I cannot for the life of me get the start and end labels for any band to display within a profile view. Each band has the 'label start' and 'label end' labels ticked and the major/minor labels display at every other point but don't display anything at the start of the view or end. The profile views are taken from a simple straight alignment and the profiles themselves extend the full length of the view.
View 9 RepliesIs there a way to get the ProfileBandLabelGroup labels from a profile view. I see I can get the ProfileViewBandItems, but don't see a way to convert it into the labels. I'm looking to override the text components. The code below does that, it's just getting the object without having to have the user select it.
ProfileBandLabelGroup labels = ssResult.ObjectId.GetObject(OpenMode.ForWrite) as ProfileBandLabelGroup;
LabelStyleTextComponent textComponent = labels.GetAt(0).GetTextComponentIds()[0].GetObject(OpenMode.ForRead) as LabelStyleTextComponent;
Autodesk.Civil.DatabaseServices.LabelGroupSubEntity label = labels.GetAt(0);
label.SetTextComponentOverride(textComponent.ObjectId, "blue");
I am running CV3D 2011 on a Windows 7 64 bit workstation. I have a road profile that has a band which labels the existing and proposed profile elevations. For some reason the profile band labels (including the stations) randomly disappear and all you see is the band box. If you REgen they will reappear but will dissapear again when you plot preview and they WON"T plot...even though they are there in the drawing!
Civil 3D 2013 SP2 | Win 7 64-bit SP1
Intel Core i5-2500 @ 3.30GHz, 8GB Ram | ATI Radeon HD 5450
I was looking at placing pipe information into a Profile Band. I see that I can include the following properties in a pipe label in the profile band:
<[Total Slope Across Span(FP|P2|RN|AP|GC|UN|Sn|OF)]>
<[Number of Pipes in Span(GC|UN|Sn)]>
<[Drop Across Span(Um|P2|RN|AP|GC|UN|Sn|OF)]>
Only problem is they don't actually give me the information of a spanning pipe, only a single pipe. I see no way of choosing which pipes will be spanned. Am i missing something in the creation of the profile band that allows me to choose the spanning pipes or is this broken?
How to upload Civil 3d Sample profile with full band
View 1 Replies View RelatedI tried moving a Profile View and even though I selected everything at once and selected a base point and destination point, the Profile View Station and Elevation labels moved with a different offset than the Profile View itself. ?
Civil 3D 2012
i'm trying to get my data band flush with the bottom of my profile view. See attached screenshot.
Windows 7 x 64 bit
NVidia Quadro 2000 Dual Monitor
6.00 GB RAM
Intel Xeon W3550 @ 3.07 GHz
Civil 3D 2013 SP 2, Civil 3D 2012 SP2, Civil 3D 2011 V3, Civil 3D 2010 V3
The list of bands with location selected as 'bottom of profile view' is blank, where as 'top of profile view' displays the info correctly. With this error I can't select any of the band to add remove modify them.
I have attached 2 pdf's showing top and bottom views.
How to show the deflection anglesof alignments. I want to show those angles in band set or profile view.
AutoCAD Civil 3D 2012 SP 2
I'm trying to add assign a Pipe Network to a profile view Band in Civil 3D 2011. I was using COM to add profiles to bands because I couldn't figure out how to do it in .NET. But when it comes to pipe networks I don't see how you can do that with COM. How the .NET implementation is supposed to work? Here's the code I have that works for COM, except for the pipe networks. I essentially need to assign the correct pipe network to the band.
public static void AddProfileToBand(this ProfileView profileView, ObjectId profObjId, List<BandItemInfo> bandStyleInfosFromSet, ObjectId profileBandSetId){
using (Transaction tr = Application.DocumentManager.MdiActiveDocument.TransactionManager.StartTransaction())
[code]....
How to "NOT" label the top elevation in a profile view? (see attached pic)
I can live with the far right and left vertical labels if I could turn the top elevation off.
Civil3D 2014 SP1
Win 7 Professional - 64-bit
HP Z400
Xeon W3550 @ 3.07Ghz
24GB of RAM
Nvidia GeForce GTX 760
I click on my pipe in profile. Right click and add label. I see nothing, no label. All layers on and un-frozen.
View 6 Replies View RelatedI have a profile view created with several surfaces including a proposed surface. The stationing on the X-Axis of the profile view corresponds correctly with the PT's, PC's etc on the proposed surface profile, however the the labels that are actually on the profile line are giving me values such as PC: 0+668.62 when it should read 21+93.63.
I can't seem to find a correlation in the two numbers and am having difficulty changing the style to correctly reflect the stationing.
I've attached an image of a storm drain invert label for a storm drain profile. As you can see, the middle manhole has all three inflow pipes labeled. Is there a way to only label the inverts of the two pipes shown in the profile view?
C3D 2014
Windows 7 64-bit
In plan production, I have created the sheets (plan & profile) as a seperate drawing.
when I open the sheets, the pipe network profile labels are missing in model & paper space. (attachment 01)
I tried to on/off the annotation visibility tabs in the lower right corner (attachement 03)
Note: While creating the sheets, I select the tabs for pipe network & copy pipe network labels to destination drawings (attachment 02).
1. I had trouble with profile view of the alignment line shown. What step am i missing? Are there things that is turned off?
2. How can I best come up with the right volume to fill.
3. Do I need to learn the grading tools? or could i get buy with a section profile from the alignment. ( it is not even an alignment yet)
4. How to I render a rock fill in this cave-in.
The attached aerial image , has survey or cogo points that are imported to surface, to become surface points. . So I wanted to create a surface profile below and an outline of fill above it. Iideally the side profile would look like a trapezoid, where the base is the surface proile and top would be the design embankment.
But the reason , a surveying crew went down and took shots at the shoreline and a couple shots around the cave-in walls (higher elevation on the cave-in wall cannot be surveyed, although I coud have used a laser , did not) is so that a more accurate volume of the cave in can be obtained. I tried to label how far the road edge is from edge of the cave-in . Norice the higher elevations are the top edge around the cave in area.
The ouline for the embankment will be a mild slope then breaks to a more steep slope. like 4 :1 , then 1.5:1
where to change the text height and color for the lower band where the stations are. Also, how do I get the exist grade and proposed grade to show at the specified stations vertically like LDD used to do it.
Second, how do i mask the pipe in the manholes on the profile. Right now i can see the pipe inside the manhole. I clicked "enable masking" under the structure properties but no luck.
When I generate a band and the points that need to be labelled are very close to each other there is the possibility to stagger the labels (left, right, to both sides).
This works as I would expect it to.What I haven’t been able to determine is whether it is possible to adjust or influence the spacing between the staggered labels.
In the profile band the elevations are set to 3 decimal places. I just want to get it to 2 places.
View 3 Replies View RelatedAttached is a drawing with my profile along with elevations in the band.
UPPER BAND - has proposed road elevations on the left and existing road elevations on the right.
LOWER BAND - has pipe elevations on the left and the SAME existing road elevations on the right.
I've been messing around in the profile view properties but cannot hide the duplicate elevations in one of the bands.
In the Band Style_A pdf you can see the location of my elevation labels, they are below the bottom line of my profile view grid. In the Band Style_B pdf the labels are showing up in the proper location (above the bottom line of the profile view grid). To move the labels to the proper location I changed the "Gap" setting from 12.5 to -24. Is there a way to change this setting in my "style" rather than have to go make this change to the style every time I use it in a profile?
View 3 Replies View RelatedI did a grading, created surface with it and draw a profile view. Everything seems to be good, except with the vertical geometry band. I need to fix slope and length only at break point, means PI (blue line), but aligment has created more PI with each surface tringular line at intersection (us i note). Is there any why to specify PI only at a break points?
I can erase PI manually on static profile view mode, but i desire to do it in dynamic mode..., in case when conditions changes.
So I've got a collection of the LabelGroupSubEntity in the ProfileDataBandLabelGroup. I need to replace some values inside them based on what Vertical Geometry Point they are labeling. Is there an easy way to determine what station value it is labeling?
View 2 Replies View RelatedIs there a way to make the Profile band title a specific text style? At the moment it seems that when I access
Profile Properties>Pick Band Style>Profile Data Bans Style>Compose Label>Label style composer
I go to the Contents (under Text) and edit it to bring up the Text component Editor.
In this if I go to the Format Tab the text style is set to annotative, however under that it says font style as an overide. How do I remove the override and set the style of the text to the text style. And how do i change the text style.
How to add super elevation detail on Profile band.
View 1 Replies View RelatedI've been working with Civil 3D for a while and I've gotten the Profile View and Data Bands down.Whenever we create an alignment with only two vertices (at each endpoint) and make the Northings, Eastings, and Elevations show in the data bands, the start and end show no data. (As below) Now I'm sure the data band is set up correctly because if I add a vertex somewhere along the alignment, all the missing data shows up.
View 3 Replies View RelatedWe are using Civil 3D 2010, Version 4.1 and it is being used on both WinXP and Win7.
This is an issue that has been coming up at different times with profile views and them shifting when viewed from our viewports in our layout tab. It looks correct in the model space. But it shifts to the right 10' in the layout tab. We have 7 tabs in this drawing. I have looked through all of the profile view settings and it does not seem like any of these are the issue. I created a new viewport in the same tab and received the same shift to the right. I then created a new tab in the same drawing (not copied from the one that has the issue), created a new viewport, and the shift is not there. The PSLTSCALE, MSLTSCALE, and LTSCALE are all set to 1 in all of th tabs.
Woudl there be a layout tab setting that is causing this? This is happening on all of our machines with this drawing so I know it is not a specific user/machine issue. I have attached a .pdf showing the three cases described above if that were to provide any additional insight.
I want to change my elevations color to green and the other one to yelow. I can't not find this option. I using 3D 2011.
View 1 Replies View RelatedHow to set change the radius to degrees in horizontal geometry band set profile.
View 2 Replies View RelatedWhere the heck do I find the offset which controls the distance between the profile grid and my profile data band?
I have compared settings between ones that look the way I want and I'm just not seeing it.
(The attached doc shows you what I'm up to)
i have created a data band in profile view that should show a created profiles elevation, but some of the the data fields are missing irregulary. Also in the data band that shoud show the diferenece betven the tow profiles - EG and the new profile the data is missing. The EG profiles data and the surface are ok all is shown.
View 4 Replies View Related