I'm working on crane pads for a windfarm development and have run into an issue that has never happened in the other 60 or so ones I've done previously.
I have a polyline (elevation added in via Properties) that I want to convert to a feature line for use in grading but when I try to convert I get the message below
When I check the properties and do a LIST the list reports a negative elevation.
Feature lines are easy to make and great for grading. However, when I try to save the drawing into *.dxf, all the feature lines disappeared. Does this mean DXF files do not take feature lines?
I need the DXF files to up load into GPS. Do I have to redraw everything in 3D polyline?Or is there an easier way to convert feature lines into 3D polylines?
"An infill grading has no criteria applied to it. Any area bounded by feature lines or lot lines that is not already a grading can be converted to an infill grading."
So given an area enclosed by a feature line, an infill grading can be created. Using the same features line, an feature line grading can also be created. what is the difference between these two surfaces? They both have no criteria applied to them.
I have an existing surface with a steep slope and a feature line for the edge of a proposed walkway. I need a buffer of 25m on either side of the walkway but offsetting doesn't take the grade of the slope into account. How do I grade down the hill from the feature line at 25m to match to the existing surface?
View 3 Replies View Relatedwhy I would get gaps in my grading from a single feature line? The feature line is at the same elevation all the way around and I am trying to grade to my existing surface at a 1:1 slope. No matter what I do it continues to leave out portions of the grading. I have attached a 3d image showing what's going on.
View 1 Replies View RelatedI have grading style set up to create a cut/fill boundary and the same thing for my corridor. I made surfaces from my grading and corridor and no longer need them. I need to keep the cut/fill lines for my design. How can I extract these lines from these objects? I tried keeping the grading/corridor on one layer and lines I wish to use on another so I can turn pieces of the grading off. However, it will not print the cut/fill boundary without printing all the feature lines created from a grading.
View 1 Replies View RelatedWhen we apply surface projection gradings to feature lines, we get locked vertices on the feature line wherever the grading transitions from cut to fill. In turn these vertices create segments in the feature line which influence any labels applied to the line. I don't want a bazillion segment labels on my FL. I only want segment labels between the physical vertices and elevation points. Is there a workaround or is an enhancement request in order?
View 9 Replies View RelatedIs there away to link a i.e. (a stoop to a finish flood elev)? So that, if I were to raise the finish floor, the stoop would move also. I understand I could possible to a create grading feature line for a stoop, but what happens if the stoop would be irregular shapped and not a rectangle?
View 5 Replies View RelatedI have created a feture line from a 2d polyline.
I have NO weed appplied and as you can see there are two errors :
- some points on original surface (used to get Z) are not interpolated.
- the quick profile shows error : in addition to lacking points, others are bad interpolated.
(the image show both)
The surface used behaves rightly with feature lines created from aligments
(I have created an aligment from polyline and then a fetaure line from that and the Z interpolation are ok )
Civil 3D (2013)
I HAVE A 2D PROFILE (DWG FILE NOT CIVIL3D FILE) of a pipeline that shows invert of the pipe.
I want to have this pipe as feature line .
is there any way to convert this profile to feature line?
Is there a way to convert a feature line elevation point to PI?
My objective here is to delete all the elevation points except one. It would be time consuming to pick each elevation point and delete them individually (in this case there are about 15 but sometimes there are more). I want to use the delete all option but keep one one of them. If I can convert that one into a PI I could then quickly delete the remaining elevation points.
I have a 2D (dwg) plan and profile of pipeline ( Scanned) and I am going to find a way to have this pipe as 3d ( or featureline).
I can't do this manually because this is a long pipe.
I have a client who uses Bently MX Roads for road design and requires that survey data be supplied in GENIO format. I realise that there are many possible options to get Civil3D survey data into MX, but I am trying to explore the use of the Subscription Extension to Import/Export GENIO.
Surfaces - no problem. Points - I see how I can get that to work. But the only linework that can be exported is Feature Lines, and it is also important that the feature lines have a name (likely related to the layer it is on).
I can convert survey figures to feature lines and name them one by one but would be very time consuming for a whole survey. Is there any way of doing all figures at once?
I'm guessing not and that it is probably easier to do the Genio creation from dwg in MX itself.
Civil3D 2014 - Windows7 64bit
I have a created a surface from contour lines.I have drawn a feature line and assigned elevations (it slopes down from 3.5m elevation to 2m elevation). I have added grading from the feature line to the existing surface but have not merged the feature line with the surface.
I also have to make a low area (elevation at 1.5m) on the surface and know i need to grade at 1:1 from the feature line to the low point. Is there a way to grade from a feature line at a given grade (1:1) to a known height (my low point at 1.5m) without drawing another feature line for my low point? Seeing as the height of the feature line varies I can't just offset it at the grade.. I.e. the grade is the constant here.
I will have a few walls and lower / higher areas to grade to. I have drawn the top of my wall and mounds and have assigned them elevations but not sure whether to now make them all feature lines and try to merge with the surface by grading at a set grade or to do some sort of infill.
I am working on a complex industrial site. And I would like a constant grade of 3.00% from my road intersections to the edge of curves. I know if I used a corridor, I'd be able to tell the grading to project ot the edge of the road/curve.
I'm just wondering if I can tell a grading object to project to a polyline or feature line along a intersection curve? There are many reasons as to why I'm not using corridors for this project, but I don't want to get into that.
I have this problem when creating grading groups with more than one feature line in them. It seems really unstable when you trying get the grading to connect. I have tried to create two separate grading groups in one site or two feature lines in one grading group. And the result is the same, the grading that will be create can sometimes look oki, but suddenly they tend to disappear or look weird...
View 4 Replies View RelatedI want to convert a 3D polyline to 2D polyline.
View 5 Replies View RelatedI have feature line with elevations that represents bottom of ditch and want to go UP 3:1 slope. also i have edge of road feature line that is higher than ditch and want to go 2% down until it hits side of the ditch that is 3:1. Any easiest way in civil 3d to create intersection line between ditch bottom going up 3:1 and edge of road going down 2%?
View 2 Replies View RelatedWhen creating Feature Lines, I wanted them to be e.g. Step Line 1, Step Line 2, Step Line 3 etc so I amended the name template to suit. I created multiple from objects and the naming convention worked. If I did features individually (as I wanted certain ones in certain sites) it worked for the first feature but reverted back to the default Feature line name on subsequent entry to the dialog i.e. it had "forgotten" the template name just set.
Am I missing something to get this to work correctly or is this how it's supposed to work i.e. useless for individual feature line creation?? This also happens for gradings.
IDSP Premium 2014 (mainly Civil 3D 2014 UKIE SP1 & Infraworks with some limited 3ds Max Design)
Win 7 Pro x64, 256Gb SSD, 300Gb 15,000 rpm HDD
16Gb Ram Intel Xeon CPU E5-1607 0 @ 3.00GHz (4 CPUs), ~3.0GHz
NVIDIA Quadro 4000, Dual 27" Monitor, Dell T3600
I want to convert a line (Autodesk.AutoCAD.DatabaseServices.Line) to a polyline (Autodesk.AutoCAD.DatabaseServices.Polyline).
Currently I get all the properties from the line, create a new polyline with it and delete the line. I fear data may get lost this way. What is the best way to convert a line to a polyline?
// Line properties:// Color.// Layer.// Linetype.// Linetype scale.// Plot style.// Lineweight.// Hyperlink.// Thickness.// Material.// Start X.// Start Y.// Start Z.// End X.// End Y.// End Z.// Start point.// End point.
how a drawing was exported from another program. My problem is: the PEDIT command won't give me the option to convert a line "I" add to a pline.
PEDITACCEPT: 0 or 1, problem remains
It is a drawing from an house designer, I am adding structural members and notes over the drawing. I could xref, but I need to move/erase some of their notes as well. It becomes cumbersome to switch to the source dwg, edit & save, move to current dwg and refresh, to have the note where needed.
This is a pretty strange to me drawing file. It seems that a bunch of system variables are altered and hopefully it doesn't migrate over to files originating from my machine.
I have a few custom linetypes created for the cut and fill daylight boundary on a grading and corridor. I have it set up to put these lines on different layers than the rest of the grading. I can turn the rest of the grading off and just have my surface created from the grading and these daylight lines on that are linked to the grading. Everything looks good when I go to paperspace to print, except when I actually print the daylight lines do not. They appear in paperspace but not on an actual hard copy. I do not need the grading, I have tried extracting the lines and deleting the grading. This presents another problem. When I extract the lines the come in as a solid line and I cannot get my custom linetype to show despite changing LT scale, etc. How can I make these lines appear in the fashion I want them to.
View 2 Replies View RelatedI needed to remove a feature line that I used as a break line when creating a surface. When I removed the feature line from the definition of the surface, the grading did not change. It appears the points created by the feature line remain which is why grading didn't change. The only work around was to delete these points.
I noticed the same thing happens when I removed the surface boundary and inserted a new boundary. why these points remain and how to remove when I delete boundary and feature line from surface?
How to convert a 3D Polyline contour to Polyline contour.
View 4 Replies View RelatedHow to convert polyline into alignment?
View 1 Replies View Relatedhow to convert polyline object (with x, y, z) to TIN SURFACE BECAUSE IF THIS OBJECT STILL POLYLINE OBJECT, I CAN'T RUNNING CATCHMENT AREA, ADD LABEL ETC
View 5 Replies View RelatedI need to convert my surface boundary to a polyline so I can use it to clip another surface. Is there a simpler way than tracing it with the polyline command?
View 3 Replies View Related[URL]....
That code is also useful for feature lines or parcels?
Can I get polyline Id after we can create automatically?
I want calculate all location crossing between feature lines.
Currently, I know to do that for crossing polylines.
Autocad Civil 3D 2014 +SP1
Quad Core Intel i7 3770-cpu 3.40Ghz.
ssd samsung 840 pro 512gb+ssd samsung 840 pro 256 gb+1tb hdd
32gb RAM 1600 Mhz.
nVidia Quadro 2000.
Win 7 Pro 64bit
I have a list of offset distance from centerline on both sildes (left and right). I want to use this to create a polyline that represents the daylight. these offsets are taken from an old hardcopy drawings of cross-sections. is there any way to draw this polyline that follows the alignment?
file can be .txt or .csv
Is there any way to project feature lines into a profile when the plan view is xref'd? I have my plan view "existing topo" with all existing features/Figures and a existing surface.
My profile is a separate dwg with plan view xref'd and surface a data shortcut. Of course there are feature lines and Survey Figures in the existing top I want to project into the profile, but can't because it is an xref. Besides copying .
C3D 2012. I am trying to get the distance from the start of a featrue line to a selected point. My object is "FLobj" and my Point is PT1. I am using the method Get2dDistanceAtPoint. This is the line of code.
(vlax-invoke-method FLObj 'Get2DDistanceAtPoint pt1 'pDistance)
I keep getting "too many actual parameters".