I have a single corridor "section" that extends from the 'tip' of my cul-de-sac back to the start of the alignment.I scoured the group before posting and didn't see anything quite the same.Would it have something to do with the corridor line being parallel to the alignment?
View 2 RepliesI think I just haven't done this in a while and can't find the right setting.
I have existing sections.
I have section views.
I created a corridor.
How do I add the corridor section to my existing cross-section in the section views?
I can view them in the corridor section editor. But I should also be able to add the corridor section to my section views, right?
To plot them, do I NEED to do this through Sheets Sets? I don't have experience with sheet sets yet.
I don't use Civil 3D often enough anymore. Still learning much about the new interface and pulling a design together.
I've got a corridor where the section editor does not show a section that the corridor has created. My frequency is set to 25' with high/low points along curves. At station 22+75, in the model space the corridor shows a section being created (image #2). However, I cannot edit or even see that section in the section editor (image #1). The first screen shot shows the list of stations for the corridor in the editor while the second screenshot shows the model space at the problem station. This is in the middle of a region, so there shouldn't be any issues with other assemblies or regions.
In the section editor, Sta 22+74.91 is listed, skips 22+75, then lists 23+00. I am needing to manually adjust the cross slopes of my lanes. If I view the surface there is a weird dip because at station 22+75 the default slope of my lane is -2%. I cannot edit station 22+75, so I cannot adjust the cross slope of the lanes.
What is causing the section editor to not even recognize a section? How can I edit the cross slope at station 22+75 if the editor doesn't even display that section?
Infrastructure Design Suite Premium 2014
Civil 3D 2014 x64
Windows 7 64-bit
6GB RAM
how label only the top of my road surface in section view? The road slopes -2% towards a ditch but my my code set labels both the top of road(-2%) and what I assume is the bottom of the road surface (2%) which I don't want to show.
Is it also possible to label my side slopes as 4:1 instead of 25%?
I created a base drawing for sections that references an alignment. I xrefed in the drawing where my corridor was created. When I create the section views, the corridor shows up perfectly.
I then created a blank sheet and xrefed in my section view base drawing.In this sheet drawing, only parts of the corridors are visible.I have a C&G on one assembly and a shoulder on another assembly that aren't visible. (see pics)The first pic is my section base drawing.
When creating a Corridor Section Points Report using the Toolspace>Toolbox>Reports Manager in Civil 3D 2012, the stations get listed but only a few contain point information (see attached).
I am trying to generate stake-out data for a proposed road. I was able to get this report to work successfully in one of the Civil 3D tutorials, so I assume that nothing is wrong with the utility. The problem may be related to my corridor.
I am doing public works type project. A simple road widening project. I created an alignment, surface, profile view and basic road assembly (from tool palettes) and corridor.
I created a corridor and referenced it to my "profile view", "alignment" and to "basic road" assembly. When I created section views, it shows only existing grade based on the surface and the basic road assembly is not showing on my sections. I can't figure out how to do it.
C3D 2012
When I open the Corridor Section Editor, the Ribbon changes to the Section Editor ribbon, but the section window doesn't come up. If I pan around, parts of the drawing disappear. If I close the editor and regen, everything comes back.
Below is the current status of our working view in the 2014 Corridor Section Editor. I can't see us getting any value for our investment into Civil 3D 2014, before Civil 3D 2015 comes out now.
The polar opposite is actually true, we had too much downtime encountering, analyzing and reporting product defects, and it affected profitability and capability.
C3D 2014 SP1
W7x64; i7 8gb; Radeon HD 5700
I have a problem with the corridor section points report on Civil 3d 2014. It only presents the first station on the corridor.
Attached image.
Using 2012, latest SP. I have a master drawing @ 1:500 with alignment, prof's, corr, etc. I have a second drawing @ 1:200 to be used for section views. I've data referenced the alignment, prof's, srf's, etc. I've created the section views in the section view dwg and xref'd the master dwg.
My problem is that the corridor model will not display in section views anywhere along a spiral in the 1:200 dwg. It displays fine everywhere else along the alignment. Just not spirals.
I have section views in the master drawing that will display the corridor just fine in section view at these same stations along the spirals.
Because there is a PI in my alignment, the section lines in my corridor are overlapping creating problems with the surface. Is there anything that I can do in this situation?
View 6 Replies View RelatedHow do I access the Corridor Section Editor view settings and copy them from one drawing to another?
View 1 Replies View RelatedI changed my Corridor Prop : From "Specific Code" : Top to Datum as shown below
and afterwards my section view Don't have the corridor in it !!
I tried to creat a new one but in the Section Creation tool i could not find surfaces :
Sony VPCCW26FA
Intel Core i5 M 520 @ 2.40GHz
8192MB RAM
NVIDIA GeForce GT 330M 512MB Dedicated
Is it possible to adjust the vertical exageration of the section view in the corridor section editor?
View 1 Replies View RelatedI am trying to find out if there is a way to change the code for the Corridor Section Points Report. See attachment.
In page 1 of the attachment you will see the names that we prefer for the different zones in our assembly as per our Standards.
On page 2 is the default names that C3D spits out as defaults (under String Cut).
We are running C3D 2012.
I have 3 alignments running: EB, WB, and Center alignment. My corridor runs along the EB alignment. Is it possible for me to develop section views for this corridor along the Center alignment?
View 6 Replies View RelatedHow do I get rid of the green circles in cross section editor? I have looked in the code set styles, and I have found nothing that will resolve this.
View 2 Replies View RelatedI am attempting to create section views from a corridor. I have about 80 sections total that I would really like to stack 3 high...then just across the page. Any step by step that make this process easy to understand?
Right now I get 10 high then across the page (using 'draft' option). I've tried to make a dwt at a 10 scale, (setting the viewport at 10 scale and viewport as a 'section' in the properties), but when I use that, the sections start overlapping (this is using the 'production' option).
Anyway, I'm trying to build a corridor that targets the existing surface with a linkslopetosurface sub. It works just like I want it to, but there are areas where I want to override the target and have it target an existing curb return alignment. Is there a better sub I should be using that will target one first and then a second if the first doesn't work right?
Also, with my corridor section editor, can I adjust the vertical scale to be exagerated? It's really tough to edit the 1:1 ver./hor. scale.
What could be the trick with corridor section editor in C3D 2014, applying overrides to a stations range won't work. After selecting or typing end station in the 'apply to a station range' prompt nothing happens, the overrides just will not be applied.
To apply overrides for an subassembly (curb depth etc) I must go through all the stations set by corridor frequency in the station range. This is not file specific, as it is the case with all my projects.
Edited a corridor section. Hit some button (not sure what) now I can't get back to my regular view. If I select the "Top" view, now all that shows up is one contour, and the top of one cross section, like it's only showing stuff that is at one elevation.
View 1 Replies View RelatedI've worked with LDD for 11 yrs. Last week the IT guys changed my PC to Windows 7 64bit, so I can't have LDD and I have to work with C3D. so I am following software tutorials.
for designing a road I created:
alignment ---> surface profile ---> layout profile (project line) ---> assembly ---> subassemblies ---> corridor ---> set target surface and frequencies
Corridor is created with daylights ,but I don't see existing ground in corridor section editor.
There is nothing about this in tutorial. Also I don't know how to calculate the volumes, in LDD after this stage we could calculate the volumes. i think in C3D I should do more for calculation.
I would like to have my corridor section points report to have different labels for the points like Edge of Shoulder or EOP instead of labels like P2 and Hinge. Is the only way to do this to somehow change the codes in the stock subassemblies?
Civil 3D 2014
The FG was created from the corridor.
The cross sections show the EG, FG and Corridor. Yet the Corridor is NOT ON the FG surface.
This is only happening on one section (0+20). The other sections look good.
how to have exisitng cross slopes display on a bank of corridor cross sections...I see lots of posts on this but I am having trouble finding the answer. The link below from Add a section view grade label only adds "A" slope label.....I want all of them in all of my sections.
[URL]
I have a problem with editing in link code because it didn't appear in corridor section view as you can in attached files.
View 9 Replies View RelatedAt entry / exit ramp connection,
Since frequencies of corridors are perpendicular to their respective alignments, there is gap developed in between two corridors on ramp as shown in snaps.
This is common problem in roads & highways, I know how fix the same.
But if my cross section is a Tunnel? (Cross Section- Elliptical Roof)
Civil 3D 2012, SAC
16 GB Ram 64 Bit Win7
I have a cround road with curb and gutter, sidewalk, a retaining wall, and pan at the top of the retaining wall behind it, and then a link slope to surface. From station 3+40 to 3+50 we are not putting in any pan. The topp of the the wall at these stations is at existing grade.
When I go into my corridor section editor at station 3+40 and delete the pan behind the wall it goes away. When I click on "apply to range of stations" and put in 3+50 for the end station, my corridor sections do not change. Why is this? 3+40 stays changed but thats the only one. I have rebuild automatic set and even if I click the update corridor button, it does not apply this station range.
I'm having a random issue with the daylight ties lopes not tieing to the EG surface at all stations in the Corridor Section Editor. Some stations daylight fine. In plan view the daylight lines vary left & right as expected but don't display at all in Section Editor.
Some background info:2012 Civil 3D SP1 / 64 bit / WIN7Simple corridor used1 alignmentSame fg profileSame drefd EG surface (set all targets for daylight LT/RT)Only one assembly applied to entire corridor Attached are 2 captions of the issue I'm having which each have a cut & fill occurrence as well as a caption of the entire align. & corridor. I did try deleting corridor & recreating and even recreated a simpler assembly and still have the daylight issue in same areas of corridor.
I am using C3D 2013, I have a corridor created using a Primary Road Full Section as my assembly, I have all the slopes and ditching set, when I go to model the corridor the ditching is not showing correctly, only small sections of the ditching are showing when I know there should be more. I have the assembly setup to build the ditching when there is less than a meter fill, but will not work.
View 3 Replies View Related