I have a profile showing proposed storm sewer, existing sanitary, rock surface, existing surface, and proposed profile. Today for some reason the proposed profile and labels, and the existing surface are not showing on the profile and I'm not sure what has changed or how to get them back.
View 3 RepliesWe have an engineer who is taking an existing surface and wants to show a proposed road 2" higher than existing.
I told him to simply adjust his assembly for his corridor to account for the 2" difference, but the County agency needs to see a profile.
My questions:
1) Is there a way to easily copy a profile made from a surface and "convert" it to a proposed profile? If we copy and explode, it turns into hundreds (thousands?) of tiny pline segments and it would be a mess to convert all those to a profile 1 by 1. If we make the corridor, and choose "profile from corridor", we do not have an option that could be used to represent the centerline.
2) Other than loss of dynamic updating), would it make sense to adjust the assembly so the top surface would be accurate, then copy the profile, explode the copy to a block and simply shift that (as essentially basic linework)?
Civil 3d 2014.... I have existing surface and a profile with 5 sample lines. All of them are good except 1 sample offset. I can do I quick profile and the profile looks like it should but if I generate an actual profile 90% of the profile is off. I have already tried reoding the alignment but it looks same on either one.
View 2 Replies View RelatedHow to rename the existing profile “profile from surface”? On the right click there is no such option!
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
I have the profile of my pressure network and storm crossings converted into ellipses but I can't get my surface to show on the profile to show the amount of cover I have between the existing ground and top of pipe.
View 1 Replies View RelatedI have 3 profiles that I've superimposed together. Then I created sheets using the superimposed profile. I used the wizard and had Civil 3d do it for me (2012). Now I have to add a 4th profile to the mix and get it to show in my profile views that have already been cut. The data is shortcut into the drawing with my cut profiles views. How do I get it to be in the cut profile views without re cutting everything?
View 1 Replies View Relateddifferences in elevations of points along Profile 2 (the proposed new road elevation) and Profile 1 (the existing elevation/surface) should be computed and shown right above the Profile 2 line. For example, if at a certain point PT 1 the elevation of the proposed road is 132.44 meters and the elevation of the existing surface is 132.45 meters, the difference is -0.01 meters and it should be shown exactly above the Profile 2 line (or a little bit above it) but not on it. The same should be done for every chosen point along the proposed profile.
So far, I have done this manually, by dragging the difference (already automatically computed and shown in one of the bands below the profiles) to the correct place for every single point. However, I don't know how to do this automatically.
Im creating a Profile Bandset and would like to have multiple surface/profile elevations shown, ie: EG, FG, Back of Curb and Back of walk. While creating this bandset I see that the text component editor properties only has code for profile 1 elevation and profile 2 elevation in the properties area, which the code for this looks like below.
<[Profile1 Elevation(Uft|P2|RN|Sn|OF|AP)]>
<[Profile2 Elevation(Uft|P3|RN|AP|Sn|OF)]>
Ive tried to write my own code using the profile 2 as an example but it doesnt seem to work as a 3rd surface/profile and only seems to mimic the profile 2 elevation when placed in the band
My questions are as follows
1) does Civil 3d only allow 2 surface elevations in any band set? if it does allow more profiles/surface elevations what am i missing to create it?
2) if Civil 3d does alow for multiple surfaces to be shown in the band set how do i get the text component editor to supply the extra profile elevation codes? or would i need to create from scratch
3) if i need to write the code from scratch does any listing of the codes and meanings of each code ie what does RN, Uft, Sn and so forth do and mean .
Attached are survey points that created the surface of a road embankment portion that caved-in. The road is very near a reservoir shoreline.
1. How can a surface profile be produce? I/'ve use line to change it into an alignement and then create a proile , then a profile view. But the the surface profile is missing.
2.the points having higher elevation are the top edge( road level) of the cave-n . A few few shots were take before the shorline elevations.
3. What the best way to come up with the rock volume to fill the cave-in given this surveying points., Also the shoreline elevation will be lowered some more while work is being done since the fill is not allowed to fall in the reservoir.
So we have to adjust the elevation of hundreds of drainage structures from their existing elevation to the new finished ground elevation.I know we can give this information within the structure label by adding a reference surface but we would like to produce a table with three columns:
Structure No. Existing Rim Elev. Proposed Rim Elev.
How to produce such a table?
I am working on a corridor. I have a proposal profile, and now i wanted to add a vertial curve between the new profile and exsiting. (see attached.) but i have not done before.
View 4 Replies View RelatedI'm currently working on a profile and I just don't understand why my profiles barely show any stations. It doesn't even show the very first station. I remember checking on a box that mentioned showing the 1st station and still nothing. I've gone into the edit band style and turned on the labels at minor stations but it just turned on the FG/EG elevations.
I've added a picture showing what i'm talking about. It only shows stations 31+00 and 32+00. Not 30+00 or the 50' increments. Also, while I'm on the subject. How do I get something proposed into this existing profile to show FG Elevations. Example if I just wanted to strike a straight line from 30+00 to the end where the elevation is a 91' & 86'.
HP Compaq 8100 Elite
Win 7 Pro SP1 - 64Bit
8GB RAM
i7 860 @ 2.80 GHZ
AutoCad Civil 3d 2012 SP1
I am fairly new to the Civil side of AutoCAD, as I used to work primarily in Map. I am working on a street rehab project in which I need to take survey points showing existing elevations (centerline, flowline, and top of curb) and show existing profiles in a profile view. I have no problems setting up the profile view(s) or the centerline alignment, but I am having problems with creating the profiles themselves, and I have a two part question about them
Question 1: According to the user's guide, the correct way to set up an "existing" profile is by extracting it from a surface, but I don't have a surface to use. In reading through the various profile types, the best way to set up what I want seems to be by using the profile layout tools, but the help says that a profile layout is supposed to be for a final "proposed" profile, not the existing. Does this actually matter? Will I be breaking Civil functionality by creating an existing profile using the profile layout tools?
Question 2: In reading through the profile layout tools, everything seems to be centered around PVI's. Even using the "tangent tangent" method to add in points seems to only use the first and last point as controls, with everything in between treated as a PVI. If you look at the documentation here, points one and four are treated as actual elevations, while curvature occurs at points 2 and 3. In my case, since what I have is a series of actual points on a surface, each point should be an actual surface elevation with curvature occurring between points and not at them. What method should I be using to input the points in the profile?
I have one surface "EG" and two alignments, I'll call 1 and 2. The profile view already has the alignment 1 surface projected on it. I go to profile>Create Surface Profile and select alignment 2, Surface EG, go to ADD it but the profile list is empty. Shouldn't it already be populated with alignment 1 and all I'm doing is adding 2 to it? Both alignments are in the same site.
View 4 Replies View RelatedI can’t seem to manage to get the profile working, the assembly seems to look ok but it doesn’t show on the profile!
The assembly just follows the line of existing ground and does not show the height of the assembly (barrier). Also, if you take a quick section through the alignment/corridor it shows the assembly but doesn’t show it fully?
In highway construction, I usually check for lowest ditch elevation and see how the existing drainage flows. Typically one would create or specify in CL profile creation with a 15m offset right and left which would then generate existing CL and 15m offset profiles in profile view. However, the 15m offset profile might not represent the lowest point in the ditch as the lowest elevation offset distance varies along the highway.
My question: Is there a way in civil 3D profile creation where it can automatically trace the lowest elevation in the ditch and plot it in profile view?
I have an existing ground profile, and a design profile. All I want to do is label the slopes of the design. When I click my line label style and turn on the text it labels the existing ground and the design ground. I cannot find the setting in my two profile styles to turn the slopes off in the existing ground.
Oh, how can I get a tick on the V.C. dimension line?
I have alignments that go in and out of a surface boundary (this is because I have a surface that represents the bottom of pavement.) I want to show the surface profile with the gaps in the profile view (where there is no surface. However in the profile view the gaps are sometimes connected with a straight line instead of being blank.
How can I have a surface profile represent the bottom of pavement properly? (An alignment that is not fully withing the surface boundary.) I know I could add the profile multiple time with different start/end stations But, I don't want that, I want it to be dynamic, as the alignment will change.
I'm currently making a profile view where i want my features/objects to be shown in the bands for chain age elevation etc.
I have fences footpaths & vegetation lines that i can show in my profile view by 'projecting objects to profile view', but i was wondering if I could show these in the bands instead as it would be more convenient.
From what i can see in my bands I can label at Major Stations, Minor Stations, Horizontal Geometry Point, Vertical Geometry Point, Station Equation & Incremental Distance.
I've attached a picture showing what it currently looks like.
[URL]...........
I have created a pipe network and a couple of the manholes have laterals coming in at 90 degrees to the main line. I haven't been able to get these to show up in my profile views although they are listed in the manhole invert labels.
View 9 Replies View RelatedI am trying to label existing ground & profile grade on my cross-sections the way old Land 4 used to do it. I've muddled through section view property style settings, band settings, group properties w/no luck. It can't possible be this difficult. What am I missing?
View 5 Replies View RelatedWhat do I draw the existing pipes as that will be under the surface that I'm profiling? I have the surveyed invert points I'm assuming that won't be polylines? how to get the pipe to show at the proper elevation on the profile?
View 2 Replies View RelatedHow to get automaticly data on the profile. See my road profile in attachment.
Now i have to manually write data of elevation of existing and future ground and distance.
i think that is possible automaticly, but i dont know how.
I have a surface profile which has 2 surfaces in it. The surfaces overlap, and where there is overlap I just want to show one surface. Right now it looks like I'm going to have to smack a new boundary on the one surface to clip it, but I thought there might be a way to limit the display range of one surface in the profile.
Right now, I've only figured out how to do this so both surfaces are limited to the same range, but I can't figure out how to do it if you want to just control the range displayed of one surface and show all of the other surface.
I have a profile with an eg surface and a fg surface made from design tool. Now I want to import a proposed surface in there too.
View 4 Replies View RelatedI Created a profile from existing surface and created a layer called "PRO-EXISTING" and set linetype to "HIDDEN". I also set my standard style to display linetype "BYLAYER" but my dashes are not even like polylines when plinegen is "ON"
View 4 Replies View Relatedi need to transition from a proposed to a future linetype part of the way down my profile. It's the same surface, just that @ station XX+XX.XX it becomes future. I need it a diff linetype to faded back, for example. Is there a way to do that? I'm thinking my only option is two create two surfaces, one propsed and one future. My situiation currently is that I already have one complete surface and would like to know if it's possible.
View 9 Replies View RelatedI have a drawing with surface profiles and the linetype generation is working on some and not the others. They're all dynamic and they're not dref'd in and like I said, a few with the same style look correct and a few are incorrect.
C3D 2012
I have modeled a storage pond on my site and I have the existing surface hidden for the extent of the pond.
Is there a way to make that hidden existing surface, show up on the profile view?
I have attached images to better explain myself.
I am working in C3D 2012.
A way to associate a default profile style with a surface. In other words, I would like to set a different default profile style for each surface. Same could be true for sections.
View 6 Replies View RelatedI have a drawing with multiple profiles. We originally had an existing and finished ground surface in the drawing, but decided to use a data shortcut to the surfaces as the design kept changing. We deleted the old surfaces from the drawing, and created the data references, using the same surface names for the new referenced surfaces.
The ground lines show up in the profile, but I can't get it to show the linetype I need for the EG surface (dashed). It doesn't act like a typical profile line - it now shows a lot of PVI points, and plinegen settings have no effect.