AutoCAD Civil 3D :: Corridor Item To Continue Past Daylight Along EG

Feb 4, 2013

I have a corridor design and the corridor daylights very close to the pavement.  I need to have rock from the EOP out beyond the daylight point to a 30' offset from the alignment.  I need it to follow the EG and show a depth of 2' throughout.

I had to draw the rock shapes manually.  But I'd like to figure out how to do it using the corridor if possible.

Please see the attached image.  Everything beyond the daylight point was traced on top of the EG and then offset 2' to get the bottom.

View 9 Replies


ADVERTISEMENT

AutoCAD Civil 3D :: Corridor And Assembly Daylight

Nov 14, 2013

I am creating a corridor with a simple assembly. On my assembly, I have basic lane and daylight Multiple surface. My target is existing ground.

View 9 Replies View Related

AutoCAD Civil 3D :: Corridor - Forcing A Fill Daylight

Jan 7, 2014

What is the best method of forcing a fill daylight using an assembly?  Though I've played with several links, I'm not managing to get the results I desire.

View 3 Replies View Related

AutoCAD Civil 3D :: Cannot Get Corridor Surface Boundary From Daylight Points

Jun 22, 2012

Cannot get corridor surface boundary from daylight points. Is there another way so that I do not have to trace the outer limits?

View 3 Replies View Related

AutoCAD Civil 3D :: Corridor Daylight Cut-Fill Feature Lines Jump Across

Sep 20, 2013

My corridor Feature Lines for Daylight Jump across in different areas (see attached PDF)

when I look at it in 3d it looks ok but the plan view the jumped lines show up.

View 4 Replies View Related

AutoCAD Civil 3D :: Corridor Section Editor Not Displaying Daylight Lines To EG Surface

Jul 13, 2012

I'm having a random issue with the daylight ties lopes not tieing to the EG surface at all stations in the Corridor Section Editor. Some stations daylight fine. In plan view the daylight lines vary left & right as expected but don't display at all in Section Editor.
 
Some background info:2012 Civil 3D SP1 / 64 bit / WIN7Simple corridor used1 alignmentSame fg profileSame drefd EG surface (set all targets for daylight LT/RT)Only one assembly applied to entire corridor Attached are 2 captions of the issue I'm having which each have a cut & fill occurrence as well as a caption of the entire align. & corridor. I did try deleting corridor & recreating and even recreated a simpler assembly and still have the daylight issue in same areas of corridor.

View 2 Replies View Related

AutoCAD Civil 3D :: Corridor Surface Boundary - Line Is Jumping On Daylight Fill

Jun 22, 2013

I have problem with corridor surface boundary , in curve boundary line is jumping on daylight fill , but i have created surface on wearing layer ,also when i am adding boundary there is only 3 types of adding , corridor extends , polygon and interactively , photo attached.

I am using Civil 3D 2014

View 4 Replies View Related

AutoCAD 2010 :: No Longer Copy / Past One Item From One Drawing To Separate Drawing

Dec 10, 2013

Eventually after I copy and paste with the clipboard enough times within one drawing, the ability goes away and I can no longer copy and past one item from one drawing to a separate drawing.  I need to use the clipboard function because that is the only way of getting an item from one drawing to another.  

I have download a clear clipboard function but it doesn't work. Closing CAD and restarting does not reinstate the function.  

View 5 Replies View Related

AutoCAD Civil 3D :: Surface Corridor Is Not Triangulating Entire Corridor Boundary

Sep 14, 2012

I have created a surface from a corridor.  I set the boundary of the surface to the daylight of the corridor.  In some areas of the corridor the surface does not triangulate see attached.

View 2 Replies View Related

AutoCAD Civil 3D :: Copy Corridor Or Corridor Station Values Only?

Dec 13, 2012

Copy a corridor successfully? I'd like to try this just a little worried about the explosion of evil this may cause to my Civil 3D session.

Even all the properties of the corridor setup from one to another would be useful. I'm building one corridor and an 2nd one that matches everything except I need to replace my Assembly with one meant for stripping.

View 9 Replies View Related

AutoCAD Civil 3D :: Corridor Surface Is Not Matching Corridor Top Links

Mar 21, 2013

My corridor surface is not matching my corridor top links.  see attachments.  this is affecting my volumes!

The section-plan(surface red).png is showing the section editor and the plan view.  the red highlighted line in section is the corridor surface and as you can see in plan view the surface is incorrect and wiggly.

The pdf is all my sections with the red linework being the corridor surface.

C3D ver 2012
Win 7, 64bit

View 2 Replies View Related

AutoCAD Civil 3D :: Can't Get Past DWT File

Jun 5, 2013

The last few days I've had issues opening C3D 2014. I'll start the software, the splash screen/window will appear and in the the lower left hand corner of it, you'll see C3D loading files. But when it gets to "Opening drawing....". Basically, opening my custom dwt. The software stalls. Won't open. Now I can go on any other computer in my office and C3D opens no problem using the same dwt.

View 5 Replies View Related

AutoCAD Civil 3D :: Cannot Get Daylight Link To Show

Apr 8, 2013

I have a corridor with conditional assembly for all 200 sections. One conditions which stretches 200 feet I can not get the daylight link to show in the sections.

View 9 Replies View Related

AutoCAD Civil 3D :: Cannot Mirror Daylight Subassembly

Apr 26, 2012

Why I can't mirror the Daylight Inside ROW Subassembly? For some reason I can only place it on the right side of my assembly and in the subassembly properties there is no option to flip it to the left. In the Modify Subassembly section when it's selected the mirror option is greyed out. 

What I am trying to accomplish seems simple enough:

I have a utility easement in a drainage ditch that is 30' wide with a sewer line designed down the center, we need a very simple 10' access road on the uphill side of sewer line with 4:1 Cut/Fill slopes on either side when possible, however when the 4:1 won't catch within the easement I need it to daylight within.

At first glance the Daylight Inside ROW seems to be the appropriate subassembly for this instance but I can't get it on the left side of my road.Is there a way to set up this parameter with a different subassembly because I can get other subassemblies on the either side just fine, for example, the Cut Slope Layout Mode subaasembly works but when I build my corridor with it the slopes tie outside of the easement in several locations.

Civil 3D 2012
Windows 7 Service Pack 1
Intel Core i7-2600 CPU
16GB RAM

View 5 Replies View Related

AutoCAD Civil 3D :: Daylight With Variable Slope

Nov 6, 2012

I wonder is it possible to have a daylight (or other function)  that can give a different slope for datum and for the top.  This would be useful for if you have different rules (e.g. because of geotech) with regard to temporary and permanent batter slopes.

View 7 Replies View Related

AutoCAD Civil 3D :: Make A Daylight Bench Right Before OG?

Jun 14, 2012

Is it possible to make a bench right before the daylight line meets the top surface (Original Ground)?

The Road prism is a tylical shape that has a u-shaped ditch on one side.  The daylight line from the outside edge of the ditch follows a series of comlicated benches at set elevations and then terminates at OG with no trouble but I'm trying to get an additional bench to be generated before OG (see attached + yellow lines). 

how to add this extera bench?

View 5 Replies View Related

AutoCAD Civil 3D :: Daylight To Surface Max Slope?

Apr 18, 2012

I'm modeling a simple corridor (12' lane 2%, 6' shoulder 6%, 4:1 to match EG).  I used the "LinkSlopeToSurface" subassembly for the 4:1 to match the EG.   Unfortunately our EG isn't always wide enough for the 4:1 slope to match it somewhere.

Is there an assembly that would use 4:1 as a standard daylight slope, but where necessary adjust the slope, max. 3.5:1, to match EG surface? 

View 5 Replies View Related

AutoCAD Civil 3D :: Transition Between Daylight Regions

Sep 12, 2013

I am working on a project where some of the corridors require different daylight slopes. I need to transition between a region with 2:1 slope to a 10:1 slope. My local civ3d support said something about using grading tools to achive that.

What I understood was that my assemblies should not have any daylight sub-assembly and that i should grade the corridor and than add a transition zone between the different gradings. Did I understand correctly?

View 9 Replies View Related

AutoCAD Civil 3D :: Polyline To Draw Daylight Line

Aug 21, 2013

I have a list of offset distance from centerline on both sildes (left and right). I want to use this to create a polyline that represents the daylight. these offsets are taken from an old hardcopy drawings of cross-sections. is there any way to draw this polyline that follows the alignment?

file can be .txt or .csv

View 3 Replies View Related

AutoCAD Civil 3D :: Daylight To Offset With Maximum Slope?

Nov 7, 2012

I need to daylight to an offset, to create a clear zone/fall zone, but it must have a maximum slope of 6:1. If no daylight is found at the offset and maximum slope, then grade at the maximum slope to the offset then daylight to the target suface at a steeper slope.

View 9 Replies View Related

AutoCAD Civil 3D :: Variable Daylight Slopes To A Profile

Dec 24, 2013

I am trying to create in my sub assembly a daylight with a variable slope to a graded ditch then it back slopes to natural ground. (image attached). How can I do this in Civil 3d 2012?

View 9 Replies View Related

AutoCAD Civil 3D :: Daylight Not Included In The Boundaries List?

Dec 21, 2013

I got this problem during creation of corridor surface boundaries. I would like to create a corridor datum surface using the daylight feature lines, automatically from the corridor surfaces-boundaries dialog box, but the daylight does not appear in the list.

View 5 Replies View Related

AutoCAD Civil 3D :: Grading Object / Daylight Lines

Sep 19, 2013

Where are the setting for the display for grading lines such as features, daylight lines, etc in the standard grading pallet?

View 1 Replies View Related

AutoCAD Civil 3D :: How To Use Daylight Basin For Creating Ditch

Aug 21, 2013

how to use daylight basin, for creating ditch

View 3 Replies View Related

AutoCAD Civil 3D :: Subassembly Feature At Daylight Line

Feb 20, 2013

I have been asked to put a feature (a diversion berm) at the daylight line of a roadway where cut conditions exist off the proposed shoulder.  Because of the length of the project, it would be useful if this could be done automatically as part of the corridor, rather than creating a feature line from the daylight line and grading it separately. 

Is there a way to continue an assembly past the initial daylight line and make it conditional to cut situations? 

View 8 Replies View Related

AutoCAD Civil 3D :: Daylight Assembly - Fill / Cut Condition

Apr 8, 2012

I like to create a daylight assembly with following criterias

Fill/cut Condition

1. Target to surface 2.5% slope

2. If the surface is not met within 19 m from centreline, then till 19 m 2.5% slope and 33% slope afterwards till it hit the surface.

Civil3D 2012

View 2 Replies View Related

AutoCAD Civil 3D :: Daylight General - Which Priority To Standing Water

May 2, 2013

Original intent was for daylight to have 4:1 slope and keep within the R/W. This causes some areas to hold water as shown circled in the image. I know I should be able to give it parameters or targets to avoid this. 

View 1 Replies View Related

AutoCAD Civil 3D :: How To Provide Multiple Daylight Subassemblies With One Assembly

Jul 24, 2013

Have a question regarding multiple daylight subassemblies, don't know if it is possible.  So I have an assembly with a trench SA in cut condition and a project to surface in fill condition, I built the corridor with this assembly and most of things look fine.  However, there is a short stretch (in cut condition) of the corridor that I would like to modify such that a trench is not provided.  I know I can create a new assembly with my desire condition, then create a new region and drop that assembly there, but I am wondering if there any other way to achieve my goal without another assembly.

View 8 Replies View Related

AutoCAD Civil 3D :: Finding Drain Pipe Daylight Locations

Aug 21, 2013

I need to rough in a drainage pipe network that connects several structures around a site. The pipe inverts need to be 6.5' below the finished floor of each unit and must maintain a minimum 2% slope. The network needs an outfall at some undetermined point on the site. The pipes must follow some existing roads, so they are not interconnected directly to each structure.

How can I go about determining the potential outfall locations?

View 3 Replies View Related

AutoCAD Civil 3D :: Add Daylight Subassembly In Order To Grade Surface?

Oct 1, 2013

I'm building up my assembly and I want to add a daylight sub-assembly in order to grade my proposed surface to the existing surface. Typically I would have a 1:3 slope up or down. I have choosen the DaylightGeneral for this and although there is quite a few parameters to play with, I'm only interested in the up/down slope but when I put anything sleeper than 1:4 it doesn't work, I get this red line and circle.

View 4 Replies View Related

AutoCAD Civil 3D :: Daylight Lines Intersect At Turn Segments

Jun 20, 2012

I've created a corridor with a Cul-de-sac. The problem is that the daylight lines targeted to the existing ground intersect at turn segments: 

which results in defects of corridor surface:

I wonder if there's a way to overcome this.

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved