AutoCAD Civil 3D :: Corridor And Assembly Daylight

Nov 14, 2013

I am creating a corridor with a simple assembly. On my assembly, I have basic lane and daylight Multiple surface. My target is existing ground.

View 9 Replies


AutoCAD Civil 3D :: Corridor - Forcing A Fill Daylight

Jan 7, 2014

What is the best method of forcing a fill daylight using an assembly?  Though I've played with several links, I'm not managing to get the results I desire.

View 3 Replies View Related

AutoCAD Civil 3D :: Cannot Get Corridor Surface Boundary From Daylight Points

Jun 22, 2012

Cannot get corridor surface boundary from daylight points. Is there another way so that I do not have to trace the outer limits?

View 3 Replies View Related

AutoCAD Civil 3D :: Corridor Item To Continue Past Daylight Along EG

Feb 4, 2013

I have a corridor design and the corridor daylights very close to the pavement.  I need to have rock from the EOP out beyond the daylight point to a 30' offset from the alignment.  I need it to follow the EG and show a depth of 2' throughout.

I had to draw the rock shapes manually.  But I'd like to figure out how to do it using the corridor if possible.

Please see the attached image.  Everything beyond the daylight point was traced on top of the EG and then offset 2' to get the bottom.

View 9 Replies View Related

AutoCAD Civil 3D :: Corridor Daylight Cut-Fill Feature Lines Jump Across

Sep 20, 2013

My corridor Feature Lines for Daylight Jump across in different areas (see attached PDF)

when I look at it in 3d it looks ok but the plan view the jumped lines show up.

View 4 Replies View Related

AutoCAD Civil 3D :: Corridor Section Editor Not Displaying Daylight Lines To EG Surface

Jul 13, 2012

I'm having a random issue with the daylight ties lopes not tieing to the EG surface at all stations in the Corridor Section Editor. Some stations daylight fine. In plan view the daylight lines vary left & right as expected but don't display at all in Section Editor.
Some background info:2012 Civil 3D SP1 / 64 bit / WIN7Simple corridor used1 alignmentSame fg profileSame drefd EG surface (set all targets for daylight LT/RT)Only one assembly applied to entire corridor Attached are 2 captions of the issue I'm having which each have a cut & fill occurrence as well as a caption of the entire align. & corridor. I did try deleting corridor & recreating and even recreated a simpler assembly and still have the daylight issue in same areas of corridor.

View 2 Replies View Related

AutoCAD Civil 3D :: Corridor Surface Boundary - Line Is Jumping On Daylight Fill

Jun 22, 2013

I have problem with corridor surface boundary , in curve boundary line is jumping on daylight fill , but i have created surface on wearing layer ,also when i am adding boundary there is only 3 types of adding , corridor extends , polygon and interactively , photo attached.

I am using Civil 3D 2014

View 4 Replies View Related

AutoCAD Civil 3D :: Daylight Assembly - Fill / Cut Condition

Apr 8, 2012

I like to create a daylight assembly with following criterias

Fill/cut Condition

1. Target to surface 2.5% slope

2. If the surface is not met within 19 m from centreline, then till 19 m 2.5% slope and 33% slope afterwards till it hit the surface.

Civil3D 2012

View 2 Replies View Related

AutoCAD Civil 3D :: How To Provide Multiple Daylight Subassemblies With One Assembly

Jul 24, 2013

Have a question regarding multiple daylight subassemblies, don't know if it is possible.  So I have an assembly with a trench SA in cut condition and a project to surface in fill condition, I built the corridor with this assembly and most of things look fine.  However, there is a short stretch (in cut condition) of the corridor that I would like to modify such that a trench is not provided.  I know I can create a new assembly with my desire condition, then create a new region and drop that assembly there, but I am wondering if there any other way to achieve my goal without another assembly.

View 8 Replies View Related

AutoCAD Civil 3D :: Add Different Assembly Types Along Same Corridor

Oct 17, 2012

I want to add different assemblies (some with walls or ditches) along the same corridor at given stations

Can that be done?

View 4 Replies View Related

AutoCAD Civil 3D :: Corridor - 1st Assembly Insertion At 0+00

Sep 3, 2012

1. Attached is a file , when opened show two viewports. the plan view look OK , but the ortho on the right show a corridor not near elev. Of the  the alignment and the surface is missing ( I cannot get to the object viewer to show me the model setting) .

 Am I in big trouble and had to create a surface again?

2. The end of this corridor you have  lines all over the place ,  I probably need to create a corridor surface , correct?

3. Why is the alignment so far from the corridor model?

View 1 Replies View Related

AutoCAD Civil 3D :: Sub-assembly Not Showing In Corridor?

Mar 25, 2013

I have created a corridor of an exit ramp.  Part way through the corridor, the left side slope isn't generated.

The subgrade doesn't exist.  In the Sideslope to no side slope.png image that the corridor has a side slope and ditch at 10+600.  Also in the 10+600.png image.  But at 10+610 there is no side slope.  There is OG surface out far enough, but it seems that in the 10+610.png image that there isn't enough OG surface.   Orignally there was survey data missing in this area and it was added after the fact to the OG surface.  Why doesn't the corridor recognize it, if that is the case.  I have updated and syncronized the heck out of everything, but it still doesn't seem to work.

I should point out that this is in meters (the cross sections are 10m apart) and that it is the same Assembly being used for this area.  Also all targets are consistant through this area as well.

View 2 Replies View Related

AutoCAD Civil 3D :: Corridor Assembly Not Daylighting Properly

May 8, 2012

I'm trying to successfully get through a corridor, but to no avail.  I'm certain I'm missing a step, and I'm certain that the step I'm missing is setting a surface to daylight to. 

My project:  It's a simple grassed waterway in a parabolic shape that is ran on a proposed profile grade up a draw.  As you can see in the screen shots, it should daylight to the surface on each side.  You can also see that the majority of the profile is deeper than the assembly is tall, so I should have a corridor that daylights on each side with a gradual cut up to the surface. 

I profiled the centerline with offsets.  I need the offsets to see how deep to lay the proposed centerline in regards to how deep my waterway will be.  I get a bunch of error messages when I run the coridor, and they all deal with the offsets.

View 4 Replies View Related

AutoCAD Civil 3D :: Section Views (Assembly And Corridor)

Aug 8, 2012

I am doing public works type project. A simple road widening project. I created an alignment, surface, profile view and basic road assembly (from tool palettes) and corridor.

I created a corridor and referenced it to my "profile view", "alignment" and to "basic road" assembly. When I created section views, it shows only existing grade based on the surface and the basic road assembly is not showing on my sections. I can't figure out how to do it.

View 4 Replies View Related

AutoCAD Civil 3D :: Corridor Assembly Elevation Target

Dec 20, 2013

how to create corridor, and I have a question about assembly elevation targets.

When creating a corridor, the profile is required as dependent object, which gives the elevation of the centerline of the road. Based on the definition of assembly, the elevation of the corridor at the offset targets can be determined by the profile.  My question is if the assembly elevation target specifies the elevation at the offset target too? If so, why both profile and assembly elevation target are required?

View 6 Replies View Related

AutoCAD Civil 3D :: Build Corridor Using Conditional Slope Assembly?

Mar 3, 2012

I am trying to build a corridor using a conditional slope assembly that considers the roadway and links into the lots.

The corridor is divided into 3 regions. All targeting has been assigned.

The first region appears fine. The second and third show no links beyond the roadway.

View 6 Replies View Related

AutoCAD Civil 3D :: Corridor Assembly Appears Flat In Sections

Jul 24, 2012

I have created a proposed centerline along my existing roadway, which represents along my profile. I have created an assembly for my proposed raod with a crown, and a 2% cross-fall in each direction.

But when I generate my sections, all my proposed assemblies show up in the proper location on my section views, except there is no cross-fall showing on any of them? They are all being shown in my sections as dead flat! 0%? I've been looking for a setting to change this.? I have also deleted, and recreated my corridors and regenerate my sections, only to get the same results!

View 7 Replies View Related

AutoCAD Civil 3D :: Corridor Split - Create Blank Assembly?

Mar 4, 2013

I have a corridor split and I do not need an assembly for the first part of my corridor do I create a blank assembly for that part of the design?

View 1 Replies View Related

AutoCAD Civil 3D :: Showing In Plan Points From Assembly / Corridor

Aug 13, 2013

I've been working on a proposed ditch relocation.

I made an alignment, profile, build an assembly with it's constraints (2:1 until a certain elevation and then 3:1 to the existing ground), and made a surface from that corridor.

Now i wanted to know this : How do i generate a polyline with the assembly information ?

Using : Autodesk Civil 3D 2012
OS : Windows 7 - 64 bit pro

View 1 Replies View Related

AutoCAD Civil 3D :: Assembly Overlap When Assigning Targets For Median In Corridor

Jul 9, 2012

Here's my assembly :


when I tried to assign the Median Width in my corridor to a polyline representing media width,

I got this overlap in my Section view :

how can I maintain Objects in this cause "Lanes" attached to median no matter width change ?

Intel Core i5 M 520 @ 2.40GHz
8192MB RAM
NVIDIA GeForce GT 330M 512MB Dedicated

View 1 Replies View Related

AutoCAD Civil 3D :: Quick Profile Of Corridor - How To Turn Off Assembly Points

Oct 21, 2012

I've attach a  profile of a corridor.

I don't know how to turnoff the assembly points .

I may send another inquiry after this it has to with corridor surface and boundaries.

View 1 Replies View Related

AutoCAD Civil 3D :: Super Elevations - How To Get Corridor To Follow Default Crossfall In Assembly

Dec 13, 2012

I did a user defined super for my road.  This worked well.  However when I deleted the super data.  To try something else.  The corridor shows 0% camber or crossfall.  How do I get the corridor to follow the default crossfall in the assembly again?

View 1 Replies View Related

AutoCAD Civil 3D :: Proposed Surface Not Linking To Correct Codes Of Assembly In Corridor

Nov 20, 2013

When I paste the proposed surface with the corriodor surface and I check the profile the proposed surface ties to the bottom of the kerb ignoring the footpath.Also in the same drawing file I can't seem to export it to ACAD.

View 1 Replies View Related

AutoCAD Civil 3D :: Corridor Created Using A Primary Road Full Section As Assembly

Jan 31, 2013

I am using C3D 2013, I have a corridor created using a Primary Road Full Section as my assembly, I have all the slopes and ditching set, when I go to model the corridor the ditching is not showing correctly, only small sections of the ditching are showing when I know there should be more. I have the assembly setup to build the ditching when there is less than a meter fill, but will not work.

View 3 Replies View Related

AutoCAD Civil 3D :: Targeting Offset Alignment Layout Profile With Corridor Lane Assembly

Jul 19, 2012

For some reason I cant seem to target an offset alignment layout profile with my corridor lane assembly.  I can target the existing the existing groundprofile with the same  offset alignment, but the layout profile when targetted does not change the lane in my cross sections.  I can do this with civil 3d 2010, but not 2012.  I have tried other lane sub-assemblies and it doesn't make a difference.

View 9 Replies View Related

AutoCAD Civil 3D :: Surface Corridor Is Not Triangulating Entire Corridor Boundary

Sep 14, 2012

I have created a surface from a corridor.  I set the boundary of the surface to the daylight of the corridor.  In some areas of the corridor the surface does not triangulate see attached.

View 2 Replies View Related

AutoCAD Civil 3D :: Copy Corridor Or Corridor Station Values Only?

Dec 13, 2012

Copy a corridor successfully? I'd like to try this just a little worried about the explosion of evil this may cause to my Civil 3D session.

Even all the properties of the corridor setup from one to another would be useful. I'm building one corridor and an 2nd one that matches everything except I need to replace my Assembly with one meant for stripping.

View 9 Replies View Related

AutoCAD Civil 3D :: Corridor Surface Is Not Matching Corridor Top Links

Mar 21, 2013

My corridor surface is not matching my corridor top links.  see attachments.  this is affecting my volumes!

The section-plan(surface red).png is showing the section editor and the plan view.  the red highlighted line in section is the corridor surface and as you can see in plan view the surface is incorrect and wiggly.

The pdf is all my sections with the red linework being the corridor surface.

C3D ver 2012
Win 7, 64bit

View 2 Replies View Related

AutoCAD Civil 3D :: Cannot Get Daylight Link To Show

Apr 8, 2013

I have a corridor with conditional assembly for all 200 sections. One conditions which stretches 200 feet I can not get the daylight link to show in the sections.

View 9 Replies View Related

AutoCAD Civil 3D :: Cannot Mirror Daylight Subassembly

Apr 26, 2012

Why I can't mirror the Daylight Inside ROW Subassembly? For some reason I can only place it on the right side of my assembly and in the subassembly properties there is no option to flip it to the left. In the Modify Subassembly section when it's selected the mirror option is greyed out. 

What I am trying to accomplish seems simple enough:

I have a utility easement in a drainage ditch that is 30' wide with a sewer line designed down the center, we need a very simple 10' access road on the uphill side of sewer line with 4:1 Cut/Fill slopes on either side when possible, however when the 4:1 won't catch within the easement I need it to daylight within.

At first glance the Daylight Inside ROW seems to be the appropriate subassembly for this instance but I can't get it on the left side of my road.Is there a way to set up this parameter with a different subassembly because I can get other subassemblies on the either side just fine, for example, the Cut Slope Layout Mode subaasembly works but when I build my corridor with it the slopes tie outside of the easement in several locations.

Civil 3D 2012
Windows 7 Service Pack 1
Intel Core i7-2600 CPU

View 5 Replies View Related

AutoCAD Civil 3D :: Daylight With Variable Slope

Nov 6, 2012

I wonder is it possible to have a daylight (or other function)  that can give a different slope for datum and for the top.  This would be useful for if you have different rules (e.g. because of geotech) with regard to temporary and permanent batter slopes.

View 7 Replies View Related

Copyrights 2005-15, All rights reserved