Is there away to link a i.e. (a stoop to a finish flood elev)? So that, if I were to raise the finish floor, the stoop would move also. I understand I could possible to a create grading feature line for a stoop, but what happens if the stoop would be irregular shapped and not a rectangle?
View 5 RepliesWhen we apply surface projection gradings to feature lines, we get locked vertices on the feature line wherever the grading transitions from cut to fill. In turn these vertices create segments in the feature line which influence any labels applied to the line. I don't want a bazillion segment labels on my FL. I only want segment labels between the physical vertices and elevation points. Is there a workaround or is an enhancement request in order?
View 9 Replies View Related"An infill grading has no criteria applied to it. Any area bounded by feature lines or lot lines that is not already a grading can be converted to an infill grading."
So given an area enclosed by a feature line, an infill grading can be created. Using the same features line, an feature line grading can also be created. what is the difference between these two surfaces? They both have no criteria applied to them.
I have been creating grading objects from my curb lines, assigning grades using the editor, then offsetting that line for the BACK of curb, and using the raise-lower command to raise the curb line height. If I edit the original face of curb line (gutter grade) then I go back and redo the process. Is there any way to intelligently link these two lines so that if one gets edited C3D knows the other is 0.5 feet higher (or lower) than its neighbor?
View 9 Replies View RelatedI have an existing surface with a steep slope and a feature line for the edge of a proposed walkway. I need a buffer of 25m on either side of the walkway but offsetting doesn't take the grade of the slope into account. How do I grade down the hill from the feature line at 25m to match to the existing surface?
View 3 Replies View Relatedwhy I would get gaps in my grading from a single feature line? The feature line is at the same elevation all the way around and I am trying to grade to my existing surface at a 1:1 slope. No matter what I do it continues to leave out portions of the grading. I have attached a 3d image showing what's going on.
View 1 Replies View RelatedI have grading style set up to create a cut/fill boundary and the same thing for my corridor. I made surfaces from my grading and corridor and no longer need them. I need to keep the cut/fill lines for my design. How can I extract these lines from these objects? I tried keeping the grading/corridor on one layer and lines I wish to use on another so I can turn pieces of the grading off. However, it will not print the cut/fill boundary without printing all the feature lines created from a grading.
View 1 Replies View RelatedI'm working on crane pads for a windfarm development and have run into an issue that has never happened in the other 60 or so ones I've done previously.
I have a polyline (elevation added in via Properties) that I want to convert to a feature line for use in grading but when I try to convert I get the message below
When I check the properties and do a LIST the list reports a negative elevation.
When creating Feature Lines, I wanted them to be e.g. Step Line 1, Step Line 2, Step Line 3 etc so I amended the name template to suit. I created multiple from objects and the naming convention worked. If I did features individually (as I wanted certain ones in certain sites) it worked for the first feature but reverted back to the default Feature line name on subsequent entry to the dialog i.e. it had "forgotten" the template name just set.
Am I missing something to get this to work correctly or is this how it's supposed to work i.e. useless for individual feature line creation?? This also happens for gradings.
IDSP Premium 2014 (mainly Civil 3D 2014 UKIE SP1 & Infraworks with some limited 3ds Max Design)
Win 7 Pro x64, 256Gb SSD, 300Gb 15,000 rpm HDD
16Gb Ram Intel Xeon CPU E5-1607 0 @ 3.00GHz (4 CPUs), ~3.0GHz
NVIDIA Quadro 4000, Dual 27" Monitor, Dell T3600
I have feature line with elevations that represents bottom of ditch and want to go UP 3:1 slope. also i have edge of road feature line that is higher than ditch and want to go 2% down until it hits side of the ditch that is 3:1. Any easiest way in civil 3d to create intersection line between ditch bottom going up 3:1 and edge of road going down 2%?
View 2 Replies View RelatedI want to create a line style for feature objects (line object) wich symbols only on the vertex of the line. How can I do it?
View 9 Replies View Relatedis there a way to draw a line in the profile view and create that line into a feature line? and if there is can i project that line into the plan? i know that you can make a feature line in the plan and project that feature line into a profile view, just wondering if you could basicly do the reverse. i don't want to make a coridor.
View 4 Replies View RelatedI use the create feature lines from object command from the Survey pull-down menu and choose a "Associate figure survey point to vertices" I get a survey figure that uses point elevations at some vertices and 0 at others. However, if I use Create Feature Lines from Objects under the Grading pull-down, and use a surface made of just the points, I get a a figure with all the correct elevations.
I checked the vertices where the survey figure drops to 0 and the line is snapped to the point, distance = 0.0000. What gives?
I want to create a profile layout by feature line. Is it possible?I have a pipe about 3 miles long, an alignment along the pipe, and a provie view showing the exisitng surface and pipe network. The pipe network was created from a feature line. I projected the feature line to the profile.
This is why I want to do this: I need to label the horizontal and vertical angle points of the pipe in plan view. I crated a style that shows the station and elevation. I want the elevation to reference the profile. But it only gives me the elevation of the surface and I need the top of pipe elevation.
I tried crate profile by layout and traced over the top of the pipe in profile but its 3 miles and it will take a long time. How to get what I want done faster?
C3D 2013, Win 7, 64 bit
When I try to create a feature line using an alignment/ profile, sometimes it gives me a feature line for the entire alignment, even though my profile is only a small segment. I made sure I selected the correct profile, and I even deleted all other surface profiles just in case. But it still gives me a wonky feature line for the entire alignment.
However, in the same file, other profiles have worked perfectly.
I have a created a surface from contour lines.I have drawn a feature line and assigned elevations (it slopes down from 3.5m elevation to 2m elevation). I have added grading from the feature line to the existing surface but have not merged the feature line with the surface.
I also have to make a low area (elevation at 1.5m) on the surface and know i need to grade at 1:1 from the feature line to the low point. Is there a way to grade from a feature line at a given grade (1:1) to a known height (my low point at 1.5m) without drawing another feature line for my low point? Seeing as the height of the feature line varies I can't just offset it at the grade.. I.e. the grade is the constant here.
I will have a few walls and lower / higher areas to grade to. I have drawn the top of my wall and mounds and have assigned them elevations but not sure whether to now make them all feature lines and try to merge with the surface by grading at a set grade or to do some sort of infill.
C3D 2012
I have a number of Sites in my drawing. I want to be able to set a Site current (in LISP) so that when you create or draw a feature line, the site is set to the desired value. I haven't seen a variable or setting for this.
I think this issue started with SP2. I don't remember having these issues in SP1 and earlier.
Create some COGO points at varying elevations.Start a new feature line.Use "node" object snap and pick your first cogo pointIt does not pick up the elevation of the point (it used to)Now draw feature line segments to a few more cogo points entering the elevation each time.It does not pick up the elevation of the point (it used to)Now switch to Arc mode and snap to a few more cogo points.It does correctly picks up the elevation of the cogo points (like it used to)R.K. McSwain | CADpanacea | twitter | Cadalyst tips/code
Is there a way to add elevation labels at any position on a feature line without having to create a surface?
View 9 Replies View RelatedI have this problem when creating grading groups with more than one feature line in them. It seems really unstable when you trying get the grading to connect. I have tried to create two separate grading groups in one site or two feature lines in one grading group. And the result is the same, the grading that will be create can sometimes look oki, but suddenly they tend to disappear or look weird...
View 4 Replies View RelatedIs there a way to link feature lines to points? If I have a series of points and I've joined them with a feature line; I want the feature line to update automatically if I adjust a point elevation.
View 4 Replies View RelatedI have a compost pad and retention pond to design, I set my back Pad line to surface and then graded to elevation so the slope to the pond will have no cuts
I created a pond and left out the grading to surface on the up hill side towards the pad which will be paved one day. I now created two side feature lines to enclose the whole pad and graded by distance and slope.
My problem now is the two side and back seem to blend together as I attached the feature lines together but I can not figure out how to blend into the pond create as it has side slopes to EG and the front which must join to the side slope crest to enclose the pad to drain into the pond.
It has been too long since I created Grading Objects and Proposed Surfaces. I am working in a file with my existing surface DATA Linked. I am creating a grading plan. I have created three separate grading objects in the Site named Proposed. One in the building, One is a new ditch, one is a graded existing ditch. I need to make these three with the unaffected areas of the existing surface into a new surface. How do I accomplish that . All my grading objects appear to be individually accurate and are created with a Feature Line and Grade to Surface Styles.
View 1 Replies View RelatedUsing 2010 with update 1 or whatever it's called these days, I'll just call it the first fix.
I've made three grading objects using "Grade to Relative Elevation" along a feature line. Then I've added a grading transition between them. This seems really unstable now, like making the wrong move makes the whole thing disappear...but what is strange is the feature line that is attached to the grading object that I have added into my surface remains, but there are only a few lines where the grading objects used to be, basically the line that seperates the different sections of grading.
There's no way to edit the grading again either, it has to be remade, because there is nothing to select.
Civil 3D 2010
Dell Precision 690
Intel Xeon 2.00GHz Dual Core
4 GB RAM, 256mb nVidia Quadro FX 550
Windows 7 URC 64-bit Operating System
I have grading objects that are to match existing grade. However, When I grade to match surface, I get missing countour data.....
View 1 Replies View RelatedI have a few custom linetypes created for the cut and fill daylight boundary on a grading and corridor. I have it set up to put these lines on different layers than the rest of the grading. I can turn the rest of the grading off and just have my surface created from the grading and these daylight lines on that are linked to the grading. Everything looks good when I go to paperspace to print, except when I actually print the daylight lines do not. They appear in paperspace but not on an actual hard copy. I do not need the grading, I have tried extracting the lines and deleting the grading. This presents another problem. When I extract the lines the come in as a solid line and I cannot get my custom linetype to show despite changing LT scale, etc. How can I make these lines appear in the fashion I want them to.
View 2 Replies View RelatedI have a Proposed Building Pad. Grading is 3:1 on 3 sides. Grading is 5:1 in the front of the building. How do I get Grading to fill in the area at the building corner between the 3:1 and the 5:1 grading? I thought infill would accomplish this but it seems to have no effect when I select the objects. I included a screen shot and the area at the left corner of the building.
View 4 Replies View RelatedSee how linking is happening between points along the same survey line? How to prevent this?
View 4 Replies View RelatedI have two separate graded levees in my drawing. One has created a surface just fine, the other absolutely refuses to generate a surface. I've deleted the grading even the feature lines and re-did them. In my grading group I have automatic surface creation checked and the volume base surface checked. I show the surface in the prospector but there is nothing there. The one levee will show contour styles but this one ZIP!
View 2 Replies View RelatedI have an Existing Surface i created from survey data. I have a Proposed Surface i created with feature lines. Now i want to create grading around the outside portions of my Proposed Surface. I create the Grading Group and specified a projection surface and selected a Criteria Set for a 3:1 slope to match back to Existing Surface. I select the Feature Line i wish to create the grading from and progress through the cut and fill prompts and nothing happens. Nothing gets created. I have tried an audit on the drawing to see if errors are causing the problem and there are no errors.
I use this tool all the time and this problem comes up frequently. Especially if i have made any surface adjustments.
I needed to remove a feature line that I used as a break line when creating a surface. When I removed the feature line from the definition of the surface, the grading did not change. It appears the points created by the feature line remain which is why grading didn't change. The only work around was to delete these points.
I noticed the same thing happens when I removed the surface boundary and inserted a new boundary. why these points remain and how to remove when I delete boundary and feature line from surface?