I've got a wall style that has multiple components. I have changed one component so the bottom starts 12" below the baseline ht of the wall.The section window display reflects the change, but the wall style won't update.Is there a setting I'm missing somewhere.
View 2 RepliesWhen building wall styles and configuring cleanup priorities for components, what is the methodology? Do I sketch out a bunch of scenarios of various wall styles meeting each other at Ls and Ts and crosses and whatever, and then try to puzzle it all out: "if I set the outer airspace to 400, then when it gets to this T, the airspace will cut through the rigid insulation with its 600 priority, but will get cut through by the sheetrock with its 200 priority....". That seems like a recipe for headaches. So instead, do I just start from one side of a wall (the wall with the greatest number of components, I guess) and assign the lowest priority number (300, say) to the structural component, the highest number (1200, say) to the finish material component, and numbers in between for everything else, and then see how it works, tweaking by trial and error? The table of priority numbers for various materials provided is useful, but I'd like to have a better understanding of how those numbers might have been derived, so I can do a better job of assigning my own numbers to components that don't appear in the list.
Also, if a wall type contains two components of the same material (I'm thinking of the layers of rigid insulation on either side of the concrete in an Insulated Concrete Foundation system), should those two components have the same priority number (probably not), or different ones (seems more likely)?
I can make a curved wall, now I need to make a "cylinder" wall or a closed curved wall. If a curved wall can be closed I cannot figure it out.
View 4 Replies View RelatedI'm attempting to create a wall style that has 2 components, a framed wall and a brick veneer. What I would like to do is have this wall react a certain way when I insert a window. Basically, I don't want the window to cut into the brick veneer, only the framing.
I have attached my attempt so far, and I have not figured out how to get the window to only cut the framed portion.
I am having trouble cleaning up different wall types joining at or close to a corner. I tried to over ride the clean up radius....no luck.
View 9 Replies View RelatedI can convert a wall to a curtain wall but not a curtain wall to a wall. When converting a wall to a curtain wall I select wall in the design pallette right click apply to wall select the wall and it changes to a curtain wall. When I try converting a curtain wall to a wall I right click on curtain wall select apply properties to wall then go to select the curtain wall but I cannot select the curtain wall as a wall?
I simply want to convert an existing curtain wall to another wall type how is that done/
I am tryng to upgrade from LT 2009 to LT 2012 and recieve this message "annot update some system component now. Please reboot the machine and try again" We are running Windows Professional XP 2002 with SP3.
View 3 Replies View RelatedWhen I try to replace a component in Inventor 2014. It replaces it but does not update the tree in the browser. I have to manually delete the part and place a new one in.
View 9 Replies View RelatedI would like to create a family component using the wall foundation bearing footing as a template. I cannot find the file where the templates are located. I tried using the structural footing template but it would not give me the same flexibility the wall foundation bearing footing template does.
View 2 Replies View RelatedIn assigning a material for a new wall exterior component, I see no other material option other than brick, yet there are many materials sutable.
View 3 Replies View RelatedI was able to bring in custom curtain wall panels as legend components-- however, when I set the host length, the height is automatically the same. Is there a way to insert a curtain wall panel into a legend that will have a rectangular shape (in my case, taller than it is wide)?
View 1 Replies View RelatedI'm trying to make a Wall Types Legend using the Legend function in 2011. I did the first wall type just fine, placed it in section, tagged the material, etc. Now when I go to place another wall in a section view, it tells me the component is not visible in selected view. They are both new construction phase, stacked walls.
View 3 Replies View RelatedI just started using version 2010 (I was using 2009 way past the 2010 release). Whenever I go to insert a detail component such as a 3/4" bolt it fails. On the command line I see the name of the detail to be inserted but immediately after is *Cancel*.
I have to shut down Architecture and restart it before it will let me insert the component -- and then only once. If I want to insert other components I have to shut down and restart every time.
I inserted a design component of a concrete wall and the hatch pattern came in with ansi31 instead of a concrete pattern and it is filled in. I dragged another wall style from tool palette and instead of the conc pattern, I'm getting the ansi31 pattern. Also tried the 3" base course with a gravel pattern and got the same thing.
View 7 Replies View RelatedThe AEC content folders are missing. Actually, it's not missing but autocad is not able to locate them.
C:ProgramDataAutodeskACA 2012enuAEC Content.
C:ProgramDataAutodeskACA 2013enuAEC Content.
Is there any problem or bugs with the "AecDtlComponents.mdb" file type
How do you modify the database and generate the size of items needed within the software from the Detail Component Database? Can you Adjust sizes? Are there more items to select?
View 1 Replies View RelatedWe are using Autodesk Architecture 2013 running on 64bit Windows 7 workstations. When I try to access the Detail Component Database I get an error message stating the AecDtlComponents (US).mdb will not open. I went into Tools-->Options-->AEC Content and tried to Add/Remove a database but the list was empty. When I try to Add a database I get the same error message AecDtlComponents (US).mdb will not open.
View 5 Replies View RelatedI recently installed Building design suite premium and I am just getting around to getting it configured. I was trying to open up the detail component manager and have been looking for the default tool palletes for detailing and they are missing. In AEC content the path to the databases are there but I can't find where to access the detail component manager or tool palletes. I can't even find the tool catalog to bring them in that way. It says to look for the detail panel in the ribbon but guess what, I don't have that panel nor do I have the option to show it in the ribbon.
I have also searched for a command line command to open the manager and I couldnt find that either.
We are running ACA 2001 on WIndows Vista 64 bit. The Detail Component Manager will not open on (2) of our (7) machines and returns the error message: "Specified cast is not valid". The files are located on each machine. I have tried running a repair; I have copied the Detail Component Manger files over from the good machines, and I have also run a re-install and the Detail Component Manager still will not work.
View 6 Replies View RelatedMy detail component manager in AutoCAD Architecture 2011 was working fine until I installed Revit 2013 on it (as part of Building Design Suite 2013). I have tried uninstalling and reinstalling MS .Net framework, but it has not worked.
View 2 Replies View RelatedI used to be able to snap to the end of the linework that form the visual end or intersection of walls while grip dragging a wall of one style to another. For example, using a wallstyle as a countertop, I'd be able to drag it to the corner of a room and use object snap to the intersection. In ACA 2012, the object snap defaults to the justification plane of the wall even if that's not where the intersection snap is desired.
View 6 Replies View RelatedWe installed ACA 2012 a few weeks ago on computers running Windows Vista Business 64-bit. On one of our machines, the Detail Component Manager was working fine and now when we go to insert an object the insertion fails with a *cancel* appearing on the command line.
I have checked all of the file paths and folder permissions and everything is fine. Microsoft.Net Framework 4 Client & Extended is installed as along with Microsoft.Net Framework 3.5 SP1.
I quite often like to use the wall grips to adjust the length of a wall. This works really well accept for the occasional situation were I want to snap to the face of another wall rather than the justification line. I know that I can snap to the face of a wall rather than the justification line because I have some files that it works fine in and other files that it does not work in.
View 2 Replies View RelatedIn Revit there is a tool to convert lines to walls including lines of an xrefed AutoCAD file. Is this feature available in ACA?
View 3 Replies View RelatedI did a drawing in ACA2011 sent it to my remote office where I have ACLT for mac 2013 (trial). Worked on the file,
had to explode the couple of walls I was editing, saved as 2011 or 2010 file.
When I open the file in ACA2011 I can not execute the wall tool. This is the message received:
Command: _AecWallAdd Command not allowed because drawing contains objects from a newer version of this application.
The new objects would be lines.
My boss wants me to make the most outside line of a walltype to be the heaviest pen. If I go to the properties of the wall and changethe boundary it changes the boundary of the item in the wall, each boundary independentfrom the other. Such as a wall made of the following: BRICK, AIR SPACE, SHEATHING,STUD AND GYPSUM BOARD. In this wall theexterior face of the brick and gypsum board need to be heavy.
View 4 Replies View Relatedhave trouble moving doors or windows within a wall?
I am trying to move a door so that the door is flush with a face of wall. The prompts in acad do not match the instructions.
For instance; select door, okay. then from anchor panel select 'reposition within wall', okay a red line appears and prompt to 'select position on the opening'. okay so i click the face or side of door jamb then select a reference point. (guide says select point to measure to) and on and on. Door never moves.
it should be; select door, select reposition in wall, select reference point (interior, exterior, midpoint), select the desired location. Done.
Instead it is select this that and the other , measure from here, select, click.click click.
In AutoCAD Architecture 2012: when we insert standard windows in the wall, we usually get a wall break. After changing window size to small (2’ high), this wall break disappears in the plan, but still have it on isometric or perspective view.
View 1 Replies View RelatedIs it possible to create a wall in AutoCAD Architecture that will change in size along its length. At one end of the concrete wall the wall thickness is 12", at the other end the wall thickness is 24" thick. The wall will grow in size from one length to the other.
View 6 Replies View RelatedI have received some architectural models which were modeled in AutoCAD MEP and only have walls modeled as type Standard. Is there a way to transform Standard walls into cavity walls etc., giving wall makeup as you go - or do I have to re-model in order to get quality 2D cuts?
View 1 Replies View RelatedI'm just trying to put a wall under a stair and it seems like I can not succeed. Already tried with interference, body modifiers and trimming.
View 2 Replies View Related