I am trying to find out if there is a way to change the code for the Corridor Section Points Report. See attachment.
In page 1 of the attachment you will see the names that we prefer for the different zones in our assembly as per our Standards.
On page 2 is the default names that C3D spits out as defaults (under String Cut).
We are running C3D 2012.
I would like to have my corridor section points report to have different labels for the points like Edge of Shoulder or EOP instead of labels like P2 and Hinge. Is the only way to do this to somehow change the codes in the stock subassemblies?
Civil 3D 2014
When creating a Corridor Section Points Report using the Toolspace>Toolbox>Reports Manager in Civil 3D 2012, the stations get listed but only a few contain point information (see attached).
I am trying to generate stake-out data for a proposed road. I was able to get this report to work successfully in one of the Civil 3D tutorials, so I assume that nothing is wrong with the utility. The problem may be related to my corridor.
I have a problem with the corridor section points report on Civil 3d 2014. It only presents the first station on the corridor.
Attached image.
I have created surfaces for my original ground and my corridor. Both have appropriate boundaryies and the TIN looks good for both. I am trying to create a volume report through Volume Dashboard. I am able to create the volume surface with no issues but the numbers it comes up with do not seem correct. I can see from my profile that there is a small fill but the software seems to create a fill that is almost half of all the material when my profile shows there is more cut.
I tried creating a sample line group...it also shows the majority is cut. The only thing I can think is that there are about a dozen areas where my daylight does not work. how to do this volume correctly?
I am trying to get a material volume report for a corridor structure. The overall dirt cut fill is working, but the pavement and base keeps showing up as zero.
I started with the surfaces made, (perhaps that’s the problem,) I made an alignment, used an assembly, made a profile, and sample lines, made the corridor. The assembly draws in the cross sections, but the materials report shows zero in the pavement and stone.
I have an existing surface. I created an alignment and have managed to make "multiple cross" section out of the surface without making corridor and its fine. Now, the problem is I cannot finding any option to make report out of these sections. I need those report very soon..I have even attached th dwg file which contains all the data.
View 9 Replies View RelatedI think I just haven't done this in a while and can't find the right setting.
I have existing sections.
I have section views.
I created a corridor.
How do I add the corridor section to my existing cross-section in the section views?
I can view them in the corridor section editor. But I should also be able to add the corridor section to my section views, right?
To plot them, do I NEED to do this through Sheets Sets? I don't have experience with sheet sets yet.
I don't use Civil 3D often enough anymore. Still learning much about the new interface and pulling a design together.
I've got a corridor where the section editor does not show a section that the corridor has created. My frequency is set to 25' with high/low points along curves. At station 22+75, in the model space the corridor shows a section being created (image #2). However, I cannot edit or even see that section in the section editor (image #1). The first screen shot shows the list of stations for the corridor in the editor while the second screenshot shows the model space at the problem station. This is in the middle of a region, so there shouldn't be any issues with other assemblies or regions.
In the section editor, Sta 22+74.91 is listed, skips 22+75, then lists 23+00. I am needing to manually adjust the cross slopes of my lanes. If I view the surface there is a weird dip because at station 22+75 the default slope of my lane is -2%. I cannot edit station 22+75, so I cannot adjust the cross slope of the lanes.
What is causing the section editor to not even recognize a section? How can I edit the cross slope at station 22+75 if the editor doesn't even display that section?
Infrastructure Design Suite Premium 2014
Civil 3D 2014 x64
Windows 7 64-bit
6GB RAM
When I change a section to static mode, I would like to add new section points or erase section points.
Autocad Civil 3D 2014 +SP1
Quad Core Intel i7 3770-cpu 3.40Ghz.
ssd samsung 840 pro 512gb+ssd samsung 840 pro 256 gb+1tb hdd
32gb RAM 1600 Mhz.
nVidia Quadro 2000.
Win 7 Pro 64bit
A co-worker asked if I could create a report that listed the station and offset values for selected points & alignment. After selecting "execute" for the Station Offset to Points report, the file gets hung up before I can select the points and alignment I want.
I've tried xml-ing out the desired points & alignment into another file and running the report from..
All other reports under Alignment and Points work fine (drawing does not have other C3D objects).
I'm using C3D 2011 version 3.
Civil 3D 2013
Toolspace > Toolbox > Reports Manager > Points > Station Offset to Points
why point number 9 comes after 1 instead of 8?
Clicking on the column headers to sort does not work.
Found another report of this, but in an earlier version of C3D.
[URL]
When I Create a Station offset to points report, the points are out of order and it does not display all of the points.
View 2 Replies View Relatedi found a way to get a report of my cogo points relative to an alignment i.e. station offset. problem is, i have thousands of points in my drawing. is there a way to get only a few, or a group of points to show up on the report instead of ALL of them?
View 1 Replies View Relatedhow label only the top of my road surface in section view? The road slopes -2% towards a ditch but my my code set labels both the top of road(-2%) and what I assume is the bottom of the road surface (2%) which I don't want to show.
Is it also possible to label my side slopes as 4:1 instead of 25%?
I created a base drawing for sections that references an alignment. I xrefed in the drawing where my corridor was created. When I create the section views, the corridor shows up perfectly.
I then created a blank sheet and xrefed in my section view base drawing.In this sheet drawing, only parts of the corridors are visible.I have a C&G on one assembly and a shoulder on another assembly that aren't visible. (see pics)The first pic is my section base drawing.
I am doing public works type project. A simple road widening project. I created an alignment, surface, profile view and basic road assembly (from tool palettes) and corridor.
I created a corridor and referenced it to my "profile view", "alignment" and to "basic road" assembly. When I created section views, it shows only existing grade based on the surface and the basic road assembly is not showing on my sections. I can't figure out how to do it.
C3D 2012
When I open the Corridor Section Editor, the Ribbon changes to the Section Editor ribbon, but the section window doesn't come up. If I pan around, parts of the drawing disappear. If I close the editor and regen, everything comes back.
Below is the current status of our working view in the 2014 Corridor Section Editor. I can't see us getting any value for our investment into Civil 3D 2014, before Civil 3D 2015 comes out now.
The polar opposite is actually true, we had too much downtime encountering, analyzing and reporting product defects, and it affected profitability and capability.
C3D 2014 SP1
W7x64; i7 8gb; Radeon HD 5700
I have a single corridor "section" that extends from the 'tip' of my cul-de-sac back to the start of the alignment.I scoured the group before posting and didn't see anything quite the same.Would it have something to do with the corridor line being parallel to the alignment?
View 2 Replies View RelatedUsing 2012, latest SP. I have a master drawing @ 1:500 with alignment, prof's, corr, etc. I have a second drawing @ 1:200 to be used for section views. I've data referenced the alignment, prof's, srf's, etc. I've created the section views in the section view dwg and xref'd the master dwg.
My problem is that the corridor model will not display in section views anywhere along a spiral in the 1:200 dwg. It displays fine everywhere else along the alignment. Just not spirals.
I have section views in the master drawing that will display the corridor just fine in section view at these same stations along the spirals.
I am using the COGO Points from Corridor command but would like to limit the freqency of the created points to only every 50 ft (half station) or so. Is there a command I can change to make this happen ??
I've checked the CreatePointsFromCorridor command setting and it doesn't seem to be there...
Because there is a PI in my alignment, the section lines in my corridor are overlapping creating problems with the surface. Is there anything that I can do in this situation?
View 6 Replies View RelatedHow do I access the Corridor Section Editor view settings and copy them from one drawing to another?
View 1 Replies View RelatedI changed my Corridor Prop : From "Specific Code" : Top to Datum as shown below
and afterwards my section view Don't have the corridor in it !!
I tried to creat a new one but in the Section Creation tool i could not find surfaces :
Sony VPCCW26FA
Intel Core i5 M 520 @ 2.40GHz
8192MB RAM
NVIDIA GeForce GT 330M 512MB Dedicated
Is it possible to adjust the vertical exageration of the section view in the corridor section editor?
View 1 Replies View RelatedI have 3 alignments running: EB, WB, and Center alignment. My corridor runs along the EB alignment. Is it possible for me to develop section views for this corridor along the Center alignment?
View 6 Replies View RelatedHow do I get rid of the green circles in cross section editor? I have looked in the code set styles, and I have found nothing that will resolve this.
View 2 Replies View RelatedI am attempting to create section views from a corridor. I have about 80 sections total that I would really like to stack 3 high...then just across the page. Any step by step that make this process easy to understand?
Right now I get 10 high then across the page (using 'draft' option). I've tried to make a dwt at a 10 scale, (setting the viewport at 10 scale and viewport as a 'section' in the properties), but when I use that, the sections start overlapping (this is using the 'production' option).
Anyway, I'm trying to build a corridor that targets the existing surface with a linkslopetosurface sub. It works just like I want it to, but there are areas where I want to override the target and have it target an existing curb return alignment. Is there a better sub I should be using that will target one first and then a second if the first doesn't work right?
Also, with my corridor section editor, can I adjust the vertical scale to be exagerated? It's really tough to edit the 1:1 ver./hor. scale.
Cannot get corridor surface boundary from daylight points. Is there another way so that I do not have to trace the outer limits?
View 3 Replies View Related