I have my design drawing referenced into another drawing for plan and profile sheets. I made some changes to my pipe network in my design drawing, and my manhole profile labels disappeared in my sheet drawing!
The manhole labels in plan view stayed where they were, and updated with the changes I made. The profile labels just disappeared.
problem labelling manholes when using the 2013 ukie template? - pipe labels show up but nothing else.
If I open the label style composer it looks fine in preview, visibility is set to true and its on the same layer as the pipe labels so should display OK. It seems to be a template setting though because if I open the metric or imperial templates and draw a network the labels all work. if I can find the right tick box it would be quicker than labelling with mtext.
I have a sanitary run manhole to manhole with null structures in between for lats. Each null is named "wye(lot#)" which I really do not need labeled anywhere but grants me the illusion of order and control. When I label the manhole (style uses text for each component) it references the inverts as from adjacent structure the nearest of which is the null. I need it to reference the upstream manhole as the from structure. BMP?
Another issue is the text for each component. There are times when I need to have the manhole label show "INV 8" IN 209.50 Int Drop (MH110)" or "INV 8" IN 208.75 w/ Slide (MH 108)". But as you know if I add to one I add to all. I found a post that discussed editing the xml to do this but my code either looked different than the example or I was looking at it cross eyed. I think if I could add an invert type column to the structure properties pipes tab the text for each component could add it to the label.Is there a better way people have been handling this?
I remember seeing an article or web cast on how to create a style to display a single line for a manhole. It may have been about using the parts create tool. But for the life of me, I can’t remember where I saw it.
Also I had created a style in C3D2007 to display the pipes in profile as a single line. This was done by drawing the flow arrow in a non printable colour over the top of the pipe.In C3D2008 this is no longer possible. So now what?
C3D 2009. I have a style that labels the pipe diameter in section view and the type of pipe. When I label the pipe everything shows up fine. Save the drawing and re-open and my labels are gone. I can see them when is opening but after it regenerates, gone. All layers are on display set to true. Tried too many different things and no success. This issue only happens in two drawings.
View 9 Replies View Relatedacad c3d 2013
My sag and Crest profile labels disappear when opening the drawing.
I would live to label the PVI on my Profiles but not show the PVI label at the start and end of my profile. How to set this?
View 1 Replies View RelatedI would like to have the leader arrow attached to the rim of the structure in profile view. Now they are attached along the side of the structure well below the rim. This is for the dragged labels. How can I adjust the arrowhead attachment point?
View 1 Replies View RelatedHow to "NOT" label the top elevation in a profile view? (see attached pic)
I can live with the far right and left vertical labels if I could turn the top elevation off.
Civil3D 2014 SP1
Win 7 Professional - 64-bit
HP Z400
Xeon W3550 @ 3.07Ghz
24GB of RAM
Nvidia GeForce GTX 760
Having problems with the spanning pipe labels in profile. Sometimes it works fine and others not at all. It will let me pick the two structures at each end and highlights the pipes, but then it will not let me pick the pipe to place the label on.
View 5 Replies View RelatedI click on my pipe in profile. Right click and add label. I see nothing, no label. All layers on and un-frozen.
View 6 Replies View RelatedI have labled for grade break on the profile, but it did not lable all break line? how to add grade breaks along the new profile (see attached image).
View 1 Replies View RelatedI have C3D 2013 and recently my profile labels for sag and crest vertical curves are disappearing. When I first open the drawing and the program goes through loading I can see the labels but once it stops loading they disappear. All my levels are on, I have ran an audit several times, I have deleted the labels in the manager and replaced them but once I save and quit they are no longer visible. I am able to see the labels through an xref of the drawing but it appears that the labels have been reset to their default position and not where I had adjusted them to view them within the viewport. I have attached pictures of what it looks like.
View 9 Replies View RelatedI just created a profile by choosing my PVIs and linking them together with tangent curves. How do I add labels to show the vertical curve properties (K value, curve length, station of PVI, elevation of PVI...)? I'm guessing I have to edit the label style?
View 2 Replies View RelatedIf I have a pipe that spans between two profile views, is there a way to label the pipe in each profile view with only the lineal feet that is showing in that profile view?
View 4 Replies View RelatedIs there a way to get the ProfileBandLabelGroup labels from a profile view. I see I can get the ProfileViewBandItems, but don't see a way to convert it into the labels. I'm looking to override the text components. The code below does that, it's just getting the object without having to have the user select it.
ProfileBandLabelGroup labels = ssResult.ObjectId.GetObject(OpenMode.ForWrite) as ProfileBandLabelGroup;
LabelStyleTextComponent textComponent = labels.GetAt(0).GetTextComponentIds()[0].GetObject(OpenMode.ForRead) as LabelStyleTextComponent;
Autodesk.Civil.DatabaseServices.LabelGroupSubEntity label = labels.GetAt(0);
label.SetTextComponentOverride(textComponent.ObjectId, "blue");
I have a profile view created with several surfaces including a proposed surface. The stationing on the X-Axis of the profile view corresponds correctly with the PT's, PC's etc on the proposed surface profile, however the the labels that are actually on the profile line are giving me values such as PC: 0+668.62 when it should read 21+93.63.
I can't seem to find a correlation in the two numbers and am having difficulty changing the style to correctly reflect the stationing.
I tried moving a Profile View and even though I selected everything at once and selected a base point and destination point, the Profile View Station and Elevation labels moved with a different offset than the Profile View itself. ?
Civil 3D 2012
What is causing my EG Data Reference Surface to disappear on screen and Profile goes to crap? I've noticed this twice on same project in separate drawings. If I go to Toolspace and synchronize then it appears back on screen.
First dwg: I created a Pump Station Site Plan and data referenced in my surface and pipe network. I save and close then reopen and EG is gone until I synchronize.
Second dwg: I created a Railroad Crossing Exhibit showing plan and profile. I data referenced in my surface and pipe network. Same thing...save, close, reopen and I have to synchronize it to have plan and profile to appear ok.
This isn't good when I have .dsd files that I typically plot my drawing package from. I sent multiple sets of drawings to the plotter and all my Pump Station Site Plans were missing the surface contours. For this sheet, I had to synchronize and send separate plots just to have contours appear.
We sre doing 3 line profiles for a road and the left and right curb should be .13' lower than the centerline elevation. In many cases we are getting .14' or sometimes more or less. We tried resampling the cooridor with a tighter interval but still the same results.
View 9 Replies View RelatedI cannot for the life of me get the start and end labels for any band to display within a profile view. Each band has the 'label start' and 'label end' labels ticked and the major/minor labels display at every other point but don't display anything at the start of the view or end. The profile views are taken from a simple straight alignment and the profiles themselves extend the full length of the view.
View 9 Replies View RelatedI am running CV3D 2011 on a Windows 7 64 bit workstation. I have a road profile that has a band which labels the existing and proposed profile elevations. For some reason the profile band labels (including the stations) randomly disappear and all you see is the band box. If you REgen they will reappear but will dissapear again when you plot preview and they WON"T plot...even though they are there in the drawing!
Civil 3D 2013 SP2 | Win 7 64-bit SP1
Intel Core i5-2500 @ 3.30GHz, 8GB Ram | ATI Radeon HD 5450
I was looking at placing pipe information into a Profile Band. I see that I can include the following properties in a pipe label in the profile band:
<[Total Slope Across Span(FP|P2|RN|AP|GC|UN|Sn|OF)]>
<[Number of Pipes in Span(GC|UN|Sn)]>
<[Drop Across Span(Um|P2|RN|AP|GC|UN|Sn|OF)]>
Only problem is they don't actually give me the information of a spanning pipe, only a single pipe. I see no way of choosing which pipes will be spanned. Am i missing something in the creation of the profile band that allows me to choose the spanning pipes or is this broken?
Is there a way in C3D to add elevation information from a profile to an alignment label? What I'm trying to do is add labels to an alignment in a plan view with elevation information from a profile design associated with that alignment at a particular station. For example, the note would read:
ALIGNMENT B
STA: 12+83.67
ELEV: 435.87
I can't figure out how to add any elevation data to the alignment note. I really don't want to have to create a section and a corridor surface, but that's the only way I can think of right now... and I'm not sure that would actually let me add a station and elevation in the same note in a plan view.
On our road profiles, we have to show that low points and high points are adjusted to maintain a minimum of 0.6%. see attached screen shot. Currently, I am calculating the adjusted low point and editing the profile label. Since I can't figure out how to edit one label in a data band, I've been wiping out the old elevation and typing in the new elevation over it.
Is there a way to get C3D to do the calculation for me and populate the labels with the adjusted elevation?
Civil3D 2013
Windows 7
C3D2011
Say you have a feature line in plan view and you project it to profile view. Is there a way to label the true slope of the projected feature line segments in profile?
The profile view depth labels are not accurate since it's simply calculating the length from station to station in profile.
...and of course this does not correspond to the true segment length since the feature line is not parallel to the alignment.
Any way to label my structures in profile with a vertical line that shows the structure ID, Station number, invert data, etc. all on an adjustable length line. Ive got it worked out for how to show it on a fixed length line, but the problem is when you have multiple structures in close proximity the labels tend to overlap. Dragging the labels upward pull the leader line compnent with them and they do not remain anchored to the structure. When I say leader, I am not referring to the dragged state as that creates a leade with a landing at an angle. What I really want is a line component that stay perfectly vertical and remains anchored to the structure insertion point even though I drag the text of the label upward. Is there a way to do this? Seaching the internet and reviewing ym texts has yet to yield an answer.
View 7 Replies View RelatedI've attached an image of a storm drain invert label for a storm drain profile. As you can see, the middle manhole has all three inflow pipes labeled. Is there a way to only label the inverts of the two pipes shown in the profile view?
C3D 2014
Windows 7 64-bit
I have a large scale industrial project with multiple road profiles and sections sheets. I find that when I plot my drawings manually by opening the drawing everything comes out fine. But when I publish the drawings manually or thru Sheet Set Manager, it shifts my vertical curve labels on my profiles down, which then conflicts with the profile linework (see attached image). Unfortunately manually plotting these drawings is not an option. Because of the amount of information in each drawing it takes 3-4 mins to open and we have 200+ drawings in a single set of drawings, which we have multiple sets of drawings for the project.
View 2 Replies View RelatedI'm looking for a way to add a marker with location & elevation data to the profile (not the bands).
Only mention i found in this forum was for civil2011 (i have 2013) and it is no longer available.
Suppose you have an existing structure that you are going to tie into with a proposed pipe.
We label existing structures with smaller text and a different color (as opposed to proposed labels)
Is there any way to label the structure where the one single proposed pipe text is a larger text size with a different color, as shown here?