Im creating plans for a new entryway and so that I have some perspective on how it will all join together i'm also creating a 3d model of my entry idea. In order to move things around to get a better view of how im planning on building this entry, I joined studs together so that I can move things around in the viewport without having to select each object. I know I can grab all the objects at the same time to move but I was wondering IF there is a way to union objects so that they dont lose the lines between joining objects. For example if 2 - 2x8 studs are next to each other and I were to union them, then they would plot as a 4 x 8 instead of 2 - 2 x 8's OR is there a way to maintain lines after union?
Joining lines into polylines in autocad 2007. Basically, I got stuck when joining several lines together using PEDIT and then Join. At the start, it was very smooth process with no drama. Then, I came across two polylines and wanted to join them together, it just did not work. It works most of the time. Why I can't join certain lines together or two polylines together. This is a 2D drawing CAD.
Sometimes when I am filleting lines they end up joining together like a Polyline. Is there a setting I can turn off that will not allow lines to join when filleting?
I have a compost pad and retention pond to design, I set my back Pad line to surface and then graded to elevation so the slope to the pond will have no cuts
I created a pond and left out the grading to surface on the up hill side towards the pad which will be paved one day. I now created two side feature lines to enclose the whole pad and graded by distance and slope.
My problem now is the two side and back seem to blend together as I attached the feature lines together but I can not figure out how to blend into the pond create as it has side slopes to EG and the front which must join to the side slope crest to enclose the pad to drain into the pond.
I have searched the discussion groep and have not came up with any usefull information.
I have an inside web plate sketch that i want to offset but my offset does only do one line at a time.
So my problem basicly is that I want it to do the whole sketch in one click. Is it possible to join all the lines? or is there another function that I do not know of that will do this for me.
Attached is photos of the problem I have
1 picture - How do I join these lines
2 picture - How the whole sketch looks
3 picture - The offset does only do one line at a time (i want it to do the whole sketch)
how to join line or polylines with ellipse arcs or circle arcs and now.. I give up! Here is my problem: What I would like to draw can be compared with a pear: a succession of circle arcs ellipse arcs and maybe polylines. Once the profile done, I was planning to use REVOLVE or (EXTRUDE + FLLET) to finish my drawing... the problem is that I can't join 2 ellipse arcs from different ellipses (which means neither with a circle arc. How would you proceed to draw a pear?
I used the "break" command to split some lines into segments, but now I can not join them again using PEDIT. They are all on the same elevation. What is preventing me from joining them? I've attached the file in question, I'm trying to join the red (metal layer) lines.
I'm just starting with ACAD 3d. I'm trying to draw a handle for a ball valve. The handle has a horizontal piece and an angled piece. In the attachment, you'll see that there's a gap where the two pieces meet. How can I close the gap so it looks like a seamless piece?
I have two cubes in two different layers so that one is red and one is blue. I want to attach these two cubes together at a surface, but keep that interface between them in the rendering (not just have them combine to form a continuous object with no interfaces).
How do I join two line endpoint together, which terminate at the same anchor point and are at a 90 degree angle, to form a corner instead of a stair step? My problem is on the left, and I want it to look like the right corner.
When I join 2 lines that are dashed (or dotted, I don't know which is the correct name) there's no "corner". See picture below. In one of the corners the lines doesn't meet. In the other there's a "cut-out".
I wanted to join 2 lines together (i.e. end up with a single line). I know that you can join lines by selecting both then using any of the shape / line / brush tools to drag one node from line A over to the a node on line B (you get a little + symbol next to the mouse cursor once the lines can join).
This is fine is you want the final line shape to differ from the original 2, but what if you want to join 2 lines and retain the original paths?
I can do it by postioning the target nodes on eash of the lines almost but not quite touching then using the above technique but its a bit awkward and I suspect this isn't the best way to go about it.
I migrated from AC3D 2010 32-byte to AC3D 2012 64-byte recently. When I migrate my projects to 2012 and open the old 2010 drawings in 2012 I lose the surface lines out of my section sets. It doesn't seem to bother the profile views, only the section views.
Is there a way to work around this problem w/o having to regenerate the section views?
What I'm looking to do is show the hidden lines blocked by a part in a plan view but not all of the hidden lines. Ie. I have a top view showing a clearance. If I turn on that clearance a portion of the original part is not viewed. When I turn on hidden lines I now see every hidden detail of that part (I didn't turn on hidden lines for the entire drawing). I then have to eliminate all the lines I don't want which is both tedious and cumbersome. Is there a way to turn on just the lines hidden by a particular object but not all the hidden lines of the part.
How to evenly space objects between 2 lines. In this instance I am trying to space recessed lights across a ceiling. If I use the divide command and snap to the node the space between the wall and the first light will be greater than the space between the first and second light.
when i am trying to use a function like mirror or offset..etc i will select the lines or objects then i will make a mistake such as selecting the wrong base point or such. i then press esc to end that function and try again but find it annoying that i have to select all the lines again. is there a quicker way to reselect the last lines or objects selected. "like the (L+enter) to use line function type macro".
This is a closed polyline, how can I delete the edge? Is there some sub object selection mode for polylines?
sub_objects.jpg
This was the initial situation or problem, two control points lying on eachother, instead of dragging the edge and removing the extra polyline, is there a way to collapse or weld the overlapping elements?
I produced some objects in Inventor 2013 and exported to DWG to be assembled in AutoCAD 2013. All is fine except when i look at the objects in a 'hidden' view these weird diagonal lines appear over the objects. I am unable to clcik these but when i zoom in they gradually disappear but. If I try to plot the object as shown these lines are printed. This also happens when saving to pdf.
we are using AutoCad 2011 and 2008.When any draw is open everything seems to be just fine, but when we print it out then it came out with lines around the objects(green, grey...)
We have tried 4 different printers with all drivers that we could found on internet, with no success. On the ploter we aren't having any problems and the lines are gone.Also the AutoCad 2006 is without the problems, but we want to move on to the version 11
If the 2D layout is updated I need to move featurelines and gradings to the new locations without changing their Z values. It seems OSNAPZ is supposed to serve this purpose but it's not working for me. I have OSNAPZ=1 and ELEV=0 but when I snap a featureline vertex to the 2D linework the vertex ends up at elevation zero. How do I make this work?
Infrastructure Suite/C3D 2013, LDT 2004, Power Civil v8i SS1 WIN 7 64 PRO HP Pavillion h8xt, i7 2600, 12 GB RADEON 6450, 1 GB
When I use the built-in dwg to PDF for publishing multiable layout tabs I somtimes get extra and/or missing lines and objects on the PDF. When in model space no extra lines a present or missing. Everything is where it need to be. Same goes when a review the drawing in layout before I publish to PDF.
I am looking for a way to use objects created from lines and arcs as text because of a machine that will not read text. The objects look like letters and numbers. I am wondering if there is a way to create a text style, library or whatever with the created "text". There can be hundreds of characters on a single drawing so importing and aligning and placing each object 1 at a time is very slow and painstaking.
I've been working on this project for so long and today when i saved the 3d model, created with autocad architecture 2014,and reopened it, the walls , slabs, doors all changed into lines, but the 3d solids remained the same....i 've attached a photo what happened to my model.
