I wonder is it possible to have a daylight (or other function) that can give a different slope for datum and for the top. This would be useful for if you have different rules (e.g. because of geotech) with regard to temporary and permanent batter slopes.
View 7 RepliesI'm modeling a simple corridor (12' lane 2%, 6' shoulder 6%, 4:1 to match EG). I used the "LinkSlopeToSurface" subassembly for the 4:1 to match the EG. Unfortunately our EG isn't always wide enough for the 4:1 slope to match it somewhere.
Is there an assembly that would use 4:1 as a standard daylight slope, but where necessary adjust the slope, max. 3.5:1, to match EG surface?
I need to daylight to an offset, to create a clear zone/fall zone, but it must have a maximum slope of 6:1. If no daylight is found at the offset and maximum slope, then grade at the maximum slope to the offset then daylight to the target suface at a steeper slope.
View 9 Replies View RelatedI have a fairly simple corridor, however, I had to modify the alignment, rebuild the corridor and resample cross-sections. Now my right daylight slope won't show up. It shows up in the section viewer, but not the cross-section. I had this problem once before and fixed it, but now I can't remember how I did...I have all targets, sections sampled match corridor sampling etc.
Civil 3D 2012 SP1
Windows 7
I am trying to create in my sub assembly a daylight with a variable slope to a graded ditch then it back slopes to natural ground. (image attached). How can I do this in Civil 3d 2012?
View 9 Replies View RelatedThis seems like something that should be really easy but for the life of me I can't figure it out. I even started looking at using the Subassembly composer to create a custom SA but that seems like a ton of work so something that would seem to be a common problem.
I need to provide a v-ditch with 2:1 side slopes at the toe of a 2:1 fill slope. The flow line of the ditch should be 2 ft below the daylight point of the roadway pavement section.
My problem is that the conditional subassembly seems to evaluate the height of fill directly beneath the attachment point of the conditional SA (pavement section daylight point in my case – “Daylight_Sub” Point code). Instead I need it to evaluate the difference in elevation between the catch point of a 2:1 daylight fill slope and the conditional SA attachment point (Daylight_sub). If that difference is less than 2 feet, I need to provide the ditch, otherwise I can just use the daylight slope for the ditch foreslope and the existing surface for the backslope.
how to do this? Maybeits as easy as using a predefined daylight subassembly that I'm overlooking?
Here’s my current assembly attempt:
And the resulting behavior. It is solving the 2nd fill condition when I would like it to solve the 1st fill condition:
I'm trying to build the ditch portion of my Subassembly backwards from an offset target "DitchOffset". The elevation of this point should be derived from a point that is using Slope and Delta Y from point "P12" (see attached). Must be at least 1m from the bottom of SubBase with a 5:1 slope.
The Ditch Bottom will be variable width. I'd like to be able to select my offset alignment for my ditch bottom. Have a link from this point extend at a slope to the Target Surface to complete the foreslope.
I can't quite picture how to complete the links from the DitchOffset point. This may be complicated but the diagram identify what I'm trying to do.
Can you not perform a slope-slope intercept to place a PVI? Essentially holding the sta and elev of the PVI's directly before and after the PVI of interest and changing the grade in and out so that the sta and elev of the PVI of interest are changed.
View 2 Replies View RelatedCan't figure out how to match gutter slope to outside lane super subassembly slope. Have super eop targeting a feature line with elevations, but when i check section editor gutter slope doesn't match pavement slope.
Civil3D 2013
Windows 7, 64 bit
Intel i7 2600 @ 3.40Ghz
16 GB RAM
Nvidia Quadro 600
i need a shoulder subassembly that varies slope in relation to the lane superelevation slope. i know that i can get a subassembly for the shoulder that will follow the alignment superelevation xml data but in my case i can't use it because we are just adding a shoulder to an existing road. we're not changing the superelevation of the existing road, just milling and overlaying and widening. right now i've created a profile of the outside edge of the shoulder that gives me the correct shoulder slope but whenever i change my centerline profile i have to redo the shoulder profiles which is a real time suck.
View 9 Replies View RelatedI am in the process of transitioning from land desktop to Civil 3D. I design roads in steep terrain and sometimes need to have my catch (daylight) slopes change. So my question is, how do I change a daylight slope at a specified depth? For example, from the shoulder of the road I want a 3:1 fill slope to a depth of 10 feet than change to a 2:1 slope until it catches the existing surface. Can this be built into a subassembly such that if the fill is less than 10 feet it will daylight correctly at a 3:1 and if the depth is greater than 10 feet then it carries the 3:1 for 10 vertical feet and then changes to the 2:1 until it daylights?
View 9 Replies View Relatedhow to create a floor or structural slab that is both sloped AND has a variable thickness?
I can do either, but not both. Thinking that I may need to create a generic mass.
I am creating a corridor with a simple assembly. On my assembly, I have basic lane and daylight Multiple surface. My target is existing ground.
View 9 Replies View RelatedI have a corridor with conditional assembly for all 200 sections. One conditions which stretches 200 feet I can not get the daylight link to show in the sections.
View 9 Replies View RelatedWhy I can't mirror the Daylight Inside ROW Subassembly? For some reason I can only place it on the right side of my assembly and in the subassembly properties there is no option to flip it to the left. In the Modify Subassembly section when it's selected the mirror option is greyed out.
What I am trying to accomplish seems simple enough:
I have a utility easement in a drainage ditch that is 30' wide with a sewer line designed down the center, we need a very simple 10' access road on the uphill side of sewer line with 4:1 Cut/Fill slopes on either side when possible, however when the 4:1 won't catch within the easement I need it to daylight within.
At first glance the Daylight Inside ROW seems to be the appropriate subassembly for this instance but I can't get it on the left side of my road.Is there a way to set up this parameter with a different subassembly because I can get other subassemblies on the either side just fine, for example, the Cut Slope Layout Mode subaasembly works but when I build my corridor with it the slopes tie outside of the easement in several locations.
Civil 3D 2012
Windows 7 Service Pack 1
Intel Core i7-2600 CPU
16GB RAM
Is it possible to make a bench right before the daylight line meets the top surface (Original Ground)?
The Road prism is a tylical shape that has a u-shaped ditch on one side. The daylight line from the outside edge of the ditch follows a series of comlicated benches at set elevations and then terminates at OG with no trouble but I'm trying to get an additional bench to be generated before OG (see attached + yellow lines).
how to add this extera bench?
I am working on a project where some of the corridors require different daylight slopes. I need to transition between a region with 2:1 slope to a 10:1 slope. My local civ3d support said something about using grading tools to achive that.
What I understood was that my assemblies should not have any daylight sub-assembly and that i should grade the corridor and than add a transition zone between the different gradings. Did I understand correctly?
I have a list of offset distance from centerline on both sildes (left and right). I want to use this to create a polyline that represents the daylight. these offsets are taken from an old hardcopy drawings of cross-sections. is there any way to draw this polyline that follows the alignment?
file can be .txt or .csv
I got this problem during creation of corridor surface boundaries. I would like to create a corridor datum surface using the daylight feature lines, automatically from the corridor surfaces-boundaries dialog box, but the daylight does not appear in the list.
View 5 Replies View RelatedWhere are the setting for the display for grading lines such as features, daylight lines, etc in the standard grading pallet?
View 1 Replies View Relatedhow to use daylight basin, for creating ditch
View 3 Replies View RelatedI have been asked to put a feature (a diversion berm) at the daylight line of a roadway where cut conditions exist off the proposed shoulder. Because of the length of the project, it would be useful if this could be done automatically as part of the corridor, rather than creating a feature line from the daylight line and grading it separately.
Is there a way to continue an assembly past the initial daylight line and make it conditional to cut situations?
What is the best method of forcing a fill daylight using an assembly? Though I've played with several links, I'm not managing to get the results I desire.
View 3 Replies View RelatedI like to create a daylight assembly with following criterias
Fill/cut Condition
1. Target to surface 2.5% slope
2. If the surface is not met within 19 m from centreline, then till 19 m 2.5% slope and 33% slope afterwards till it hit the surface.
Civil3D 2012
Original intent was for daylight to have 4:1 slope and keep within the R/W. This causes some areas to hold water as shown circled in the image. I know I should be able to give it parameters or targets to avoid this.
View 1 Replies View RelatedCannot get corridor surface boundary from daylight points. Is there another way so that I do not have to trace the outer limits?
View 3 Replies View RelatedHave a question regarding multiple daylight subassemblies, don't know if it is possible. So I have an assembly with a trench SA in cut condition and a project to surface in fill condition, I built the corridor with this assembly and most of things look fine. However, there is a short stretch (in cut condition) of the corridor that I would like to modify such that a trench is not provided. I know I can create a new assembly with my desire condition, then create a new region and drop that assembly there, but I am wondering if there any other way to achieve my goal without another assembly.
View 8 Replies View RelatedI need to rough in a drainage pipe network that connects several structures around a site. The pipe inverts need to be 6.5' below the finished floor of each unit and must maintain a minimum 2% slope. The network needs an outfall at some undetermined point on the site. The pipes must follow some existing roads, so they are not interconnected directly to each structure.
How can I go about determining the potential outfall locations?
I have a corridor design and the corridor daylights very close to the pavement. I need to have rock from the EOP out beyond the daylight point to a 30' offset from the alignment. I need it to follow the EG and show a depth of 2' throughout.
I had to draw the rock shapes manually. But I'd like to figure out how to do it using the corridor if possible.
Please see the attached image. Everything beyond the daylight point was traced on top of the EG and then offset 2' to get the bottom.
I'm building up my assembly and I want to add a daylight sub-assembly in order to grade my proposed surface to the existing surface. Typically I would have a 1:3 slope up or down. I have choosen the DaylightGeneral for this and although there is quite a few parameters to play with, I'm only interested in the up/down slope but when I put anything sleeper than 1:4 it doesn't work, I get this red line and circle.
View 4 Replies View RelatedI've created a corridor with a Cul-de-sac. The problem is that the daylight lines targeted to the existing ground intersect at turn segments:
which results in defects of corridor surface:
I wonder if there's a way to overcome this.