from layer "0".
I right click the existing grade on my section views, click "edit section style", click "display", then change the layer of Segments and points and click "OK", "apply".
Go back to my drawing, verify the layer but still layer "0". I tried so many times, read the manual, call friends but no luck. I am tempted to "explode" my drawing.
How do I change the grid lines from solid to a dotted line in the Section View?
View 3 Replies View Relatedrecommend a good way to indicate the location of cross section sample lines in a profile view (of same alignment) as vertical lines? the sample lines have been created at user defined locations from polylines, and do not follow a particular station order. my first thought was to use transparent command to draw line in profile view using station from plan view, but i have in excess of 100 cross sections, and that may be time consuming.
Civil 3D 2013 SP1, Win 7-64 bit
12GB RAM
I have spent most of today working on a project for work, and here I am at the end of the day going back to glance over everything when I realize that about 75% of the work I did on one of the files didn't save. I suspected I was having this problem before, so I had been meticulously saving after every edit and making sure to wait for the hourglass to go away before continuing.
View 3 Replies View Relatedwe are planning to migrate from windows xp to windows 7 64 bit. Is there are chance to deploy a migration script to backup the user settings from xp and import them to windows 7. Copying the files from %appdata% is not a good solution because if the program was never started before the Autocad product will start a repair for user settings and so the files and settings are deleted.
I need a method for more than 100 pcs so using the implemented export and import tool is not possible.
Is there any way to stop the flipping of the solid/sketch view from iso to normal?
its annoying to make changes to a sketch and constantly have to re orient the part after finishing a sketch, I dont want the solid model to return to iso view after sketching, is there a setting for this?
I have just upgraded from C3D 2011 to C3D 2013. I know it should be simple to copy my custom CUI file from one release to another, but somehow I'm missing it. In 2013, I open Workspace/Customize, then swith to the Transfer tab (right sofar?). In the pull down, I choose Open. Now at this point, I think I should just browse for my 2011 CUI file, but for some reason, I can't find it. If I search my C drive, I still can't find it. With 2011 open, in Workspace, the name of the CUI that I use is "Randy", so I'm assuming the file name to search for would be randy.cui.
View 5 Replies View RelatedI would like to express my dismay at hearing that exchange content is being migrated to "social networks". While I have no problem with this, per se, this will restrict access for the majority of users who cannot access Twitter, Facebook and Youtube at work which is when they are likely to need the content most.
As a matter of interest how many of you have access to these networks at work (from your laptop/PC not via smartphones, tablet devices etc).
IDSP Premium 2014 (mainly Civil 3D 2014 UKIE SP1 & Infraworks with some limited 3ds Max Design)
Win 7 Pro x64, 256Gb SSD, 300Gb 15,000 rpm HDD
16Gb Ram Intel Xeon CPU E5-1607 0 @ 3.00GHz (4 CPUs), ~3.0GHz
NVIDIA Quadro 4000, Dual 27" Monitor, Dell T3600
Im creating plans for a new entryway and so that I have some perspective on how it will all join together i'm also creating a 3d model of my entry idea. In order to move things around to get a better view of how im planning on building this entry, I joined studs together so that I can move things around in the viewport without having to select each object. I know I can grab all the objects at the same time to move but I was wondering IF there is a way to union objects so that they dont lose the lines between joining objects. For example if 2 - 2x8 studs are next to each other and I were to union them, then they would plot as a 4 x 8 instead of 2 - 2 x 8's OR is there a way to maintain lines after union?
View 2 Replies View RelatedHow are normal lines joined together to make one poly line? Learning on Auto CAD 2010.
View 4 Replies View RelatedI quite frequently 'lose' all my vertices on a model - I can still select them, but they are invisible; even the handles on bezier curves suffer, can still see the yellow line but the green dots are hidden.
Would it be a graphics card issue? Yes, I've got the latest drivers, but it happens on ANY machine I work on, with three different cards.
We here at work have recently implemented using the survey database feature in CAD as a better way of manipulating and organizing points in our drawings. However, we have begun to notice a few issues with how the survey database imports points (?).
Sometimes, and I say sometimes because it is very sporratic, some drawings exhibit the issue and some do not, the points will be skewed off the linework (we are converting existing projects to the survey database). In these situations I find that the Northing and Easting don't match the ascii file it was imported from, instead the "Grid Northing" and "Grid Easting" do. Also, some drawings will have a slightly different Grid Northing and Grid Easting vs Northing and Easting, whereas some drawings will have the exact coordinates for both sets of fields. I believe the issue is one and same.
Our points handling goes like this, Data Collector--->TBC (where ground to grid and scaling is performed)---->exported to ascii file------>Imported to CAD.
This is very confusing and irritating at the same time, and really counterproductive to be troubleshooting why our points keep moving. Redrawing the linework is NOT an option, we'll sooner go back to simple ascii file imports (where the problem is NOT present) then have to redo all of our work on our projects.
I need to extend the existing ground profile. I previously had stopped the profile at 25+00 as shown in the attached. However, I need to add on another 100' to 26+00. I can only view info in the Profile Properties. I can't change the end station.
How do I get it to extend?
Previously in LDD when I had a project i needed to transfer from grid to ground I could simply create a block of everything. Scale the entire block from a mid point of the site, explode the block, run check points and done.
Now in C3D 2012 when I explode my block it changes my elevations too. Yikes!!!! Luckily I had a copule of points
elevations labled and I noticed the new "Feature" of scaling my elevations too.
My site is 4,500' across and grid to ground changes it 0.32'
Is there a setting to change this behavior?
I have lots of section views with some surfaces and pipes. Unfortunately, in a number of section views pipes are not shown in full height because the section view level range is too little. What I am wondering is - is it possible to automatically adjust section level ranges so that they fully include pipe sections? Please see also the image in the attachment.
View 2 Replies View Related