I have created an existing ground surface...also 2 surfaces from corridors...one a road and 2 a berm. How do I merge these and get final contours of the proposed site after construction?
View 0 RepliesI'm trying to create an all new existing surface over existing ground. I have a TIN surface of the EG, and I have drawn overlay splines that describe the new surface, but how to go about creating that design surface.
It is a compound surface, open on one end and closed all around on the other, somewhat like a half of a football stadium, but with an irregular upper edge because I am needing to figure out cuts and fills to manipulate the EG into this new surface without costly major terraforming. There is about 40-50' vertical elevation between the "field" and the upper rim with a generally constant 7-10 deg. slope all around. I'm just at a loss to figure out how to approach this project, and am quite new to Civil 3D.
Civil3D 2013
MacBookPro 17 - 2.4GHz Intel QuadCore i7 (Late 2011 build)
Microsoft Windows 7 64bit
350GB Bootcamp volume
I have a rather large project for a roadway reconstruction. Therefore, the existing utilities are in a separate drawing and the existing ground surface model is in a separate drawing. All the above surface items (curb and gutter, asphalt, concrete, signs, sidewalks, landscaping, etc..) are in the master drawing. I then xref'd in my utility drawing and though I would use data shortcuts for my existing ground surface drawing. I took the surveyed triangles (3d faces) from our raw survey drawing and copied them into my surface drawing, created a surface from the triangles, created a boundary and such. So far everything is good. I created the working folder for the data shortcuts for this project and saved the drawing and closed it. I went into my master drawing and clicked on "Create Reference". I did not promote. The reference came though and everything is fine. Now I want to add contour labels in my surface drawing which I did but they do not show up in my master drawing but the contours themselves do. Do I have to promote this drawing into my master drawing so I can create the contour labels in my master drawing? I guess that is fine but the issue is we have small areas of topo that will be added as needed down the road. If I promote the surface drawing into my master drawing then when I add topo to the surface drawing, it wont update in my master drawing.
View 9 Replies View RelatedI have an existing ground surface with all different z co-ords and im trying to add three proposed buildings to my exisiting ground with all the builidngs having a level of 32.5 as a minimum, however at some points the ground is higher than 32.5 and I only want to raise my existing ground to 32.5 within the proposed buidling layout if it is below 32.5 as im doing a flood calculation. What do i need to for this?
View 2 Replies View RelatedI have a feature line as the top of a wall and want to grade up away from it to marry to existing ground.
View 1 Replies View Relatedhow to combine corridors and surface?
i make grading to surface, and make corridors,,,how to combine two segment?
While I was out, my partner somehow now has two existing ground lines in my cross-sections. ####exist and ####exist (1). They are offset by about .5 feet left to right. Where do I remove the surtface ###exst (1) from the cross sections. I am looking now.
View 2 Replies View RelatedI've worked with LDD for 11 yrs. Last week the IT guys changed my PC to Windows 7 64bit, so I can't have LDD and I have to work with C3D. so I am following software tutorials.
for designing a road I created:
alignment ---> surface profile ---> layout profile (project line) ---> assembly ---> subassemblies ---> corridor ---> set target surface and frequencies
Corridor is created with daylights ,but I don't see existing ground in corridor section editor.
There is nothing about this in tutorial. Also I don't know how to calculate the volumes, in LDD after this stage we could calculate the volumes. i think in C3D I should do more for calculation.
How to prepare for rendering Existing ground with cutted corridor river? Specially in places where corridor river is below EG. If there is some tool like cut?
View 4 Replies View RelatedI have an existing ground profile, and a design profile. All I want to do is label the slopes of the design. When I click my line label style and turn on the text it labels the existing ground and the design ground. I cannot find the setting in my two profile styles to turn the slopes off in the existing ground.
Oh, how can I get a tick on the V.C. dimension line?
I am trying to label existing ground & profile grade on my cross-sections the way old Land 4 used to do it. I've muddled through section view property style settings, band settings, group properties w/no luck. It can't possible be this difficult. What am I missing?
View 5 Replies View RelatedHow to get automaticly data on the profile. See my road profile in attachment.
Now i have to manually write data of elevation of existing and future ground and distance.
i think that is possible automaticly, but i dont know how.
I am just trying to compare a surface that was provided from a different survey company of the original ground of the borrow pit.
Although I used the same control I feel that there is something not matching with the elevations of the original ground provided and the outside of pit original ground measured this time. How do I check that the original ground is matching up in elevation?
I am trying to use AutoCAD to render some small parts. I am used to using Inventor Studio, but AutoCad's rendering tools have taken some getting used. to. I have everything figured out, with the exception of the ground plane for shadows and/or reflections.
I originally wanted a ground plane for a shadow to be projected on. However, I had no luck with that, so I modeled a large box under the part. Using that, I am able to get a shadow, or reflection, BUT, the edges of the box are showing in the background. The easy fix is to make the box larger, however, I need the reflective surface and background to be white so that it can be printed on paper without seeing the rendered edges.
How can I set a ground plane, or model a plane, for shadows or reflections, AND made it true white so that the edges cannot be seen?
I migrated from AC3D 2010 32-byte to AC3D 2012 64-byte recently. When I migrate my projects to 2012 and open the old 2010 drawings in 2012 I lose the surface lines out of my section sets. It doesn't seem to bother the profile views, only the section views.
Is there a way to work around this problem w/o having to regenerate the section views?
I am trying to add points into a surface. I have done this before without any problems, but now I am having issues.
When I ID points which makes up the surface it gives me the correct Z level e.g. 24.5m, however when I hover over the surface it shows me the surface name and a different z level e.g. 0.65m. What is the reason for this difference in z levels? I think this may be causing the issue I am having when I add new points.
I select the surface and use the 'edit surface command' in the ribbon, choosing add point.
When I add a point at the level I require(23.89m), it puts it in a lot higher than the surrounding area, so I tried to put the point in to the lower z levels (0.4m) it puts it in a lot lower!
My goal is coming up with the volume bounded by the design surface and the existing surface. I don't have the design surface modeled yet.
Do i need to create alignment offsets?. Alignment 1 profile view is also attached. Then Alignment2.
What about starting with alignment1 profile view? Since I have created a polyline as the design profile ?
how do I shrink labels? Where is it in the settings ; the Align folder had been check.
Im currently using an addon for Civil 3D called Novapoint. It allows me to create 3D models of surfaces made out of 3d faces and easily models cut and fill 3d-models for me.
The only thing i need to create a cut and fill model is one or several ground surfaces (existing ground, earth layers, rock etc. whatever i need) and a closed polyline/3Dpolyline that represents the level I want my cut and/or fill model.
I enter the spcifications I want such as; earth cut angle, rock cut angle, fill angle, select which surfaces i want to include in the model calculation and select the polyline.Novapoint then calculates the cut/fill model from the surfaces to the polyline and models the different cut/fill angles and gives me the results in a 3d-face model and a specification of the volyme of rock cut, earth cut an fill.
1. Novapoint is quite unstable and crashes alot
2. You cant create profiles out of 3d faces
3. Novapoint does not automaticly combine the start surfaces with the modeled cut/fill surface
4. A large surface made out of 3d-faces demands alot of computer power
So I want to how I do the same that Novapoint does for me in Civil 3D? (I have access to Civil 3D 2007-2013 depending on which one you're using)I know I can take the 3Dfaces i created in Novapoint and make a surface in Civil 3D with them but I want to exclude Novapoint completely.
Some background: We have a composite surface of existing surveyed contours as a TIN pasted into existing aerial contours that we received from a client. We used polylines to generate our proposed contours, and then generated a proposed surface from that. We've made a blank surface, pasted in the existing surface, and are trying to paste in our proposed surface... only the existing contours outside of the proposed suface no longer line up correctly once we do.
We've tried applying the method laid out here: [URL] ........ (and the link referenced in the bottom) but are still having trouble getting the surface to work. We've tried offsetting as little as 0.25' and as much as 5' with the feature line draped over the existing surface, but it seemed that the greater the offset, the greater the discrepancy.
Just to make sure we even tried that correctly - should the breaklines that we add be standard or non-destructive? (I've tried it both ways with little success either way, so I don't know if it matters much in this instance, but perhaps for future reference it would work.)
I've attached a screen shot of our surfaces. The pink and green lines are the proposed contours, the white dashed are the existing. The outer red line is offset 0.25'. As I've mentioned, we've tried offsetting various amounts with decreasing success.
When pushing F1 for help in 2012 Civil 3D regarding this feature, it takes me to a page about migrating custom files over.
It says to copy the pipe/structure files over, then to open up Civil 3D and type in PIPECATALOGREGEN. Well, it doesn't work and says that it is an unknown command.
Civil 3d 2014.... I have existing surface and a profile with 5 sample lines. All of them are good except 1 sample offset. I can do I quick profile and the profile looks like it should but if I generate an actual profile 90% of the profile is off. I have already tried reoding the alignment but it looks same on either one.
View 2 Replies View RelatedHow to rename the existing profile “profile from surface”? On the right click there is no such option!
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
I have been given a survey on AutoCAD which was orginally 2D with the levels written in text next to it. I changed each point (690) to include the level in the Z-direction. I am trying to calculate volumes of topsoil removal and then cut anf fill volumes.
So I opened up Civil3D in metric template and imported my drawing as I have not been given a ddata file with the co-ordinates. Unfortunately I am having trouble creating a surface between the existing points.
I have a surface that I created by joining to surfaces, and now I want to reduce my boundary, how can I edit it?
windows 7, intel I7, 8 MB RAM, civil3d 2013.
I have a survey of an existing road surface and need to show where water will collect (pond). I can obviously use the water drop function and show where water will flow over the surface, but what I need to show are the resultant pond extents on the surface.
View 3 Replies View RelatedI have an existing surface and I need to creat a surface using contour lines of a at the high point on a spillway to the bottom of my pond to calculate volumes. How do I do this?
AutoCAD/Survey Tech
Merritt LS L.L.C..
743 Horizon Ct. Suite 100B
Grand Junction, CO 81506
I am having some trouble creating a TIN from a point layer in Civil 3D 2011. Would the best course of action be to extract the points from the drawing and creating a surface from there, or is there a way to create the TIN around the existing points in Model space?
I'm much better versed in AutoCAD, but excited about furthering my understanding with Civil3D.
I don't undrstand why my assembly line increased after the existing surface in cut and fill condition, it should be stop at the existing surface. due to this problem my cut and fill quantities is not coming accurate. I'm attaching the screens shot of section. I'm using civil 3d 2009 32 bit software.
View 4 Replies View RelatedI have an existing surface with a steep slope and a feature line for the edge of a proposed walkway. I need a buffer of 25m on either side of the walkway but offsetting doesn't take the grade of the slope into account. How do I grade down the hill from the feature line at 25m to match to the existing surface?
View 3 Replies View RelatedEvery week I recieve new survey data (typically around 20 points) to insert onto an existing surface of our local landfill.
The surface is displayed as minor and major contours. The new survey data typically always has higher elevations then the exist surface and shot roughly 2 meters apart.
Here's my issue...when the survey data is inserted and the surface is rebuilt, the contours seem to turn into little cones at each new point. see attached...
how to eliminate these 'cones' so the surface contours seem more relistic?
I am trying to create a localized existing surface from a very large topo. I promoted the existing surface shortcut into my drawing, then created a cropped surface to be put in a new drawing. After creating the cropped surface the new file shows that a surface has been created, however, the surface contains no data. I am using c3d 2012.
View 1 Replies View Related