AutoCAD Civil 3D :: Why Assembly Line Increasing After Existing Surface
Dec 15, 2013
I don't undrstand why my assembly line increased after the existing surface in cut and fill condition, it should be stop at the existing surface. due to this problem my cut and fill quantities is not coming accurate. I'm attaching the screens shot of section. I'm using civil 3d 2009 32 bit software.
I have an existing surface with a steep slope and a feature line for the edge of a proposed walkway. I need a buffer of 25m on either side of the walkway but offsetting doesn't take the grade of the slope into account. How do I grade down the hill from the feature line at 25m to match to the existing surface?
I'm trying to create an all new existing surface over existing ground. I have a TIN surface of the EG, and I have drawn overlay splines that describe the new surface, but how to go about creating that design surface.
It is a compound surface, open on one end and closed all around on the other, somewhat like a half of a football stadium, but with an irregular upper edge because I am needing to figure out cuts and fills to manipulate the EG into this new surface without costly major terraforming. There is about 40-50' vertical elevation between the "field" and the upper rim with a generally constant 7-10 deg. slope all around. I'm just at a loss to figure out how to approach this project, and am quite new to Civil 3D.
Civil3D 2013 MacBookPro 17 - 2.4GHz Intel QuadCore i7 (Late 2011 build) Microsoft Windows 7 64bit 350GB Bootcamp volume
I am trying to add points into a surface. I have done this before without any problems, but now I am having issues.
When I ID points which makes up the surface it gives me the correct Z level e.g. 24.5m, however when I hover over the surface it shows me the surface name and a different z level e.g. 0.65m. What is the reason for this difference in z levels? I think this may be causing the issue I am having when I add new points.
I select the surface and use the 'edit surface command' in the ribbon, choosing add point.
When I add a point at the level I require(23.89m), it puts it in a lot higher than the surrounding area, so I tried to put the point in to the lower z levels (0.4m) it puts it in a lot lower!
Im currently using an addon for Civil 3D called Novapoint. It allows me to create 3D models of surfaces made out of 3d faces and easily models cut and fill 3d-models for me.
The only thing i need to create a cut and fill model is one or several ground surfaces (existing ground, earth layers, rock etc. whatever i need) and a closed polyline/3Dpolyline that represents the level I want my cut and/or fill model.
I enter the spcifications I want such as; earth cut angle, rock cut angle, fill angle, select which surfaces i want to include in the model calculation and select the polyline.Novapoint then calculates the cut/fill model from the surfaces to the polyline and models the different cut/fill angles and gives me the results in a 3d-face model and a specification of the volyme of rock cut, earth cut an fill.
1. Novapoint is quite unstable and crashes alot
2. You cant create profiles out of 3d faces
3. Novapoint does not automaticly combine the start surfaces with the modeled cut/fill surface
4. A large surface made out of 3d-faces demands alot of computer power
So I want to how I do the same that Novapoint does for me in Civil 3D? (I have access to Civil 3D 2007-2013 depending on which one you're using)I know I can take the 3Dfaces i created in Novapoint and make a surface in Civil 3D with them but I want to exclude Novapoint completely.
Some background: We have a composite surface of existing surveyed contours as a TIN pasted into existing aerial contours that we received from a client. We used polylines to generate our proposed contours, and then generated a proposed surface from that. We've made a blank surface, pasted in the existing surface, and are trying to paste in our proposed surface... only the existing contours outside of the proposed suface no longer line up correctly once we do.
We've tried applying the method laid out here: [URL] ........ (and the link referenced in the bottom) but are still having trouble getting the surface to work. We've tried offsetting as little as 0.25' and as much as 5' with the feature line draped over the existing surface, but it seemed that the greater the offset, the greater the discrepancy.
Just to make sure we even tried that correctly - should the breaklines that we add be standard or non-destructive? (I've tried it both ways with little success either way, so I don't know if it matters much in this instance, but perhaps for future reference it would work.)
I've attached a screen shot of our surfaces. The pink and green lines are the proposed contours, the white dashed are the existing. The outer red line is offset 0.25'. As I've mentioned, we've tried offsetting various amounts with decreasing success.
Why can't Inventor constrain an ellipsoidal contour with a line? We have pressure cylinders which uses a 2:1 ellipse. These cylinder get welded to a base stand fixture. The surface of the ellipse nestles in between contact points of the base stand, in this case lines of geometry. Yet Inventor can't constrain them as such. Any good workflow (at the assembly level) so that we don't have to ground components and use the Analyze Interference tool to make sure we are right on the surfaces? I don't understand why it will work for a cylindrical surface but not an elliptical surface.
Civil 3d 2014.... I have existing surface and a profile with 5 sample lines. All of them are good except 1 sample offset. I can do I quick profile and the profile looks like it should but if I generate an actual profile 90% of the profile is off. I have already tried reoding the alignment but it looks same on either one.
I have been given a survey on AutoCAD which was orginally 2D with the levels written in text next to it. I changed each point (690) to include the level in the Z-direction. I am trying to calculate volumes of topsoil removal and then cut anf fill volumes.
So I opened up Civil3D in metric template and imported my drawing as I have not been given a ddata file with the co-ordinates. Unfortunately I am having trouble creating a surface between the existing points.
I have a survey of an existing road surface and need to show where water will collect (pond). I can obviously use the water drop function and show where water will flow over the surface, but what I need to show are the resultant pond extents on the surface.
I am having some trouble creating a TIN from a point layer in Civil 3D 2011. Would the best course of action be to extract the points from the drawing and creating a surface from there, or is there a way to create the TIN around the existing points in Model space?
I'm much better versed in AutoCAD, but excited about furthering my understanding with Civil3D.
I've got several assemblys built for a road project. the problem is whenever i modify an assembly by adding a subassemby, some of the existing subassemblies move. they stay attached to the assembly but they disconnect from the part they were attached to. i can move them back so the assembly looks correct but when i rebuild the corridor chances are they show up wrong. i've tried 'move to' and just grabbing and snapping. i can eventually get it attached but not without trial and error. i'm running c3d2012.
Dell Studio XPS 9100 Intel Core i7 CPU 930 @ 2.8GHz 12GB Ram 64 bit C3D 2012 SP3.0
I have a rather large project for a roadway reconstruction. Therefore, the existing utilities are in a separate drawing and the existing ground surface model is in a separate drawing. All the above surface items (curb and gutter, asphalt, concrete, signs, sidewalks, landscaping, etc..) are in the master drawing. I then xref'd in my utility drawing and though I would use data shortcuts for my existing ground surface drawing. I took the surveyed triangles (3d faces) from our raw survey drawing and copied them into my surface drawing, created a surface from the triangles, created a boundary and such. So far everything is good. I created the working folder for the data shortcuts for this project and saved the drawing and closed it. I went into my master drawing and clicked on "Create Reference". I did not promote. The reference came though and everything is fine. Now I want to add contour labels in my surface drawing which I did but they do not show up in my master drawing but the contours themselves do. Do I have to promote this drawing into my master drawing so I can create the contour labels in my master drawing? I guess that is fine but the issue is we have small areas of topo that will be added as needed down the road. If I promote the surface drawing into my master drawing then when I add topo to the surface drawing, it wont update in my master drawing.
I needed to remove a feature line that I used as a break line when creating a surface. When I removed the feature line from the definition of the surface, the grading did not change. It appears the points created by the feature line remain which is why grading didn't change. The only work around was to delete these points.
I noticed the same thing happens when I removed the surface boundary and inserted a new boundary. why these points remain and how to remove when I delete boundary and feature line from surface?
I am trying to create a localized existing surface from a very large topo. I promoted the existing surface shortcut into my drawing, then created a cropped surface to be put in a new drawing. After creating the cropped surface the new file shows that a surface has been created, however, the surface contains no data. I am using c3d 2012.
I have a proposed surface that has been made by selection polyline with a z elevation as contours. Is it possible to have civil 3d easily change the weeding and supplementing factors to a tighter value after it has already been made?
if i want to target the existing surface beyond the edges of my road/sidewalk, should i use the link slope to surface subassembly at both ends? i want the model to test if in a cut or fill situation, and then target.
I need to create an assembly that will give me the volume of a new shoulder along an existing road, as show in this picture.
I can easily make an alignment along my edge of pavement, and match the existing elevations, but I need to hold the cross slope constant AND the shoulder slope constant, and have the bottom of the shoulder slope to a target 2 feet off of my ROW.
So we have to adjust the elevation of hundreds of drainage structures from their existing elevation to the new finished ground elevation.I know we can give this information within the structure label by adding a reference surface but we would like to produce a table with three columns:
Structure No. Existing Rim Elev. Proposed Rim Elev.
I have a bunch (hundreds, so manual input not an option) of X,Y points without elevation data that I would like to import into a DWG and assign an elevation that is based on an existing surface object. Is there a way to do this for a point file? The command for inserting individual points would be the "Create points - Surface > Random" but I don't see a way to do this in a batch type method where i have my PNE formatted input file to just move the points to sit on the existing surface.
i have a corridor. the corridor feature line that is supposed to hit the proposed centerline is following my existing grade instead of where the profile is. in other words, the corridor line i need at the centerline when i do "feature lines from corridor" is following my existing grade instead of the top of my road. did i accid. change something? i need it to follow the top centerline of my road. the red arrow is the line i need at the top centerline.
I'm looking for the best way to create a separate assembly out of various component parts in an existing assembly so that the whole thing can be placed in an assembly as you would a part, I know it's possible to demote components within an assembly but are there any other methods similar / better ?
When I paste the proposed surface with the corriodor surface and I check the profile the proposed surface ties to the bottom of the kerb ignoring the footpath.Also in the same drawing file I can't seem to export it to ACAD.
While I was out, my partner somehow now has two existing ground lines in my cross-sections. ####exist and ####exist (1). They are offset by about .5 feet left to right. Where do I remove the surtface ###exst (1) from the cross sections. I am looking now.
Bring that back from the archives... because I am still very fond of redoing hundreds of cross sections because you're incable of redistributing the graphs when a sample line is added to a an existing group... and blow up all of the projections well done.... way to leave out a super critical dynamic component.
PPD E P I C F A I L
There is some unbelievable gaps in the software but how do you let this one go on for so long?
Dell Precision T3500 - Xenon W3550 @ 3.07 (4 core) Ram @ 12Gb 64bit Win7 Pro Samsung SSD NVIDIA Quadro 2000 - Dual Monitors Cat 6 network with GlobalScape Avail Agent - WAFS Infrastructure Design Suite Premium and Civil 3D 2012