I've been having an issue with autocad architecture 2013. For some reason it won't let me create a wall. I can click it but it doesn't want to actually create anything. It just gives me the selection tool. I downloaded the service pack and still doesn't work.
View 3 Replies
I am working in Arch Desktop 2011 and need to make a wall for a upper floor and roof line with different plate heights. See the attached drawing for explanation.
What I'm trying to do is create an upside down "V" wall to fill in this area. This is an as-built drawing for an existing house with an addition.
I am trying to use a pline to create an open ended wall. When I try to 'calculate automatically' by selecting a pline the width of the wall (2 components 8" wide total) the dialogue comes up and asks which component I want to apply the endcap to. I want to apply it to both, but don't seem to have that option.
View 2 Replies View RelatedIs there a way to create a window that slides into a pocket in a wall the way a pocket door does?
(I'd define a pocket door style for it but I'd like it to appear as a window for tags and schedules.)
way to create a gypsum board wall with the metal fittings inside?
I mean to have the fitting for example every 60 cm/ 25 in, and the metal frame on top and bottom of it.
Is there any similar wall in the ACAD architecture tools palette?
it's possible to create a barrel vault skylight that would work similar to a curtain wall (i.e. stretch the skylight and it adjusts to a fixed size and adds mullions)?
View 1 Replies View RelatedI can make a curved wall, now I need to make a "cylinder" wall or a closed curved wall. If a curved wall can be closed I cannot figure it out.
View 4 Replies View RelatedI'm attempting to create a wall style that has 2 components, a framed wall and a brick veneer. What I would like to do is have this wall react a certain way when I insert a window. Basically, I don't want the window to cut into the brick veneer, only the framing.
I have attached my attempt so far, and I have not figured out how to get the window to only cut the framed portion.
I am having trouble cleaning up different wall types joining at or close to a corner. I tried to over ride the clean up radius....no luck.
View 9 Replies View RelatedI can convert a wall to a curtain wall but not a curtain wall to a wall. When converting a wall to a curtain wall I select wall in the design pallette right click apply to wall select the wall and it changes to a curtain wall. When I try converting a curtain wall to a wall I right click on curtain wall select apply properties to wall then go to select the curtain wall but I cannot select the curtain wall as a wall?
I simply want to convert an existing curtain wall to another wall type how is that done/
I want to create a profile/wall style or what ever you want to call it for a raised deck flooring for external decking. I am looking at the decking material only. Not concerned about the timber framing sub floor material.
View 1 Replies View RelatedI'm using Architecture 2011 trial and it generates good rendering, but after adjusting sun angle (time), I received a message: Make sure the destination directory is writable and that the disk is not full. Rendering aborted.
View 1 Replies View RelatedI used to be able to snap to the end of the linework that form the visual end or intersection of walls while grip dragging a wall of one style to another. For example, using a wallstyle as a countertop, I'd be able to drag it to the corner of a room and use object snap to the intersection. In ACA 2012, the object snap defaults to the justification plane of the wall even if that's not where the intersection snap is desired.
View 6 Replies View RelatedI quite often like to use the wall grips to adjust the length of a wall. This works really well accept for the occasional situation were I want to snap to the face of another wall rather than the justification line. I know that I can snap to the face of a wall rather than the justification line because I have some files that it works fine in and other files that it does not work in.
View 2 Replies View RelatedIn Revit there is a tool to convert lines to walls including lines of an xrefed AutoCAD file. Is this feature available in ACA?
View 3 Replies View RelatedI did a drawing in ACA2011 sent it to my remote office where I have ACLT for mac 2013 (trial). Worked on the file,
had to explode the couple of walls I was editing, saved as 2011 or 2010 file.
When I open the file in ACA2011 I can not execute the wall tool. This is the message received:
Command: _AecWallAdd Command not allowed because drawing contains objects from a newer version of this application.
The new objects would be lines.
My boss wants me to make the most outside line of a walltype to be the heaviest pen. If I go to the properties of the wall and changethe boundary it changes the boundary of the item in the wall, each boundary independentfrom the other. Such as a wall made of the following: BRICK, AIR SPACE, SHEATHING,STUD AND GYPSUM BOARD. In this wall theexterior face of the brick and gypsum board need to be heavy.
View 4 Replies View Relatedhave trouble moving doors or windows within a wall?
I am trying to move a door so that the door is flush with a face of wall. The prompts in acad do not match the instructions.
For instance; select door, okay. then from anchor panel select 'reposition within wall', okay a red line appears and prompt to 'select position on the opening'. okay so i click the face or side of door jamb then select a reference point. (guide says select point to measure to) and on and on. Door never moves.
it should be; select door, select reposition in wall, select reference point (interior, exterior, midpoint), select the desired location. Done.
Instead it is select this that and the other , measure from here, select, click.click click.
In AutoCAD Architecture 2012: when we insert standard windows in the wall, we usually get a wall break. After changing window size to small (2’ high), this wall break disappears in the plan, but still have it on isometric or perspective view.
View 1 Replies View RelatedIs it possible to create a wall in AutoCAD Architecture that will change in size along its length. At one end of the concrete wall the wall thickness is 12", at the other end the wall thickness is 24" thick. The wall will grow in size from one length to the other.
View 6 Replies View RelatedI have received some architectural models which were modeled in AutoCAD MEP and only have walls modeled as type Standard. Is there a way to transform Standard walls into cavity walls etc., giving wall makeup as you go - or do I have to re-model in order to get quality 2D cuts?
View 1 Replies View RelatedI'm just trying to put a wall under a stair and it seems like I can not succeed. Already tried with interference, body modifiers and trimming.
View 2 Replies View RelatedWhy would a window not go into a wall?
I have a client who is having this issue - when I open the file it works fine for me.
Is there a system variable or setting that could cause this?
I've got a wall style that has multiple components. I have changed one component so the bottom starts 12" below the baseline ht of the wall.The section window display reflects the change, but the wall style won't update.Is there a setting I'm missing somewhere.
View 2 Replies View RelatedHow to group wall types together when scheduling a drawing?
I have multiple wall types within a drawing but scheduling produces multiple entries per type depending on length, only grouping them together when lengths are identical. All I need is a total length per wall type within the drawing.
I have two created wall styles, one is a stud wall with gyp bd each side, the other is a cmu wall with gyp bd each side. I want to use a solid hatch which I am able to do but the problem is one wall style the stud hatch is HATCH 1 and in the other wall style the CMU hatch is HATCH 2. It seems as though the two wall styles are tied together some how for if I turn on / off a hatch in one of the wall styles it turns on / off the hatch in the other wall style.
View 4 Replies View RelatedAnother little problem off the big list. Up until now i have been using Autocad Architecture 2009 but recently upgraded to 2012. For some reason though, my hatches are now no longer linking on wall corners like the attached drawing shows.
View 2 Replies View RelatedI have a curtain wall I need to make, but I need it to be curve on elevation. Its an arch. I can do it on sketchup but I need autocad precision to establish the modules. I have this division settings, horizontal 3.111 vertical 3.559m.
The profile arch has a 40.062m radius. 27.741 arc length. and a total angle of 39.673.
My question is, how can I bend the curtain wall??? I can make a flat curtain wall to follow my referenced base curve, but I need tu curve it in elevation. Here is a demo view from sketchup.What i'm trying to do is the coloured face.
I'm trying to draw a wall in plan that has Wood Timbers in the corner. The problem im having is that if i use a Body Modifier it puts dark heavy lines within the wall. And Plan modifiers don't seem to be working. I tried to use an interference condition and that also did not do the trick.
I tried to force a cleanup and that did not work either.
How to reposition window within wall? i have a window put into my basement wall with footing as shown. unfortunately, the window aligns on the symmetry line of footing itself (as i believe the footing is taken as the overall wall thickness). i want the window to be aligned on the wall/cavity thickness only.
i prefer to have it default in this window or wall style rather than playing around with anchors and other ,,reposition tools'' for each and single window in my basement plan.
In model space, my walls all show with correct colors. However, when I go into a tab, the viewport is showing my walls in different colors than what I have specified. There are no overrides within the viewport. The display is 2D wireframe. If I change the display to 3D wireframe, the colors change to the correct ones, but the dimension hashes are also in wireframe, not filled. Why the 2D display is changing my wall colors and how I can change these to show as I want them to?
View 9 Replies View Related
