I have a profile showing proposed storm sewer, existing sanitary, rock surface, existing surface, and proposed profile. Today for some reason the proposed profile and labels, and the existing surface are not showing on the profile and I'm not sure what has changed or how to get them back.
Civil 3d 2014.... I have existing surface and a profile with 5 sample lines. All of them are good except 1 sample offset. I can do I quick profile and the profile looks like it should but if I generate an actual profile 90% of the profile is off. I have already tried reoding the alignment but it looks same on either one.
I'm trying to create an all new existing surface over existing ground. I have a TIN surface of the EG, and I have drawn overlay splines that describe the new surface, but how to go about creating that design surface.
It is a compound surface, open on one end and closed all around on the other, somewhat like a half of a football stadium, but with an irregular upper edge because I am needing to figure out cuts and fills to manipulate the EG into this new surface without costly major terraforming. There is about 40-50' vertical elevation between the "field" and the upper rim with a generally constant 7-10 deg. slope all around. I'm just at a loss to figure out how to approach this project, and am quite new to Civil 3D.
Civil3D 2013 MacBookPro 17 - 2.4GHz Intel QuadCore i7 (Late 2011 build) Microsoft Windows 7 64bit 350GB Bootcamp volume
I am trying to add points into a surface. I have done this before without any problems, but now I am having issues.
When I ID points which makes up the surface it gives me the correct Z level e.g. 24.5m, however when I hover over the surface it shows me the surface name and a different z level e.g. 0.65m. What is the reason for this difference in z levels? I think this may be causing the issue I am having when I add new points.
I select the surface and use the 'edit surface command' in the ribbon, choosing add point.
When I add a point at the level I require(23.89m), it puts it in a lot higher than the surrounding area, so I tried to put the point in to the lower z levels (0.4m) it puts it in a lot lower!
I have 3 profiles that I've superimposed together. Then I created sheets using the superimposed profile. I used the wizard and had Civil 3d do it for me (2012). Now I have to add a 4th profile to the mix and get it to show in my profile views that have already been cut. The data is shortcut into the drawing with my cut profiles views. How do I get it to be in the cut profile views without re cutting everything?
Im currently using an addon for Civil 3D called Novapoint. It allows me to create 3D models of surfaces made out of 3d faces and easily models cut and fill 3d-models for me.
The only thing i need to create a cut and fill model is one or several ground surfaces (existing ground, earth layers, rock etc. whatever i need) and a closed polyline/3Dpolyline that represents the level I want my cut and/or fill model.
I enter the spcifications I want such as; earth cut angle, rock cut angle, fill angle, select which surfaces i want to include in the model calculation and select the polyline.Novapoint then calculates the cut/fill model from the surfaces to the polyline and models the different cut/fill angles and gives me the results in a 3d-face model and a specification of the volyme of rock cut, earth cut an fill.
1. Novapoint is quite unstable and crashes alot
2. You cant create profiles out of 3d faces
3. Novapoint does not automaticly combine the start surfaces with the modeled cut/fill surface
4. A large surface made out of 3d-faces demands alot of computer power
So I want to how I do the same that Novapoint does for me in Civil 3D? (I have access to Civil 3D 2007-2013 depending on which one you're using)I know I can take the 3Dfaces i created in Novapoint and make a surface in Civil 3D with them but I want to exclude Novapoint completely.
Im creating a Profile Bandset and would like to have multiple surface/profile elevations shown, ie: EG, FG, Back of Curb and Back of walk. While creating this bandset I see that the text component editor properties only has code for profile 1 elevation and profile 2 elevation in the properties area, which the code for this looks like below.
We have an engineer who is taking an existing surface and wants to show a proposed road 2" higher than existing.
I told him to simply adjust his assembly for his corridor to account for the 2" difference, but the County agency needs to see a profile.
1) Is there a way to easily copy a profile made from a surface and "convert" it to a proposed profile? If we copy and explode, it turns into hundreds (thousands?) of tiny pline segments and it would be a mess to convert all those to a profile 1 by 1. If we make the corridor, and choose "profile from corridor", we do not have an option that could be used to represent the centerline.
2) Other than loss of dynamic updating), would it make sense to adjust the assembly so the top surface would be accurate, then copy the profile, explode the copy to a block and simply shift that (as essentially basic linework)?
Attached are survey points that created the surface of a road embankment portion that caved-in. The road is very near a reservoir shoreline.
1. How can a surface profile be produce? I/'ve use line to change it into an alignement and then create a proile , then a profile view. But the the surface profile is missing.
2.the points having higher elevation are the top edge( road level) of the cave-n . A few few shots were take before the shorline elevations.
3. What the best way to come up with the rock volume to fill the cave-in given this surveying points., Also the shoreline elevation will be lowered some more while work is being done since the fill is not allowed to fall in the reservoir.
Some background: We have a composite surface of existing surveyed contours as a TIN pasted into existing aerial contours that we received from a client. We used polylines to generate our proposed contours, and then generated a proposed surface from that. We've made a blank surface, pasted in the existing surface, and are trying to paste in our proposed surface... only the existing contours outside of the proposed suface no longer line up correctly once we do.
We've tried applying the method laid out here: [URL] ........ (and the link referenced in the bottom) but are still having trouble getting the surface to work. We've tried offsetting as little as 0.25' and as much as 5' with the feature line draped over the existing surface, but it seemed that the greater the offset, the greater the discrepancy.
Just to make sure we even tried that correctly - should the breaklines that we add be standard or non-destructive? (I've tried it both ways with little success either way, so I don't know if it matters much in this instance, but perhaps for future reference it would work.)
I've attached a screen shot of our surfaces. The pink and green lines are the proposed contours, the white dashed are the existing. The outer red line is offset 0.25'. As I've mentioned, we've tried offsetting various amounts with decreasing success.
I'm currently working on a profile and I just don't understand why my profiles barely show any stations. It doesn't even show the very first station. I remember checking on a box that mentioned showing the 1st station and still nothing. I've gone into the edit band style and turned on the labels at minor stations but it just turned on the FG/EG elevations.
I've added a picture showing what i'm talking about. It only shows stations 31+00 and 32+00. Not 30+00 or the 50' increments. Also, while I'm on the subject. How do I get something proposed into this existing profile to show FG Elevations. Example if I just wanted to strike a straight line from 30+00 to the end where the elevation is a 91' & 86'.
HP Compaq 8100 Elite Win 7 Pro SP1 - 64Bit 8GB RAM i7 860 @ 2.80 GHZ AutoCad Civil 3d 2012 SP1
I have been given a survey on AutoCAD which was orginally 2D with the levels written in text next to it. I changed each point (690) to include the level in the Z-direction. I am trying to calculate volumes of topsoil removal and then cut anf fill volumes.
So I opened up Civil3D in metric template and imported my drawing as I have not been given a ddata file with the co-ordinates. Unfortunately I am having trouble creating a surface between the existing points.
I have a survey of an existing road surface and need to show where water will collect (pond). I can obviously use the water drop function and show where water will flow over the surface, but what I need to show are the resultant pond extents on the surface.
I am having some trouble creating a TIN from a point layer in Civil 3D 2011. Would the best course of action be to extract the points from the drawing and creating a surface from there, or is there a way to create the TIN around the existing points in Model space?
I'm much better versed in AutoCAD, but excited about furthering my understanding with Civil3D.
I am fairly new to the Civil side of AutoCAD, as I used to work primarily in Map. I am working on a street rehab project in which I need to take survey points showing existing elevations (centerline, flowline, and top of curb) and show existing profiles in a profile view. I have no problems setting up the profile view(s) or the centerline alignment, but I am having problems with creating the profiles themselves, and I have a two part question about them
Question 1: According to the user's guide, the correct way to set up an "existing" profile is by extracting it from a surface, but I don't have a surface to use. In reading through the various profile types, the best way to set up what I want seems to be by using the profile layout tools, but the help says that a profile layout is supposed to be for a final "proposed" profile, not the existing. Does this actually matter? Will I be breaking Civil functionality by creating an existing profile using the profile layout tools?
Question 2: In reading through the profile layout tools, everything seems to be centered around PVI's. Even using the "tangent tangent" method to add in points seems to only use the first and last point as controls, with everything in between treated as a PVI. If you look at the documentation here, points one and four are treated as actual elevations, while curvature occurs at points 2 and 3. In my case, since what I have is a series of actual points on a surface, each point should be an actual surface elevation with curvature occurring between points and not at them. What method should I be using to input the points in the profile?
I have one surface "EG" and two alignments, I'll call 1 and 2. The profile view already has the alignment 1 surface projected on it. I go to profile>Create Surface Profile and select alignment 2, Surface EG, go to ADD it but the profile list is empty. Shouldn't it already be populated with alignment 1 and all I'm doing is adding 2 to it? Both alignments are in the same site.
I don't undrstand why my assembly line increased after the existing surface in cut and fill condition, it should be stop at the existing surface. due to this problem my cut and fill quantities is not coming accurate. I'm attaching the screens shot of section. I'm using civil 3d 2009 32 bit software.
I have a rather large project for a roadway reconstruction. Therefore, the existing utilities are in a separate drawing and the existing ground surface model is in a separate drawing. All the above surface items (curb and gutter, asphalt, concrete, signs, sidewalks, landscaping, etc..) are in the master drawing. I then xref'd in my utility drawing and though I would use data shortcuts for my existing ground surface drawing. I took the surveyed triangles (3d faces) from our raw survey drawing and copied them into my surface drawing, created a surface from the triangles, created a boundary and such. So far everything is good. I created the working folder for the data shortcuts for this project and saved the drawing and closed it. I went into my master drawing and clicked on "Create Reference". I did not promote. The reference came though and everything is fine. Now I want to add contour labels in my surface drawing which I did but they do not show up in my master drawing but the contours themselves do. Do I have to promote this drawing into my master drawing so I can create the contour labels in my master drawing? I guess that is fine but the issue is we have small areas of topo that will be added as needed down the road. If I promote the surface drawing into my master drawing then when I add topo to the surface drawing, it wont update in my master drawing.
I have an existing surface with a steep slope and a feature line for the edge of a proposed walkway. I need a buffer of 25m on either side of the walkway but offsetting doesn't take the grade of the slope into account. How do I grade down the hill from the feature line at 25m to match to the existing surface?
In highway construction, I usually check for lowest ditch elevation and see how the existing drainage flows. Typically one would create or specify in CL profile creation with a 15m offset right and left which would then generate existing CL and 15m offset profiles in profile view. However, the 15m offset profile might not represent the lowest point in the ditch as the lowest elevation offset distance varies along the highway.
My question: Is there a way in civil 3D profile creation where it can automatically trace the lowest elevation in the ditch and plot it in profile view?
I have an existing ground profile, and a design profile. All I want to do is label the slopes of the design. When I click my line label style and turn on the text it labels the existing ground and the design ground. I cannot find the setting in my two profile styles to turn the slopes off in the existing ground.
Oh, how can I get a tick on the V.C. dimension line?
I am trying to create a localized existing surface from a very large topo. I promoted the existing surface shortcut into my drawing, then created a cropped surface to be put in a new drawing. After creating the cropped surface the new file shows that a surface has been created, however, the surface contains no data. I am using c3d 2012.
I have a proposed surface that has been made by selection polyline with a z elevation as contours. Is it possible to have civil 3d easily change the weeding and supplementing factors to a tighter value after it has already been made?
if i want to target the existing surface beyond the edges of my road/sidewalk, should i use the link slope to surface subassembly at both ends? i want the model to test if in a cut or fill situation, and then target.