I have a list of offset distance from centerline on both sildes (left and right). I want to use this to create a polyline that represents the daylight. these offsets are taken from an old hardcopy drawings of cross-sections. is there any way to draw this polyline that follows the alignment?
file can be .txt or .csv
I have been asked to put a feature (a diversion berm) at the daylight line of a roadway where cut conditions exist off the proposed shoulder. Because of the length of the project, it would be useful if this could be done automatically as part of the corridor, rather than creating a feature line from the daylight line and grading it separately.
Is there a way to continue an assembly past the initial daylight line and make it conditional to cut situations?
I have problem with corridor surface boundary , in curve boundary line is jumping on daylight fill , but i have created surface on wearing layer ,also when i am adding boundary there is only 3 types of adding , corridor extends , polygon and interactively , photo attached.
I am using Civil 3D 2014
Feature lines are easy to make and great for grading. However, when I try to save the drawing into *.dxf, all the feature lines disappeared. Does this mean DXF files do not take feature lines?
I need the DXF files to up load into GPS. Do I have to redraw everything in 3D polyline?Or is there an easier way to convert feature lines into 3D polylines?
I want to create new vertex points in feature line and 3dpol.
I have this:
try
{
if (obj.GetType() == typeof(Autodesk.AutoCAD.DatabaseServices.Polyline3d)) {
Polyline3d p3d = (Polyline3d)trans.GetObject(entRes.ObjectId, OpenMode.ForWrite);
[Code]....
In this code line:
oFtrLn.InsertFeaturePoint(punt, AeccLandFeatureLinePointType.aeccLandFeatureLinePointPI);
always catches the same Exception "the value is not within the expected range" .I have translated it because I get "El valor no está dentro del intervalo esperado". Perhaps is this: " Value does not fall within the expected range.".
I have tried it with different point3d values but always catches Exception.
With pol3d I have similar problem.
Autocad Civil 3D 2014 +SP1
Quad Core Intel i7 3770-cpu 3.40Ghz.
ssd samsung 840 pro 512gb+ssd samsung 840 pro 256 gb+1tb hdd
32gb RAM 1600 Mhz.
nVidia Quadro 2000.
Win 7 Pro 64bit
I'm working on crane pads for a windfarm development and have run into an issue that has never happened in the other 60 or so ones I've done previously.
I have a polyline (elevation added in via Properties) that I want to convert to a feature line for use in grading but when I try to convert I get the message below
When I check the properties and do a LIST the list reports a negative elevation.
Im still new to Civil 3D and i would like to know how to connect inported points using 3D polylines. I imported my points from Excel in a PNEZD format. How do i get the 3d poly line to snap to my points so I can Connect them? someone mentioned using a feature line to connect the points but im not sure how or what that would do.
View 3 Replies View RelatedI have created a feture line from a 2d polyline.
I have NO weed appplied and as you can see there are two errors :
- some points on original surface (used to get Z) are not interpolated.
- the quick profile shows error : in addition to lacking points, others are bad interpolated.
(the image show both)
The surface used behaves rightly with feature lines created from aligments
(I have created an aligment from polyline and then a fetaure line from that and the Z interpolation are ok )
Civil 3D (2013)
When I label contours by "Contour Multiple", I get a line going thru my contours. I can remove this thru the Properties pallette.
Is there a setting somewhere to make it default to not draw a line?
C3d 2010 (no SP)
Win7
C3D 2012
I have a number of Sites in my drawing. I want to be able to set a Site current (in LISP) so that when you create or draw a feature line, the site is set to the desired value. I haven't seen a variable or setting for this.
I want to convert a 3D polyline to 2D polyline.
View 5 Replies View RelatedI am creating a corridor with a simple assembly. On my assembly, I have basic lane and daylight Multiple surface. My target is existing ground.
View 9 Replies View RelatedI have a corridor with conditional assembly for all 200 sections. One conditions which stretches 200 feet I can not get the daylight link to show in the sections.
View 9 Replies View RelatedWhy I can't mirror the Daylight Inside ROW Subassembly? For some reason I can only place it on the right side of my assembly and in the subassembly properties there is no option to flip it to the left. In the Modify Subassembly section when it's selected the mirror option is greyed out.
What I am trying to accomplish seems simple enough:
I have a utility easement in a drainage ditch that is 30' wide with a sewer line designed down the center, we need a very simple 10' access road on the uphill side of sewer line with 4:1 Cut/Fill slopes on either side when possible, however when the 4:1 won't catch within the easement I need it to daylight within.
At first glance the Daylight Inside ROW seems to be the appropriate subassembly for this instance but I can't get it on the left side of my road.Is there a way to set up this parameter with a different subassembly because I can get other subassemblies on the either side just fine, for example, the Cut Slope Layout Mode subaasembly works but when I build my corridor with it the slopes tie outside of the easement in several locations.
Civil 3D 2012
Windows 7 Service Pack 1
Intel Core i7-2600 CPU
16GB RAM
I wonder is it possible to have a daylight (or other function) that can give a different slope for datum and for the top. This would be useful for if you have different rules (e.g. because of geotech) with regard to temporary and permanent batter slopes.
View 7 Replies View RelatedIs it possible to make a bench right before the daylight line meets the top surface (Original Ground)?
The Road prism is a tylical shape that has a u-shaped ditch on one side. The daylight line from the outside edge of the ditch follows a series of comlicated benches at set elevations and then terminates at OG with no trouble but I'm trying to get an additional bench to be generated before OG (see attached + yellow lines).
how to add this extera bench?
I'm modeling a simple corridor (12' lane 2%, 6' shoulder 6%, 4:1 to match EG). I used the "LinkSlopeToSurface" subassembly for the 4:1 to match the EG. Unfortunately our EG isn't always wide enough for the 4:1 slope to match it somewhere.
Is there an assembly that would use 4:1 as a standard daylight slope, but where necessary adjust the slope, max. 3.5:1, to match EG surface?
I am working on a project where some of the corridors require different daylight slopes. I need to transition between a region with 2:1 slope to a 10:1 slope. My local civ3d support said something about using grading tools to achive that.
What I understood was that my assemblies should not have any daylight sub-assembly and that i should grade the corridor and than add a transition zone between the different gradings. Did I understand correctly?
1. How can you join walls and slab?
2. how can you join two floors when each is in it own Construct drawing? (in sepparate drawing i connect all floors, all building, and by doing section I don't want to see lines on connections like each floor is its own unit)
3. is it possible to draw polyline, 3dpoly on a wall and "strech" it to become an opening?
4. on drawing status bar..there is a elevaton and cut elevation. I get what cut elevation stands for, but the other? (the lower elevation)
I need to daylight to an offset, to create a clear zone/fall zone, but it must have a maximum slope of 6:1. If no daylight is found at the offset and maximum slope, then grade at the maximum slope to the offset then daylight to the target suface at a steeper slope.
View 9 Replies View RelatedI am trying to create in my sub assembly a daylight with a variable slope to a graded ditch then it back slopes to natural ground. (image attached). How can I do this in Civil 3d 2012?
View 9 Replies View RelatedI got this problem during creation of corridor surface boundaries. I would like to create a corridor datum surface using the daylight feature lines, automatically from the corridor surfaces-boundaries dialog box, but the daylight does not appear in the list.
View 5 Replies View RelatedWhere are the setting for the display for grading lines such as features, daylight lines, etc in the standard grading pallet?
View 1 Replies View Relatedhow to use daylight basin, for creating ditch
View 3 Replies View RelatedWhat is the best method of forcing a fill daylight using an assembly? Though I've played with several links, I'm not managing to get the results I desire.
View 3 Replies View RelatedI like to create a daylight assembly with following criterias
Fill/cut Condition
1. Target to surface 2.5% slope
2. If the surface is not met within 19 m from centreline, then till 19 m 2.5% slope and 33% slope afterwards till it hit the surface.
Civil3D 2012
Any way I can align a new polyline to a reference polyline (orig polyline).
The 2 polys will be generally the same length, however, the number of vertices will differ.
Also I need to mantain the same distance between the vertices on the new poly and the new and reference poly won't follow the same direction.
is there a way to draw a polyline and have autocad clip everything outside of that polyline and discard it so that i end up with a smaller drawing. only the information in that polyline, nothing outside of the polyline
View 3 Replies View Relatedi need a vlisp program to draw polyline between two blocks.
View 3 Replies View RelatedOriginal intent was for daylight to have 4:1 slope and keep within the R/W. This causes some areas to hold water as shown circled in the image. I know I should be able to give it parameters or targets to avoid this.
View 1 Replies View RelatedCannot get corridor surface boundary from daylight points. Is there another way so that I do not have to trace the outer limits?
View 3 Replies View Related