Because there is a PI in my alignment, the section lines in my corridor are overlapping creating problems with the surface. Is there anything that I can do in this situation?
View 6 RepliesI have 3 alignments running: EB, WB, and Center alignment. My corridor runs along the EB alignment. Is it possible for me to develop section views for this corridor along the Center alignment?
View 6 Replies View RelatedI'm having a random issue with the daylight ties lopes not tieing to the EG surface at all stations in the Corridor Section Editor. Some stations daylight fine. In plan view the daylight lines vary left & right as expected but don't display at all in Section Editor.
Some background info:2012 Civil 3D SP1 / 64 bit / WIN7Simple corridor used1 alignmentSame fg profileSame drefd EG surface (set all targets for daylight LT/RT)Only one assembly applied to entire corridor Attached are 2 captions of the issue I'm having which each have a cut & fill occurrence as well as a caption of the entire align. & corridor. I did try deleting corridor & recreating and even recreated a simpler assembly and still have the daylight issue in same areas of corridor.
I think I just haven't done this in a while and can't find the right setting.
I have existing sections.
I have section views.
I created a corridor.
How do I add the corridor section to my existing cross-section in the section views?
I can view them in the corridor section editor. But I should also be able to add the corridor section to my section views, right?
To plot them, do I NEED to do this through Sheets Sets? I don't have experience with sheet sets yet.
I don't use Civil 3D often enough anymore. Still learning much about the new interface and pulling a design together.
I've got a corridor where the section editor does not show a section that the corridor has created. My frequency is set to 25' with high/low points along curves. At station 22+75, in the model space the corridor shows a section being created (image #2). However, I cannot edit or even see that section in the section editor (image #1). The first screen shot shows the list of stations for the corridor in the editor while the second screenshot shows the model space at the problem station. This is in the middle of a region, so there shouldn't be any issues with other assemblies or regions.
In the section editor, Sta 22+74.91 is listed, skips 22+75, then lists 23+00. I am needing to manually adjust the cross slopes of my lanes. If I view the surface there is a weird dip because at station 22+75 the default slope of my lane is -2%. I cannot edit station 22+75, so I cannot adjust the cross slope of the lanes.
What is causing the section editor to not even recognize a section? How can I edit the cross slope at station 22+75 if the editor doesn't even display that section?
Infrastructure Design Suite Premium 2014
Civil 3D 2014 x64
Windows 7 64-bit
6GB RAM
C3D 2012...but this feature has probably been in C3D for sometime
1-What is a 'Line Marker in Section' Section component of an Alignment Style?
2-How is it used (example )?
When creating an alignment from corridor feature (ditch invert level), the created alignment is not following the selected line (see image bellow). The alignment seams to be created from the first point of the feature line to the last point and ignores all the other points. The vertical alignment created at the same time seams to be correct.
View 1 Replies View RelatedI want use my corridor where I need it and not use one in certain areas. For a proposed dike. Some places doesn't need to be replace.
So I need a way to use my section on the alignment. where I can find that option?
My alignment runs on the road center line and ends at the center of the cal-de-sac bubble. My corridor runs to the middle of the cal-de-sac. I need to shorten the corridor to end where the constant road width ends and the bulb of the cal-de-sac begins. I can shorten the Corridor on the alignment or do I need to create a new alignment to the desired length?
View 5 Replies View RelatedDuring modelling an intersection I need a corridor edge as target for onther region (attached picture),
I made the alignment from corridor but unfortunately there is no option for that aligment to be dynamic!!!!!
every time I changed the main road layout, I have to delete the Edge alignment and make a new one.
I have the centerline of a berm constructed using a 3D polyline. I want to use this centerline as the Alignment that I need from which to create a Corridor. When I try to create an Alignment from objects, I can only use a 2D polyline, not 3D. The berm has a slope to it and I need to have the assembly follow that slope as I create the Corridor. Do I need to create the Alignment in 2D and then edit the points for elevation?
View 7 Replies View Relatedi am trying to get the coordinate value for the current station in the subassemblies.
i found
Autodesk.Civil.Roadway.DatabaseServices.BaseBaseline.StationOffsetElevationToXYZ(ByRef Autodesk.AutoCAD.Geometry.Point3d) As Autodesk.AutoCAD.Geometry.Point3d
but how you get the basebaseline?
in the alignment object there is no convert station to coordinate only coordinate to station. which is useless in this case.
Civil 3D 2012
Work: Xeon W3503, 12GB, Quadro 2000, Dell P2211H x 2
Home: 3930k, 12GB, GTX 590, U3011, QX2710
For an intersection, I am trying to create an alignment and profile from the Lane (edge of traveled way) of my main road for the intersection lanes to tie to. I just did this yesterday on this same corridor without any issue, but today it doesn't create the alignment correctly. It doesn't actually follow the feature line that I select. The alignment is in orange and the green line is the lane line. Notice that the alignment isn't following the lane line.
What would cause this? It worked fine doing the exact same thing yesterday, but today it's not.
Infrastructure Design Suite Premium 2014
Civil 3D 2014 x64
Windows 7 64-bit
6GB RAM
Using Civil 3D 2012 SP 1 on Win7 Pro 64-bit.
Is there any reason why a corridor model would not be respecting the manually entered super elevation values in the alignment? I have several stations that should be calculated with even super elevation values, but they aren't. For example, at station 0+080 on my alignment the left crown should be running at -3%, but it is actually being calculated at -2.47%. It isn't just one station; it's most of them. No overridden stations, vertical targets, etc in the corridor. Just a fairly straight-forward align (hor/vert) with super, simple assembly (two lanes, shoulder, daylight), simple corridor.
how label only the top of my road surface in section view? The road slopes -2% towards a ditch but my my code set labels both the top of road(-2%) and what I assume is the bottom of the road surface (2%) which I don't want to show.
Is it also possible to label my side slopes as 4:1 instead of 25%?
is it possible to get the alignment name which the corridor surface is built from when the surface is being data referenced. in other word no corridor as the middleman.
the way i see it is when corridor suface is referenced, it becomes a regular surface and loses some properties such as parent alignment.
i am still using COM. maybe .net can do it? either way works.
Civil 3D 2012
Work: Xeon W3503, 12GB, Quadro 2000, Dell P2211H x 2
Home: 3930k, 12GB, GTX 590, U3011, QX2710
I created a base drawing for sections that references an alignment. I xrefed in the drawing where my corridor was created. When I create the section views, the corridor shows up perfectly.
I then created a blank sheet and xrefed in my section view base drawing.In this sheet drawing, only parts of the corridors are visible.I have a C&G on one assembly and a shoulder on another assembly that aren't visible. (see pics)The first pic is my section base drawing.
When creating a Corridor Section Points Report using the Toolspace>Toolbox>Reports Manager in Civil 3D 2012, the stations get listed but only a few contain point information (see attached).
I am trying to generate stake-out data for a proposed road. I was able to get this report to work successfully in one of the Civil 3D tutorials, so I assume that nothing is wrong with the utility. The problem may be related to my corridor.
I am doing public works type project. A simple road widening project. I created an alignment, surface, profile view and basic road assembly (from tool palettes) and corridor.
I created a corridor and referenced it to my "profile view", "alignment" and to "basic road" assembly. When I created section views, it shows only existing grade based on the surface and the basic road assembly is not showing on my sections. I can't figure out how to do it.
C3D 2012
When I open the Corridor Section Editor, the Ribbon changes to the Section Editor ribbon, but the section window doesn't come up. If I pan around, parts of the drawing disappear. If I close the editor and regen, everything comes back.
Below is the current status of our working view in the 2014 Corridor Section Editor. I can't see us getting any value for our investment into Civil 3D 2014, before Civil 3D 2015 comes out now.
The polar opposite is actually true, we had too much downtime encountering, analyzing and reporting product defects, and it affected profitability and capability.
C3D 2014 SP1
W7x64; i7 8gb; Radeon HD 5700
I have a single corridor "section" that extends from the 'tip' of my cul-de-sac back to the start of the alignment.I scoured the group before posting and didn't see anything quite the same.Would it have something to do with the corridor line being parallel to the alignment?
View 2 Replies View RelatedI have a problem with the corridor section points report on Civil 3d 2014. It only presents the first station on the corridor.
Attached image.
Using 2012, latest SP. I have a master drawing @ 1:500 with alignment, prof's, corr, etc. I have a second drawing @ 1:200 to be used for section views. I've data referenced the alignment, prof's, srf's, etc. I've created the section views in the section view dwg and xref'd the master dwg.
My problem is that the corridor model will not display in section views anywhere along a spiral in the 1:200 dwg. It displays fine everywhere else along the alignment. Just not spirals.
I have section views in the master drawing that will display the corridor just fine in section view at these same stations along the spirals.
How do I access the Corridor Section Editor view settings and copy them from one drawing to another?
View 1 Replies View RelatedI changed my Corridor Prop : From "Specific Code" : Top to Datum as shown below
and afterwards my section view Don't have the corridor in it !!
I tried to creat a new one but in the Section Creation tool i could not find surfaces :
Sony VPCCW26FA
Intel Core i5 M 520 @ 2.40GHz
8192MB RAM
NVIDIA GeForce GT 330M 512MB Dedicated
Is it possible to adjust the vertical exageration of the section view in the corridor section editor?
View 1 Replies View RelatedI am trying to find out if there is a way to change the code for the Corridor Section Points Report. See attachment.
In page 1 of the attachment you will see the names that we prefer for the different zones in our assembly as per our Standards.
On page 2 is the default names that C3D spits out as defaults (under String Cut).
We are running C3D 2012.
How do I get rid of the green circles in cross section editor? I have looked in the code set styles, and I have found nothing that will resolve this.
View 2 Replies View RelatedI am attempting to create section views from a corridor. I have about 80 sections total that I would really like to stack 3 high...then just across the page. Any step by step that make this process easy to understand?
Right now I get 10 high then across the page (using 'draft' option). I've tried to make a dwt at a 10 scale, (setting the viewport at 10 scale and viewport as a 'section' in the properties), but when I use that, the sections start overlapping (this is using the 'production' option).
Anyway, I'm trying to build a corridor that targets the existing surface with a linkslopetosurface sub. It works just like I want it to, but there are areas where I want to override the target and have it target an existing curb return alignment. Is there a better sub I should be using that will target one first and then a second if the first doesn't work right?
Also, with my corridor section editor, can I adjust the vertical scale to be exagerated? It's really tough to edit the 1:1 ver./hor. scale.