why I would get gaps in my grading from a single feature line? The feature line is at the same elevation all the way around and I am trying to grade to my existing surface at a 1:1 slope. No matter what I do it continues to leave out portions of the grading. I have attached a 3d image showing what's going on.
View 1 Replies"An infill grading has no criteria applied to it. Any area bounded by feature lines or lot lines that is not already a grading can be converted to an infill grading."
So given an area enclosed by a feature line, an infill grading can be created. Using the same features line, an feature line grading can also be created. what is the difference between these two surfaces? They both have no criteria applied to them.
I have an existing surface with a steep slope and a feature line for the edge of a proposed walkway. I need a buffer of 25m on either side of the walkway but offsetting doesn't take the grade of the slope into account. How do I grade down the hill from the feature line at 25m to match to the existing surface?
View 3 Replies View RelatedI have grading style set up to create a cut/fill boundary and the same thing for my corridor. I made surfaces from my grading and corridor and no longer need them. I need to keep the cut/fill lines for my design. How can I extract these lines from these objects? I tried keeping the grading/corridor on one layer and lines I wish to use on another so I can turn pieces of the grading off. However, it will not print the cut/fill boundary without printing all the feature lines created from a grading.
View 1 Replies View RelatedI'm working on crane pads for a windfarm development and have run into an issue that has never happened in the other 60 or so ones I've done previously.
I have a polyline (elevation added in via Properties) that I want to convert to a feature line for use in grading but when I try to convert I get the message below
When I check the properties and do a LIST the list reports a negative elevation.
When we apply surface projection gradings to feature lines, we get locked vertices on the feature line wherever the grading transitions from cut to fill. In turn these vertices create segments in the feature line which influence any labels applied to the line. I don't want a bazillion segment labels on my FL. I only want segment labels between the physical vertices and elevation points. Is there a workaround or is an enhancement request in order?
View 9 Replies View RelatedIs there away to link a i.e. (a stoop to a finish flood elev)? So that, if I were to raise the finish floor, the stoop would move also. I understand I could possible to a create grading feature line for a stoop, but what happens if the stoop would be irregular shapped and not a rectangle?
View 5 Replies View RelatedI am trying to create a surface using the grading tool. I have a known top and a designed floor. I extended the floor surface out to meet the top breakline. I then use the grading tool to run a 3:1 down to the pond floor so I know where the true breakline is, but there is almost always a gap or two in my surface. It is usually less than a foot, but it has made my OCD kick in and I am going crazy trying to figure it out. I've traced of the breaklines, and the contours and added them to the surface to try and fix it, but that doesn't seem to work.
AutoCAD Civil 3D 2012 SP4
Windows 7 (64)
I have a created a surface from contour lines.I have drawn a feature line and assigned elevations (it slopes down from 3.5m elevation to 2m elevation). I have added grading from the feature line to the existing surface but have not merged the feature line with the surface.
I also have to make a low area (elevation at 1.5m) on the surface and know i need to grade at 1:1 from the feature line to the low point. Is there a way to grade from a feature line at a given grade (1:1) to a known height (my low point at 1.5m) without drawing another feature line for my low point? Seeing as the height of the feature line varies I can't just offset it at the grade.. I.e. the grade is the constant here.
I will have a few walls and lower / higher areas to grade to. I have drawn the top of my wall and mounds and have assigned them elevations but not sure whether to now make them all feature lines and try to merge with the surface by grading at a set grade or to do some sort of infill.
I have this problem when creating grading groups with more than one feature line in them. It seems really unstable when you trying get the grading to connect. I have tried to create two separate grading groups in one site or two feature lines in one grading group. And the result is the same, the grading that will be create can sometimes look oki, but suddenly they tend to disappear or look weird...
View 4 Replies View RelatedI have feature line with elevations that represents bottom of ditch and want to go UP 3:1 slope. also i have edge of road feature line that is higher than ditch and want to go 2% down until it hits side of the ditch that is 3:1. Any easiest way in civil 3d to create intersection line between ditch bottom going up 3:1 and edge of road going down 2%?
View 2 Replies View RelatedWhen creating Feature Lines, I wanted them to be e.g. Step Line 1, Step Line 2, Step Line 3 etc so I amended the name template to suit. I created multiple from objects and the naming convention worked. If I did features individually (as I wanted certain ones in certain sites) it worked for the first feature but reverted back to the default Feature line name on subsequent entry to the dialog i.e. it had "forgotten" the template name just set.
Am I missing something to get this to work correctly or is this how it's supposed to work i.e. useless for individual feature line creation?? This also happens for gradings.
IDSP Premium 2014 (mainly Civil 3D 2014 UKIE SP1 & Infraworks with some limited 3ds Max Design)
Win 7 Pro x64, 256Gb SSD, 300Gb 15,000 rpm HDD
16Gb Ram Intel Xeon CPU E5-1607 0 @ 3.00GHz (4 CPUs), ~3.0GHz
NVIDIA Quadro 4000, Dual 27" Monitor, Dell T3600
I have a few custom linetypes created for the cut and fill daylight boundary on a grading and corridor. I have it set up to put these lines on different layers than the rest of the grading. I can turn the rest of the grading off and just have my surface created from the grading and these daylight lines on that are linked to the grading. Everything looks good when I go to paperspace to print, except when I actually print the daylight lines do not. They appear in paperspace but not on an actual hard copy. I do not need the grading, I have tried extracting the lines and deleting the grading. This presents another problem. When I extract the lines the come in as a solid line and I cannot get my custom linetype to show despite changing LT scale, etc. How can I make these lines appear in the fashion I want them to.
View 2 Replies View RelatedI needed to remove a feature line that I used as a break line when creating a surface. When I removed the feature line from the definition of the surface, the grading did not change. It appears the points created by the feature line remain which is why grading didn't change. The only work around was to delete these points.
I noticed the same thing happens when I removed the surface boundary and inserted a new boundary. why these points remain and how to remove when I delete boundary and feature line from surface?
Is there any way to project feature lines into a profile when the plan view is xref'd? I have my plan view "existing topo" with all existing features/Figures and a existing surface.
My profile is a separate dwg with plan view xref'd and surface a data shortcut. Of course there are feature lines and Survey Figures in the existing top I want to project into the profile, but can't because it is an xref. Besides copying .
C3D 2012. I am trying to get the distance from the start of a featrue line to a selected point. My object is "FLobj" and my Point is PT1. I am using the method Get2dDistanceAtPoint. This is the line of code.
(vlax-invoke-method FLObj 'Get2DDistanceAtPoint pt1 'pDistance)
I keep getting "too many actual parameters".
I am wanting to add the name of my feature line to a label style. I am trying to create a label style that will show Lot Number and Area. I know i can create parcels, but i dont want to! I have also created a map table that can do exactly what i want on polylines, but will not work on an xref. Labelling featurelines does work in xrefs.
how to add the name into a label style?
Is there a way to decurve feature lines like how we do it with polylines? I am labeling my feature lines but don't want the curve labels to show up
View 6 Replies View RelatedI am building a surface and have back of curb, curb face, and curb flowline going around a curve. I cannot create the lines with the usual pline as they will cross due to poor field collect. I created the curbs with multiple arcs. I was then going to change them into Feature Lines and am wondering if I can then use them as breaklines in a surface.
View 1 Replies View RelatedI have a roadway alignment with FG profile and I want to place a feature line on the roadway centerline that represents the FG profile elevations.
View 7 Replies View RelatedWe have cooridors with features such as terrace drains and flowlines, but we cant seem to get the linetypes to show up correctly. For example a flow line should have arrows but it shows up without the linetype and looks continuous.
LTSCALE =1
MSLTSCALE=1
PSTSCALE=1
DRAWING SETTINGS - 1"=40'
CIVIL 3D 2012
I am building a corridor with the right side of the pavement fitting to the existing surface.The subassembly used to link the edge of pavement to the existing ground is LinkSlopeToSurface.
On the corridor created, the feature line (code P2) of the corridor surface (top) starts from the station 0+025, instead of 0+000.
I was wondering why there is no feature line P2 for station range 0+000 to 0+025? Does that mean the linkage to the existing ground surface not exist for the slope defined in the subassembly?
We are running Civil3d 2012. When converting a line or 3d poly to feature line, or just creating one it adds elevation points where it crosses surface breaklines even if you do not assign elevations. We want the feature to just have 2 elevations. The beginning and end. Is this a bug? Or is there another setting somewhere?
View 7 Replies View RelatedI created a label for retaining wall that takes the z value from the start and end of a feature line. Works great except that it isn't dynamic. I have created the feature line in a grading sheet where the surface is data shortcut into it and I'm just using grips to make sure the ends are on the bottom and top of the retaining wall. Is there any way to dynamically pin/tie the feature line to a surface that has been data shortcut?
View 9 Replies View RelatedAutoCAD C3D 2012 has been crashing nonstop over the past 3 days on me whenever I try to "Create a Feature Line from Object". I know that it is a localized problem as a co-worker has been in the same drawing and done grading work without any problems. The error has occurred in multiple drawings.
Product Version: F.107.0.0. AutoCAD Civil 3D 2012 SP1
is there a way to draw a line in the profile view and create that line into a feature line? and if there is can i project that line into the plan? i know that you can make a feature line in the plan and project that feature line into a profile view, just wondering if you could basicly do the reverse. i don't want to make a coridor.
View 4 Replies View RelatedI Created a Feature Line from Objects (a polyline). I added it to Site 1, gave it a name, layer. Do I Assign elevations during creation (conversion options)?
I set the Elevation to 8.5 (NOT From surface)
Then I go to
Modify Feature Line -
Elevation Editor.
Why are the elevations locked? I want to set them.
Why do they do this? I am trying to quick elevation edit a featureline but my edit glyph jumps to a completly different featureline that is near.
View 3 Replies View Relatedwhy this particular FL has this type of a display?
View 1 Replies View RelatedI often use feature lines for parking lots and ponds. They're great when they work, but they drive me NUTS when they don't - which is a lot of the time. For parking lots and ponds, my feature lines usually close back on themselves. That's when I have trouble breaking the feature line. When I use BREAKFEATURE, I choose two points and this should, in theory, leave a gap in the feature line between those two points. That's not what happens. I end up with a huge gap between the first point I picked and a vertex point 5 or 6 vertices away. It doesn't matter where I pick the breaking points.
I've also tried TRIMFEATURES. I draw lines across the feature line where I would have chosen the breaking points. But the portion that I want to remove is the portion that always remains. It doesn't matter where I select the feature line to be trimmed (inside or outside of the cutting edges).
I think there may something wrong with the feature line itself. Sometimes, if I erase the original and draw a new one, it will trim just fine. But that's such a headache, and it doesn't always work. If I knew what was causing the feature lines to go squirrely, I would aviod it. Unfortunately, it seems like breathing the wrong way can screw up a feature line.
I was wondering if there is a way that I can take an existing grade surface and apply a designed pond surface.
Right now I have the pond as a set of 3d Polylines in the proper geometry.
I want to place the pond into this surface and cut/fill at a 3:1 from that pond to the existing surface.