AutoCAD Civil 3D :: Existing Ground Not Shown In Corridor Section Editor
Jul 7, 2011
I've worked with LDD for 11 yrs. Last week the IT guys changed my PC to Windows 7 64bit, so I can't have LDD and I have to work with C3D. so I am following software tutorials.
for designing a road I created:
alignment ---> surface profile ---> layout profile (project line) ---> assembly ---> subassemblies ---> corridor ---> set target surface and frequencies
Corridor is created with daylights ,but I don't see existing ground in corridor section editor.
There is nothing about this in tutorial. Also I don't know how to calculate the volumes, in LDD after this stage we could calculate the volumes. i think in C3D I should do more for calculation.
View 9 Replies
ADVERTISEMENT
Sep 1, 2013
How to prepare for rendering Existing ground with cutted corridor river? Specially in places where corridor river is below EG. If there is some tool like cut?
View 4 Replies
View Related
Mar 5, 2012
I think I just haven't done this in a while and can't find the right setting.
I have existing sections.
I have section views.
I created a corridor.
How do I add the corridor section to my existing cross-section in the section views?
I can view them in the corridor section editor. But I should also be able to add the corridor section to my section views, right?
To plot them, do I NEED to do this through Sheets Sets? I don't have experience with sheet sets yet.
I don't use Civil 3D often enough anymore. Still learning much about the new interface and pulling a design together.
View 3 Replies
View Related
Mar 8, 2012
I've got a corridor where the section editor does not show a section that the corridor has created. My frequency is set to 25' with high/low points along curves. At station 22+75, in the model space the corridor shows a section being created (image #2). However, I cannot edit or even see that section in the section editor (image #1). The first screen shot shows the list of stations for the corridor in the editor while the second screenshot shows the model space at the problem station. This is in the middle of a region, so there shouldn't be any issues with other assemblies or regions.
In the section editor, Sta 22+74.91 is listed, skips 22+75, then lists 23+00. I am needing to manually adjust the cross slopes of my lanes. If I view the surface there is a weird dip because at station 22+75 the default slope of my lane is -2%. I cannot edit station 22+75, so I cannot adjust the cross slope of the lanes.
What is causing the section editor to not even recognize a section? How can I edit the cross slope at station 22+75 if the editor doesn't even display that section?
Infrastructure Design Suite Premium 2014
Civil 3D 2014 x64
Windows 7 64-bit
6GB RAM
View 6 Replies
View Related
May 15, 2012
While I was out, my partner somehow now has two existing ground lines in my cross-sections. ####exist and ####exist (1). They are offset by about .5 feet left to right. Where do I remove the surtface ###exst (1) from the cross sections. I am looking now.
View 2 Replies
View Related
Jun 22, 2012
C3D 2012
When I open the Corridor Section Editor, the Ribbon changes to the Section Editor ribbon, but the section window doesn't come up. If I pan around, parts of the drawing disappear. If I close the editor and regen, everything comes back.
View 5 Replies
View Related
Oct 4, 2013
Below is the current status of our working view in the 2014 Corridor Section Editor. I can't see us getting any value for our investment into Civil 3D 2014, before Civil 3D 2015 comes out now.
The polar opposite is actually true, we had too much downtime encountering, analyzing and reporting product defects, and it affected profitability and capability.
C3D 2014 SP1
W7x64; i7 8gb; Radeon HD 5700
View 1 Replies
View Related
May 25, 2012
How do I access the Corridor Section Editor view settings and copy them from one drawing to another?
View 1 Replies
View Related
Apr 30, 2013
Is it possible to adjust the vertical exageration of the section view in the corridor section editor?
View 1 Replies
View Related
Jul 26, 2013
I have 3 alignments running: EB, WB, and Center alignment. My corridor runs along the EB alignment. Is it possible for me to develop section views for this corridor along the Center alignment?
View 6 Replies
View Related
Aug 24, 2012
How do I get rid of the green circles in cross section editor? I have looked in the code set styles, and I have found nothing that will resolve this.
View 2 Replies
View Related
May 4, 2012
how to have exisitng cross slopes display on a bank of corridor cross sections...I see lots of posts on this but I am having trouble finding the answer. The link below from Add a section view grade label only adds "A" slope label.....I want all of them in all of my sections.
[URL]
View 6 Replies
View Related
Jul 29, 2013
What could be the trick with corridor section editor in C3D 2014, applying overrides to a stations range won't work. After selecting or typing end station in the 'apply to a station range' prompt nothing happens, the overrides just will not be applied.
To apply overrides for an subassembly (curb depth etc) I must go through all the stations set by corridor frequency in the station range. This is not file specific, as it is the case with all my projects.
View 1 Replies
View Related
Jul 13, 2012
I'm having a random issue with the daylight ties lopes not tieing to the EG surface at all stations in the Corridor Section Editor. Some stations daylight fine. In plan view the daylight lines vary left & right as expected but don't display at all in Section Editor.
Some background info:2012 Civil 3D SP1 / 64 bit / WIN7Simple corridor used1 alignmentSame fg profileSame drefd EG surface (set all targets for daylight LT/RT)Only one assembly applied to entire corridor Attached are 2 captions of the issue I'm having which each have a cut & fill occurrence as well as a caption of the entire align. & corridor. I did try deleting corridor & recreating and even recreated a simpler assembly and still have the daylight issue in same areas of corridor.
View 2 Replies
View Related
Nov 11, 2013
Unable to edit parameters in Corridor Section Parameter Editor
View 4 Replies
View Related
Jan 9, 2014
I have added intermediate sample lines in my corridor. These sections appear in the section editor and I can make changes to the data. The changes show correctly in the section editor and section view, however, when I plot the cross sections some of these added stations do not show the overrides. They are showing the original assembly group parameters. How do I get all the cross sections to reflect the edited data from the section editor?
View 3 Replies
View Related
Sep 28, 2012
I'm trying to create an all new existing surface over existing ground. I have a TIN surface of the EG, and I have drawn overlay splines that describe the new surface, but how to go about creating that design surface.
It is a compound surface, open on one end and closed all around on the other, somewhat like a half of a football stadium, but with an irregular upper edge because I am needing to figure out cuts and fills to manipulate the EG into this new surface without costly major terraforming. There is about 40-50' vertical elevation between the "field" and the upper rim with a generally constant 7-10 deg. slope all around. I'm just at a loss to figure out how to approach this project, and am quite new to Civil 3D.
Civil3D 2013
MacBookPro 17 - 2.4GHz Intel QuadCore i7 (Late 2011 build)
Microsoft Windows 7 64bit
350GB Bootcamp volume
View 2 Replies
View Related
Oct 12, 2012
I have an existing ground surface with all different z co-ords and im trying to add three proposed buildings to my exisiting ground with all the builidngs having a level of 32.5 as a minimum, however at some points the ground is higher than 32.5 and I only want to raise my existing ground to 32.5 within the proposed buidling layout if it is below 32.5 as im doing a flood calculation. What do i need to for this?
View 2 Replies
View Related
Mar 27, 2012
I have a rather large project for a roadway reconstruction. Therefore, the existing utilities are in a separate drawing and the existing ground surface model is in a separate drawing. All the above surface items (curb and gutter, asphalt, concrete, signs, sidewalks, landscaping, etc..) are in the master drawing. I then xref'd in my utility drawing and though I would use data shortcuts for my existing ground surface drawing. I took the surveyed triangles (3d faces) from our raw survey drawing and copied them into my surface drawing, created a surface from the triangles, created a boundary and such. So far everything is good. I created the working folder for the data shortcuts for this project and saved the drawing and closed it. I went into my master drawing and clicked on "Create Reference". I did not promote. The reference came though and everything is fine. Now I want to add contour labels in my surface drawing which I did but they do not show up in my master drawing but the contours themselves do. Do I have to promote this drawing into my master drawing so I can create the contour labels in my master drawing? I guess that is fine but the issue is we have small areas of topo that will be added as needed down the road. If I promote the surface drawing into my master drawing then when I add topo to the surface drawing, it wont update in my master drawing.
View 9 Replies
View Related
Apr 11, 2012
I have a feature line as the top of a wall and want to grade up away from it to marry to existing ground.
View 1 Replies
View Related
Aug 9, 2013
How can the cross sections be setup to label the existing and proposed grade at the centerline of a cross section, see attached. Could do this in LD but have not been able to figure it out in Civil 3D
C3D 2013 (latest updates), 2014 Infrastructure Design Suite
Win 7 Pro, 64-bit
16 GB RAM
View 1 Replies
View Related
Dec 15, 2008
I have an existing ground profile, and a design profile. All I want to do is label the slopes of the design. When I click my line label style and turn on the text it labels the existing ground and the design ground. I cannot find the setting in my two profile styles to turn the slopes off in the existing ground.
Oh, how can I get a tick on the V.C. dimension line?
View 6 Replies
View Related
Mar 28, 2012
I am trying to label existing ground & profile grade on my cross-sections the way old Land 4 used to do it. I've muddled through section view property style settings, band settings, group properties w/no luck. It can't possible be this difficult. What am I missing?
View 5 Replies
View Related
Dec 18, 2013
How to get automaticly data on the profile. See my road profile in attachment.
Now i have to manually write data of elevation of existing and future ground and distance.
i think that is possible automaticly, but i dont know how.
View 2 Replies
View Related
Aug 12, 2013
In my section editor my labels show up correctly and in all the locations I want. But then, in my cross section file, I look in my section views and they are completely different. When I try to label more points under the Code Set Styles, they won't even show up on my section views.
View 6 Replies
View Related
Jun 13, 2013
I migrated from AC3D 2010 32-byte to AC3D 2012 64-byte recently. When I migrate my projects to 2012 and open the old 2010 drawings in 2012 I lose the surface lines out of my section sets. It doesn't seem to bother the profile views, only the section views.
Is there a way to work around this problem w/o having to regenerate the section views?
View 3 Replies
View Related
May 10, 2012
I have a problem with point codes in section views in civil3d 2013. They are not showing at all. Drawing was made in civil3d 2012 and all point codes with defined styles were displayed correctly in section views and now they are all gone. Just link codes are shown. Is there something in setup of code styles that has to be changed?
Even if i set up new code and new label style it does not show up in section view after rebuild. Just in assembly.
If i do the same for link label it does show both in assembly and in section views.
View 1 Replies
View Related
Jan 11, 2013
i have a corridor. the corridor feature line that is supposed to hit the proposed centerline is following my existing grade instead of where the profile is. in other words, the corridor line i need at the centerline when i do "feature lines from corridor" is following my existing grade instead of the top of my road. did i accid. change something? i need it to follow the top centerline of my road. the red arrow is the line i need at the top centerline.
View 3 Replies
View Related
Jun 21, 2012
how label only the top of my road surface in section view? The road slopes -2% towards a ditch but my my code set labels both the top of road(-2%) and what I assume is the bottom of the road surface (2%) which I don't want to show.
Is it also possible to label my side slopes as 4:1 instead of 25%?
View 4 Replies
View Related
Sep 25, 2012
I created a base drawing for sections that references an alignment. I xrefed in the drawing where my corridor was created. When I create the section views, the corridor shows up perfectly.
I then created a blank sheet and xrefed in my section view base drawing.In this sheet drawing, only parts of the corridors are visible.I have a C&G on one assembly and a shoulder on another assembly that aren't visible. (see pics)The first pic is my section base drawing.
View 3 Replies
View Related
Feb 23, 2012
When creating a Corridor Section Points Report using the Toolspace>Toolbox>Reports Manager in Civil 3D 2012, the stations get listed but only a few contain point information (see attached).
I am trying to generate stake-out data for a proposed road. I was able to get this report to work successfully in one of the Civil 3D tutorials, so I assume that nothing is wrong with the utility. The problem may be related to my corridor.
View 4 Replies
View Related
