AutoCAD Architecture :: Possible To Draw Polyline / 3D Poly On A Wall
Mar 21, 2013
1. How can you join walls and slab?
2. how can you join two floors when each is in it own Construct drawing? (in sepparate drawing i connect all floors, all building, and by doing section I don't want to see lines on connections like each floor is its own unit)
3. is it possible to draw polyline, 3dpoly on a wall and "strech" it to become an opening?
4. on drawing status bar..there is a elevaton and cut elevation. I get what cut elevation stands for, but the other? (the lower elevation)
View 1 Replies
ADVERTISEMENT
Jun 3, 2013
I can make a curved wall, now I need to make a "cylinder" wall or a closed curved wall. If a curved wall can be closed I cannot figure it out.
View 4 Replies
View Related
Dec 7, 2011
I'm attempting to create a wall style that has 2 components, a framed wall and a brick veneer. What I would like to do is have this wall react a certain way when I insert a window. Basically, I don't want the window to cut into the brick veneer, only the framing.
I have attached my attempt so far, and I have not figured out how to get the window to only cut the framed portion.
View 1 Replies
View Related
Jun 12, 2012
I am having trouble cleaning up different wall types joining at or close to a corner. I tried to over ride the clean up radius....no luck.
View 9 Replies
View Related
Apr 14, 2011
I can convert a wall to a curtain wall but not a curtain wall to a wall. When converting a wall to a curtain wall I select wall in the design pallette right click apply to wall select the wall and it changes to a curtain wall. When I try converting a curtain wall to a wall I right click on curtain wall select apply properties to wall then go to select the curtain wall but I cannot select the curtain wall as a wall?
I simply want to convert an existing curtain wall to another wall type how is that done/
View 1 Replies
View Related
Oct 10, 2011
I want to draw 3D pipe line using sweep command. For this first i have to make a path in poly line, that i couldn't yet.
Check attached file green and red line and make a single poly line instead of 2 red or green line.
View 1 Replies
View Related
Aug 30, 2012
what's the best way to draw pipe, say 20" dia with .594 wall thickness in 3d?
View 9 Replies
View Related
Nov 28, 2012
I have forgotten how to draw a line that is parallel to a building wall which is not either horizontal or vertical.
View 9 Replies
View Related
Aug 21, 2013
I have a list of offset distance from centerline on both sildes (left and right). I want to use this to create a polyline that represents the daylight. these offsets are taken from an old hardcopy drawings of cross-sections. is there any way to draw this polyline that follows the alignment?
file can be .txt or .csv
View 3 Replies
View Related
Mar 7, 2012
is there a way to draw a polyline and have autocad clip everything outside of that polyline and discard it so that i end up with a smaller drawing. only the information in that polyline, nothing outside of the polyline
View 3 Replies
View Related
Nov 13, 2013
i need a vlisp program to draw polyline between two blocks.
View 3 Replies
View Related
Apr 25, 2012
I have a inserted block with 4 tags for Length, Thickness, Elevation and Width.How can extract attributes tag values and draw a closed polyline + 2 internal lines, parallel to the block?
Block Name: ID_DATA
Tags: LEN, THI, ELE and WID.
Each internal line placed in a third width.
View 9 Replies
View Related
Jun 28, 2013
I continue learning....
(setq ins (vlax-ename->vla-object ( ssname sele cod)) nombre (vla-get-name ins) ) (setq bloque1 (vla-item (vla-get-Blocks (vla-get-Document ins) ) nombre ) ) (setq s_ent1 (vla-item bloque1 1)) (setq pt1 (vla-get-startpoint s_ent1 ))(setq pt2 (vla-get-endpoint s_ent11 ))(setq s_ent2 (vla-item bloque1 2)) (setq pt3 (vla-get-startpoint s_ent2 ))(setq pt4 (vla-get-endpoint s_ent2 ))(command "_pline" pt1 pt2 pt3 pt4 "c")
Why dont draw de _pline?
View 4 Replies
View Related
Sep 2, 2013
I have drawings with a lot of polyline objects. I need a routine which will draw multilines by coordinates of vertexes of this polylines. For example, if there is a pline with coordinates 10,10 - 20,20 i want to draw in other layer MLINE with the same coordinates. I know it's should be simple but can not gues how to do it. I've never used LISP before.
View 5 Replies
View Related
Apr 19, 2012
I used to be able to snap to the end of the linework that form the visual end or intersection of walls while grip dragging a wall of one style to another. For example, using a wallstyle as a countertop, I'd be able to drag it to the corner of a room and use object snap to the intersection. In ACA 2012, the object snap defaults to the justification plane of the wall even if that's not where the intersection snap is desired.
View 6 Replies
View Related
Sep 25, 2013
Before the Revit purists come back with 'Revit is not AutoCAD' - A rectangle is a polyline, a hexagon is a polyline, and Autodesk has seen fit to include these shapes in the Draw Panel.
If I'm creating a component in place, say a cabinet door, and it's elevation is an L shape (or any custom shape - this is for a wall of cabinetry with odd-shaped panels), why, under 'Edit Extrusion', do I have to draw each custom shaped extrusion profile with these goofy single lines? The command doesn't even continue in a sensible way.
View 2 Replies
View Related
Jan 23, 2013
I want to make my walls to be adjusted to the ceiling.
View 1 Replies
View Related
Nov 27, 2013
How to draw a railing over the top of a wall? when the wall's top face is irregular. See the attached image.
View 1 Replies
View Related
Mar 27, 2013
I quite often like to use the wall grips to adjust the length of a wall. This works really well accept for the occasional situation were I want to snap to the face of another wall rather than the justification line. I know that I can snap to the face of a wall rather than the justification line because I have some files that it works fine in and other files that it does not work in.
View 2 Replies
View Related
Aug 5, 2012
In Revit there is a tool to convert lines to walls including lines of an xrefed AutoCAD file. Is this feature available in ACA?
View 3 Replies
View Related
May 16, 2012
I did a drawing in ACA2011 sent it to my remote office where I have ACLT for mac 2013 (trial). Worked on the file,
had to explode the couple of walls I was editing, saved as 2011 or 2010 file.
When I open the file in ACA2011 I can not execute the wall tool. This is the message received:
Command: _AecWallAdd Command not allowed because drawing contains objects from a newer version of this application.
The new objects would be lines.
View 5 Replies
View Related
Mar 30, 2012
My boss wants me to make the most outside line of a walltype to be the heaviest pen. If I go to the properties of the wall and changethe boundary it changes the boundary of the item in the wall, each boundary independentfrom the other. Such as a wall made of the following: BRICK, AIR SPACE, SHEATHING,STUD AND GYPSUM BOARD. In this wall theexterior face of the brick and gypsum board need to be heavy.
View 4 Replies
View Related
May 24, 2012
have trouble moving doors or windows within a wall?
I am trying to move a door so that the door is flush with a face of wall. The prompts in acad do not match the instructions.
For instance; select door, okay. then from anchor panel select 'reposition within wall', okay a red line appears and prompt to 'select position on the opening'. okay so i click the face or side of door jamb then select a reference point. (guide says select point to measure to) and on and on. Door never moves.
it should be; select door, select reposition in wall, select reference point (interior, exterior, midpoint), select the desired location. Done.
Instead it is select this that and the other , measure from here, select, click.click click.
View 3 Replies
View Related
Mar 8, 2013
In AutoCAD Architecture 2012: when we insert standard windows in the wall, we usually get a wall break. After changing window size to small (2’ high), this wall break disappears in the plan, but still have it on isometric or perspective view.
View 1 Replies
View Related
Apr 30, 2013
Is it possible to create a wall in AutoCAD Architecture that will change in size along its length. At one end of the concrete wall the wall thickness is 12", at the other end the wall thickness is 24" thick. The wall will grow in size from one length to the other.
View 6 Replies
View Related
Jan 16, 2012
I have received some architectural models which were modeled in AutoCAD MEP and only have walls modeled as type Standard. Is there a way to transform Standard walls into cavity walls etc., giving wall makeup as you go - or do I have to re-model in order to get quality 2D cuts?
View 1 Replies
View Related
Oct 21, 2013
I'm just trying to put a wall under a stair and it seems like I can not succeed. Already tried with interference, body modifiers and trimming.
View 2 Replies
View Related
Feb 29, 2012
Why would a window not go into a wall?
I have a client who is having this issue - when I open the file it works fine for me.
Is there a system variable or setting that could cause this?
View 9 Replies
View Related
Apr 11, 2013
I've got a wall style that has multiple components. I have changed one component so the bottom starts 12" below the baseline ht of the wall.The section window display reflects the change, but the wall style won't update.Is there a setting I'm missing somewhere.
View 2 Replies
View Related
Dec 16, 2008
How to group wall types together when scheduling a drawing?
I have multiple wall types within a drawing but scheduling produces multiple entries per type depending on length, only grouping them together when lengths are identical. All I need is a total length per wall type within the drawing.
View 5 Replies
View Related
Mar 18, 2013
I've been having an issue with autocad architecture 2013. For some reason it won't let me create a wall. I can click it but it doesn't want to actually create anything. It just gives me the selection tool. I downloaded the service pack and still doesn't work.
View 3 Replies
View Related
