When I paste the proposed surface with the corriodor surface and I check the profile the proposed surface ties to the bottom of the kerb ignoring the footpath.Also in the same drawing file I can't seem to export it to ACAD.
View 1 RepliesI have created a new assembly that uses a HMA dike rather than your typical curb but my surface always begins at the top of the HMA pavement rather than the top of the curb subassembly. See Picture. Where's the setting to fix this (is it a daylight setting) or it is a bigger problem in that I didn't create the subassembly or assembly correct to begin with?
Win7 (x64), EVGA 790i, 8GB RAM, EVGA 8800GT, 250 GB iSSHDD, & RAID 0/1
I would like to have my corridor section points report to have different labels for the points like Edge of Shoulder or EOP instead of labels like P2 and Hinge. Is the only way to do this to somehow change the codes in the stock subassemblies?
Civil 3D 2014
I had a proposed surface in Civil3D2010 that was fine, made revisions to the proposed contours using grips or deleting/adding contours. Now when I try to add the new contour data to the surface either the program hangs up or I get contour error messages and the surface never gets re-built.
View 1 Replies View RelatedThe engineers at my company digitize proposed contours in a drawing and then they want me to create a surface out of the contours....the contours usually are 2 foot contours with areas that the software tends to translate based on the contours that I selected to create the surface.....I then usually need to create a profile, which does not look accurate compared to the contours, such as low spots etc...............
My question is since the engineers at my work do not how to use the software, and I am not an engineer, making the profile look a certain way sometimes needs to be tweeked by me.... How to alter the proposed surface?I am pretty sure that feature lines cannot cross contours that I have selected to create the surface?
I have created a surface from a corridor. I set the boundary of the surface to the daylight of the corridor. In some areas of the corridor the surface does not triangulate see attached.
View 2 Replies View RelatedMy corridor surface is not matching my corridor top links. see attachments. this is affecting my volumes!
The section-plan(surface red).png is showing the section editor and the plan view. the red highlighted line in section is the corridor surface and as you can see in plan view the surface is incorrect and wiggly.
The pdf is all my sections with the red linework being the corridor surface.
C3D ver 2012
Win 7, 64bit
I have a existing surface. I want to create a proposal surface so I can know the volume between boths. This proposal surface is represent for a disposal area that can be filled up to a elevation. I have a bottom of P-surface as a feature line at EL 1608, and I want top of P-surface to EL 1613.
View 4 Replies View Relatedattached is Roadway.dwg file
I made "Road" surface from Corridor Properties / Surfaces... but when I go to surface properties for "Road"...the statistics tab is blank.
2013 Civil 3D
I'm trying to create a proposed grade surface using the grading tools. I drew the outline boundaryof the proposed surface as a closed polyline then created a feature line from it and assigned different elevations to it. When I try to select the feature line in order to create the grading, I get "THIS FEATURE OVERLAPS ITSELF AND CANNOT BE GRADED". What could be a possible reason for this?
View 5 Replies View Relatedcustom sub-assembly codes,I have gone through the list of codes that is given in the code list.
1. How do I add new code, should I just add with the new index at the end
2. What all things I need to update so correct feature line is picked, etc
3. Any c# example of building a sub-assembly using .net.
So we have to adjust the elevation of hundreds of drainage structures from their existing elevation to the new finished ground elevation.I know we can give this information within the structure label by adding a reference surface but we would like to produce a table with three columns:
Structure No. Existing Rim Elev. Proposed Rim Elev.
How to produce such a table?
I'd like to view the point codes (and also the links and shapes) of an assemby I have on my c3d drawing.I dont see nothing to get it ....
Civil 3D (2013)
I have a problem with point codes in section views in civil3d 2013. They are not showing at all. Drawing was made in civil3d 2012 and all point codes with defined styles were displayed correctly in section views and now they are all gone. Just link codes are shown. Is there something in setup of code styles that has to be changed?
Even if i set up new code and new label style it does not show up in section view after rebuild. Just in assembly.
If i do the same for link label it does show both in assembly and in section views.
all of a sudden whenever I run audit on my corridor file the surface definition becomes a snapshot. To add to the drama, the corridor surface will not paste into an empty surface. Why?
View 2 Replies View RelatedI often have to do storm pond surfaces that (for the purposes of planning) are flat on the bottom. These surfaces are created from a combination of survey data and grading groups and the tin of these surfaces is perfectably acceptable. However, when contours are shown, the flat bottom is shown with contours jig-jagging all over the place.
The attached image shows a comparison of the same pond. The top was created with survey data and grading groups; the bottom was created using contour data only. The generated surface on the top shows the bottom contour going in different directions and has parts where the an expected contour is missing.
How to correct/manipulate the surface to show a proper flat surface?
My problem added with pic ... I want to make volume calculate for sample road project. When I try to compute materials I cant use Corridor surface for DATUM... There is only target surface on option..
View 2 Replies View RelatedI am trying to visualize a road project. The problems is, whenever the corridor surface goes below the EG surface (when the road is in cut) the EG surface is the only visible surface.
I sort of need to subtract the corridor surface from the EG surface, or merge the both surfaces into one.
I have a profile showing proposed storm sewer, existing sanitary, rock surface, existing surface, and proposed profile. Today for some reason the proposed profile and labels, and the existing surface are not showing on the profile and I'm not sure what has changed or how to get them back.
View 3 Replies View RelatedWe have an engineer who is taking an existing surface and wants to show a proposed road 2" higher than existing.
I told him to simply adjust his assembly for his corridor to account for the 2" difference, but the County agency needs to see a profile.
My questions:
1) Is there a way to easily copy a profile made from a surface and "convert" it to a proposed profile? If we copy and explode, it turns into hundreds (thousands?) of tiny pline segments and it would be a mess to convert all those to a profile 1 by 1. If we make the corridor, and choose "profile from corridor", we do not have an option that could be used to represent the centerline.
2) Other than loss of dynamic updating), would it make sense to adjust the assembly so the top surface would be accurate, then copy the profile, explode the copy to a block and simply shift that (as essentially basic linework)?
When i try to create a material list, i don't see my corridor surface - just the EG surface appear in the list.
View 2 Replies View RelatedI am creating a corridor with a simple assembly. On my assembly, I have basic lane and daylight Multiple surface. My target is existing ground.
View 9 Replies View RelatedI want to add different assemblies (some with walls or ditches) along the same corridor at given stations
Can that be done?
1. Attached is a file , when opened show two viewports. the plan view look OK , but the ortho on the right show a corridor not near elev. Of the the alignment and the surface is missing ( I cannot get to the object viewer to show me the model setting) .
Am I in big trouble and had to create a surface again?
2. The end of this corridor you have lines all over the place , I probably need to create a corridor surface , correct?
3. Why is the alignment so far from the corridor model?
I have created a corridor of an exit ramp. Part way through the corridor, the left side slope isn't generated.
The subgrade doesn't exist. In the Sideslope to no side slope.png image that the corridor has a side slope and ditch at 10+600. Also in the 10+600.png image. But at 10+610 there is no side slope. There is OG surface out far enough, but it seems that in the 10+610.png image that there isn't enough OG surface. Orignally there was survey data missing in this area and it was added after the fact to the OG surface. Why doesn't the corridor recognize it, if that is the case. I have updated and syncronized the heck out of everything, but it still doesn't seem to work.
I should point out that this is in meters (the cross sections are 10m apart) and that it is the same Assembly being used for this area. Also all targets are consistant through this area as well.
I am trying to create a surface from a corridor. I have a sub-assembly attached, which I believe is working correctly. I managed to create the empty surface and when I try to add surface data nothing seems to happen. I keep changing the specified code to Base which is my finished gravel structure and hit the + but again nothing seems to happen.
Ultimately I am trying to determine a volume between my corridor and original topo.
I am having some issues with my corridor. It is for a 1.5 mile two lane section of highway. When I created the corridor, I used 15 assemblies. Now, when I try to create a corridor surface, I have issues. The file crashes when I try to load the surface.
View 2 Replies View RelatedI have one corridor with several baselines. I have asked it to generate a corridor surface but it has left out several baselines from the surface. I have ruled out assemblies. I am not sure what is going on. I am also unable to get feature lines from this portion of corridor as well. The corridor builds just fine and I can see what the daylight lines are etc. What's going on. Yes I have audited the drawing.
View 2 Replies View RelatedAfter you go thru and setup all of the links and feature lines that you want to use to create a corridor surface, is there any way to save that particular setup to be used on other corridors? That way you would not have to select all of them again and again, every time that you wanted to create, say a datum surface.
View 1 Replies View RelatedWhen I create a corridor surface I usually create a suface boundary automatically by daylight.Half the time this works fine, half the time it doesn't work at all. If I view the corridor in 3d view it looks fine.
I tried to create a shrinkwrap polyline to use as a boundary but when I picked the corridor in the shrinkwrap command
it locked up my computer. These are just simple corridors with no intersections. Why the automatic boundary only works intermitently? Is there a better/easier way to create the surface boundary?
I created a surface corridor, called STAGE 1, that I would like to target with a second corridor, STAGE 2. In a new file, I data referenced in STAGE 1 surface. It is showing up as an option for me to use as a target in my STAGE 2 corridor properties. Once I look at my sections it shows there is nothing targeted on that side.
View 1 Replies View Related