AutoCAD Civil 3D :: Showing In Plan Points From Assembly / Corridor

Aug 13, 2013

I've been working on a proposed ditch relocation.

I made an alignment, profile, build an assembly with it's constraints (2:1 until a certain elevation and then 3:1 to the existing ground), and made a surface from that corridor.

Now i wanted to know this : How do i generate a polyline with the assembly information ?

Using : Autodesk Civil 3D 2012
OS : Windows 7 - 64 bit pro

View 1 Replies


ADVERTISEMENT

AutoCAD Civil 3D :: Corridor Style-getting Points To Show In Plan View?

Dec 31, 2013

I'm not too familiar with corridor styles.  How can get points to show on my cooridor in plan view?

View 4 Replies View Related

AutoCAD Civil 3D :: Sub-assembly Not Showing In Corridor?

Mar 25, 2013

I have created a corridor of an exit ramp.  Part way through the corridor, the left side slope isn't generated.

The subgrade doesn't exist.  In the Sideslope to no side slope.png image that the corridor has a side slope and ditch at 10+600.  Also in the 10+600.png image.  But at 10+610 there is no side slope.  There is OG surface out far enough, but it seems that in the 10+610.png image that there isn't enough OG surface.   Orignally there was survey data missing in this area and it was added after the fact to the OG surface.  Why doesn't the corridor recognize it, if that is the case.  I have updated and syncronized the heck out of everything, but it still doesn't seem to work.

I should point out that this is in meters (the cross sections are 10m apart) and that it is the same Assembly being used for this area.  Also all targets are consistant through this area as well.

View 2 Replies View Related

AutoCAD Civil 3D :: Quick Profile Of Corridor - How To Turn Off Assembly Points

Oct 21, 2012

I've attach a  profile of a corridor.

I don't know how to turnoff the assembly points .

I may send another inquiry after this it has to with corridor surface and boundaries.

View 1 Replies View Related

AutoCAD Civil 3D :: Label Corridor Links In Plan View

Jan 18, 2009

Is there a way to label corridor links in plan view ?. I would like to show my pavement cross slopes from corridor in plan view.

View 5 Replies View Related

AutoCAD Civil 3D :: Projecting Linework On Design Plan To Corridor / Surface?

May 13, 2013

My company had always used LDD until we were mandated to switch, our first project in Civil 3D is in the works.  So far we have gotten through the beginning stages (alignments, profile, corridor, assemblies) but we are having a major issue with where to go from there. Right now I am trying to complete the design line work on the plan (wheelchair ramps, driveways transitions and signage) As of now I cannot get anything to line up easily with the corridor.  I have been able to snap to the corridor so I can create a line at that exact spot to be correct, but then when I offset it will not change the elevation,  I tried doing feature line and projecting the feature lines to the surface and some of it works but it becomes very buggy. My transition lines don't transition and some other lines I would expect to be at the same elevation have major grade changes. How to create the luinework at the correct elevation and with correct transisions along your corridor and surface?

View 2 Replies View Related

AutoCAD Civil 3D :: How To Make A Label In Plan With Sections Slopes From Corridor

Jan 18, 2013

I saw on you tube channel [URL].........

How to make this label where I can show the design slope in plan.

View 1 Replies View Related

AutoCAD Civil 3D :: Corridor Section Points Report

Feb 23, 2012

When creating a Corridor Section Points Report using the Toolspace>Toolbox>Reports Manager in Civil 3D 2012, the stations get listed but only a few contain point information (see attached). 

I am trying to generate stake-out data for a proposed road.  I was able to get this report to work successfully in one of the Civil 3D tutorials, so I assume that nothing is wrong with the utility.  The problem may be related to my corridor. 

View 4 Replies View Related

AutoCAD Civil 3D :: Limit Frequency On Points From Corridor

Jun 4, 2012

I am using the COGO Points from Corridor command but would like to limit the freqency of the created points to only every 50 ft (half station) or so.  Is there a command I can change to make this happen ??  

I've checked the CreatePointsFromCorridor command setting and it doesn't seem to be there...

View 2 Replies View Related

AutoCAD Civil 3D :: Corridor Section Points Report

Dec 27, 2013

I have a problem with the corridor section points report on Civil 3d 2014. It only presents the first station on the corridor.

Attached image.

View 3 Replies View Related

AutoCAD Civil 3D :: Corridor And Assembly Daylight

Nov 14, 2013

I am creating a corridor with a simple assembly. On my assembly, I have basic lane and daylight Multiple surface. My target is existing ground.

View 9 Replies View Related

AutoCAD Civil 3D :: Add Different Assembly Types Along Same Corridor

Oct 17, 2012

I want to add different assemblies (some with walls or ditches) along the same corridor at given stations

Can that be done?

View 4 Replies View Related

AutoCAD Civil 3D :: Corridor - 1st Assembly Insertion At 0+00

Sep 3, 2012

1. Attached is a file , when opened show two viewports. the plan view look OK , but the ortho on the right show a corridor not near elev. Of the  the alignment and the surface is missing ( I cannot get to the object viewer to show me the model setting) .

 Am I in big trouble and had to create a surface again?

2. The end of this corridor you have  lines all over the place ,  I probably need to create a corridor surface , correct?

3. Why is the alignment so far from the corridor model?

View 1 Replies View Related

AutoCAD Civil 3D :: Cogo Points Plan Readability

Sep 5, 2013

My delima is regarding cogo point readability. I'm used to LDD so this may be the issue. I set a cogo point but I want it to stay in the same orientation. if I use orbit or dview the cogo point data reorients (rotates) to line up horizontally. I would like the data to remain as set originally. I tried changing plan readabilty in label styles but when I drag the point it rotates to the current view orientation. Is there a way to control the rotation once dragged so it does not reorient if I change the orbit or dview?

View 9 Replies View Related

AutoCAD Civil 3D :: Cannot Get Corridor Surface Boundary From Daylight Points

Jun 22, 2012

Cannot get corridor surface boundary from daylight points. Is there another way so that I do not have to trace the outer limits?

View 3 Replies View Related

AutoCAD Civil 3D :: COGO Points Duplicating Along Crown Of Corridor

Mar 19, 2012

I have created COGO points from my corridor, there seems to be 2 sets of points ontop of each other along the crown of the road.  They are different numbers, so its not the same point twice, why it would do this?

View 4 Replies View Related

AutoCAD Civil 3D :: Change Corridor Section Points Report

May 16, 2013

I am trying to find out if there is a way to change the code for the Corridor Section Points Report. See attachment.

In page 1 of the attachment you will see the names that we prefer for the different zones in our assembly as per our Standards.

On page 2 is the default names that C3D spits out as defaults (under String Cut). 

We are running C3D 2012.

View 3 Replies View Related

AutoCAD Civil 3D :: Corridor Assembly Not Daylighting Properly

May 8, 2012

I'm trying to successfully get through a corridor, but to no avail.  I'm certain I'm missing a step, and I'm certain that the step I'm missing is setting a surface to daylight to. 

My project:  It's a simple grassed waterway in a parabolic shape that is ran on a proposed profile grade up a draw.  As you can see in the screen shots, it should daylight to the surface on each side.  You can also see that the majority of the profile is deeper than the assembly is tall, so I should have a corridor that daylights on each side with a gradual cut up to the surface. 

I profiled the centerline with offsets.  I need the offsets to see how deep to lay the proposed centerline in regards to how deep my waterway will be.  I get a bunch of error messages when I run the coridor, and they all deal with the offsets.

View 4 Replies View Related

AutoCAD Civil 3D :: Section Views (Assembly And Corridor)

Aug 8, 2012

I am doing public works type project. A simple road widening project. I created an alignment, surface, profile view and basic road assembly (from tool palettes) and corridor.

I created a corridor and referenced it to my "profile view", "alignment" and to "basic road" assembly. When I created section views, it shows only existing grade based on the surface and the basic road assembly is not showing on my sections. I can't figure out how to do it.

View 4 Replies View Related

AutoCAD Civil 3D :: Corridor Assembly Elevation Target

Dec 20, 2013

how to create corridor, and I have a question about assembly elevation targets.

When creating a corridor, the profile is required as dependent object, which gives the elevation of the centerline of the road. Based on the definition of assembly, the elevation of the corridor at the offset targets can be determined by the profile.  My question is if the assembly elevation target specifies the elevation at the offset target too? If so, why both profile and assembly elevation target are required?

View 6 Replies View Related

AutoCAD Civil 3D :: Corridor Not Fully Showing In Cross Sections?

Jul 30, 2012

I have a corridor with two baselines, one on the south side of the road, and one on the north side.  The south baseline appears correctly in the section view.  It is an asphalt bike trail with a ditch to the left side.  The north baseline was not appearing at all.  The assembly was just a ditch with nothing else.  I changed the north baseline to use the same assembly as the south to troubleshoot.  The pavement comes in, but the ditch still does not appear.

I can see the ditch feature lines on my corridor (see attached), but they are not appearing in the section view.

View 1 Replies View Related

AutoCAD Civil 3D :: Showing Corridor Assemblies In Crossing Profiles

May 11, 2012

Is there a way to show a corridor assembly in a crossing profile in c3d 2012? I have a underground duct bank that I have modeled using a  simple corridor. Now I want to have the duct bank assembly show up in another profile that crosses the ductbank corridror. I can't really create a surface fom the corridor since the duct bank a closed polygon. BTW, The subassembly for the duct bank was created from a polygon, if that is any useful info.

View 6 Replies View Related

AutoCAD Civil 3D :: Change Codes For Corridor Section Points Report?

Nov 7, 2013

I would like to have my corridor section points report to have different labels for the points like Edge of Shoulder or EOP instead of labels like P2 and Hinge.  Is the only way to do this to somehow change the codes in the stock subassemblies? 

Civil 3D 2014

View 4 Replies View Related

AutoCAD Civil 3D :: Edit Corridor Surface Manually By Editing Points

Oct 4, 2013

I was trying to edit a corridor surface manually by editing points and tin lines but for me its much easier to edit the contours itself so I explode the surface into polylines and fix the contour issues but when i make it into a new surface the Surface does not look clean anymore. When I look at it in the object viewer it looks rough and jagged and doesn't look like a road at all, however my original corridor surface did look clean with perfect roads and cul de sacs i just wanted to fix the contours outside the road. I tried extracting it like i should have done in the first place but when i add the contours to a surface it still looks ugly and jagged. Another thing is that when you look at it in 2D or plan view the contours look exactly the same but when i look at it from a perspective view or 3D that's when you see the difference.

View 3 Replies View Related

AutoCAD Civil 3D :: Build Corridor Using Conditional Slope Assembly?

Mar 3, 2012

I am trying to build a corridor using a conditional slope assembly that considers the roadway and links into the lots.

The corridor is divided into 3 regions. All targeting has been assigned.

The first region appears fine. The second and third show no links beyond the roadway.

View 6 Replies View Related

AutoCAD Civil 3D :: Corridor Assembly Appears Flat In Sections

Jul 24, 2012

I have created a proposed centerline along my existing roadway, which represents along my profile. I have created an assembly for my proposed raod with a crown, and a 2% cross-fall in each direction.

But when I generate my sections, all my proposed assemblies show up in the proper location on my section views, except there is no cross-fall showing on any of them? They are all being shown in my sections as dead flat! 0%? I've been looking for a setting to change this.? I have also deleted, and recreated my corridors and regenerate my sections, only to get the same results!

View 7 Replies View Related

AutoCAD Civil 3D :: Corridor Split - Create Blank Assembly?

Mar 4, 2013

I have a corridor split and I do not need an assembly for the first part of my corridor do I create a blank assembly for that part of the design?

View 1 Replies View Related

AutoCAD Civil 3D :: Cross Section Showing Corridor And Surface Mismatch

Mar 19, 2013

The FG was created from the corridor.

The cross sections show the EG, FG and Corridor.  Yet the Corridor is NOT ON the FG surface.

This is only happening on one section (0+20).  The other sections look good.

View 8 Replies View Related

AutoCAD Civil 3D :: SAC- Marked Points / Creating Corridor With Custom Assemblies On Two Alignments

Jan 7, 2014

I am creating a corridor with custom assemblies on two alignments. the alignments are not parallel and graded independently.

Between the two assemblies I would like to fill from one assembly to the other with a dynamic link. I can't do this as a target to featureline etc as it is within the same corridor. We have created the link with a target but this was done by creating a non-dynamic featureline from the corridor and using that as the target. This is obviously not great as far as keeping the corridor dnamic is concerned.

So I would like to customise a subassembly to allow it to target a marked point on an adjacent assembly.how the SAC tools (Get marked poinit or set marked point etc.) can be used to do this. The help file is less than useful. I am still on 2012 and dont have access to the 2014 SAC yet but will do shortly.

View 4 Replies View Related

AutoCAD Civil 3D :: Pipe Network Structure Not Showing Up In Plan View

Feb 29, 2012

I have 7 manholes in my network, only 3 of them are visibile in the model tab though.

There is structure label on all of the manholes

I can use select similar to mark them and i get "Structure (7)".

I can even see them in the object viewer.

AutoCad 2011 & Civil3D 2011. Product Version 3.
EliteBook 8560w
Intel i7 CPU 2820QM @ 2.3GHz
8 GB RAM
NVIDIA Quadro 1000M
Windows 7 Enterprise 32 Bit

View 4 Replies View Related

AutoCAD Civil 3D :: Assembly Overlap When Assigning Targets For Median In Corridor

Jul 9, 2012

Here's my assembly :

and 

when I tried to assign the Median Width in my corridor to a polyline representing media width,

I got this overlap in my Section view :

how can I maintain Objects in this cause "Lanes" attached to median no matter width change ?

Sony VPCCW26FA
Intel Core i5 M 520 @ 2.40GHz
8192MB RAM
NVIDIA GeForce GT 330M 512MB Dedicated

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved