How to calculate in a table the volume of cut and fill between the stations, The horizontal and vertical alignments are generated along with their sections. I’m wondering if there is a tool that summarize the volume of cut and fill between the stations in a table.
View 3 RepliesI use Civil 3D 2011 and I am new to it. I have created a natural ground surface from survey points. Now i want to create a finished surface with a specific slope in a specific direction at a specific elevation and then to calculate cut and fill volume.
I can create a flat surface at a specific elevation. How to tilt this surface to a specific slope along a specific direction.
I have a problem when calculating the volume of a design plan, the slope of the land, the design had to be made so as not to slide trap. How it makes grading a trap,
View 2 Replies View RelatedIs there a way to create a table of stations and offsets along a specific alignment at chosen locations?
Dynamic would be preferred.
I'm currently using version 2013.
Windows 7-64
8GB RAM
AutoCAD Civil 3D 2013
At my job site, they is about 20meter height of uneven rock surface in the excavation pit.
To calculate the volume ,I need to include this uneven rock surface wall.
For doing so,The sharp edge will displays in the cross section.
Because the uneven surface, I cannot create the surface with normal step.The TIn line will joins horizontally,not in vertical direction as is intended.
AutoCAD Civil3D 2014
Inter(R)Core(TM) i7-3770 cpu@3.40GHZ
RAM 8.00GB
64-Bit window7
QuadroK6000
I am using C3D 2012 and i know how to create a table showing volumes for different elevation ranges with different colours, but how to show the total cut or fill for the volume surface in the same table so that you dont have to manually add up all of the cuts or fills? or have to display only two ranges?
View 1 Replies View RelatedI have an existing survey surface, and I want to know how much cubic yard of materials to fill up from the bottom to elevation 876. See attached image for detail. Here is what i am going to do....
- i will create a surface of the fill area (from bottom cotours up to el 876) then do a volume surface bwt existing ground surface and the new fill area surface to get the volume of it? Is this a right way to do?
How to calculate the AREA of cut and fill analogous to the volume of cut and fill between surfaces, but instead only between the alignment and the road profile in the prolfile view. From what I've read of similar posts a few people have had the same question but have been instructed how to do it with volumes as opposed to area. Also how to insert a table of cut and fill area analogous to the one you can inset from the volumes dashboard.
View 5 Replies View RelatedAttached are two files: 1 file has 0 values on the volume table, and the other file has Sample line group Properties.
Surface 3 is the surface that has the existing actual survey points . Do I have to pick another surface : the other two are the surfaces I created in the Corridor as surface boundaries , Top and Datum
How to get the Volume Elevation Table masking to work?
I can only get the Title to work correctly - everything else plots as a black blob if Fill is on. With Fill off - there is no mask.
I have just created a Total Volume Table and everything is perfect in Model, but when y change to layout, the table is miising. I can barely see the title of the table zooming, but anything else. The tables are still there, but so tiny and with just the title, there is no data!
View 1 Replies View Related about a Volume Table style, where I have correctly showing in Model Space and is "Split" in the Table Properties. This is a "Total Volume Table" and is Dynamic.
Just Fine in Model Space... yet is showing within a Viewport (typ. plan sheet) that each Split is simply Staked ontop of each other ?
Thought I (we) came across this a few years ago... yet no issues latetly till now, and also mainly first time I've likely split the Table in R2012 (currently used).
Have maintaining View Orientation "true", yet still nothing.....
Xi Computer (Win7 64bit O.S.)
i7 3770K @ 4.5GHz Sealed Water Cooler
Quad Core w/ Asus P8Z77-V LE mobo
16GB DDR3 @ 1600Mhz RAM
15K Seagate SCSI H.D.
Nvidia Quadro 2000 (span2) + FX4600 (3)
ViewSonic VS2436 series displays (3)
I need write Cut and Fill Labels on Volume surface in each 10x10 meters. Civil 3D can write Spot Levels on grid, but I need write Cut
and Fill values in grid area. Using Surface >Utilities>Bounded volumes I can get the values on selected closed polygon, but write to all is very long work. How to do write Cut and Fill labels on grid.
I want to show Cut & Fill volume in Different Hatch patterns (Excluding Solid Hatch).
View 3 Replies View RelatedI have created surfaces for my original ground and my corridor. Both have appropriate boundaryies and the TIN looks good for both. I am trying to create a volume report through Volume Dashboard. I am able to create the volume surface with no issues but the numbers it comes up with do not seem correct. I can see from my profile that there is a small fill but the software seems to create a fill that is almost half of all the material when my profile shows there is more cut.
I tried creating a sample line group...it also shows the majority is cut. The only thing I can think is that there are about a dozen areas where my daylight does not work. how to do this volume correctly?
Civil 3d project. My familiary with actual road construction is quite basic.
I'm at the stage where good Civil 3d practices need to be employed when generating volumes. Attach are two files showing a road section with links and layers & also, the profile.
1. Like to turn off the links first of all and show labels instead.
2. How does the total depth of the gravel road (0.3' for gravel, 0.5' for aggregate base) factor in the profile view? What shown is the EG(in green) and FG,the top of the gravel road.
3. The cross section view: Three surfaces were used, the top of the gravel, the bottom of the base and the Existing ground, Is this correct?
4. Is there two sets of Volumes? 1. Cut and Fill areas, 2. Pavement structure: Volume of the gravel and volume of the aggregate base.
5.Refer to 4. So the Cut and Fill areas need to be done first, then the pavement structure, correct. ?
I'm to compare volumes in c3d to Inroads. My volumes are not matching ( cut and fill are not even close). Civil 3D uses the average end area and InRoads uses 'triangle method' to calculate the total volume. How can I get C3D volumes to match InRoads which is verified correct?
View 5 Replies View Related(I'm using Civil 3D 2011)
I have a corridor with an associated sample line group, and I have produced some material volume tables to give me quantities for my corridor structures and cut/fill volumes. When I look at the material volume tables they are at a seemingly arbitrary stationing. The sample line group which the material volume tables are (supposedly) based on are on alignment L1000 and they run from station 1133+73 to station 1154+00 every 10 meters. The material volume tables show volumes broken down by stations starting at station 3719+58.66 and runs through to station 3786+08.92. It is sampling at a seemingly arbitrary frequency, there is absolutely no alignment in my drawing that has stations remotely resembling those numbers, and there is definitely no sample line group it could be using that samples an alignment or stationing anything like that shown in the materials volume tables. Here is a quick screenshot of what my material volumes tables look like:[URL]
I am working on a large park project. I have a proposed and existing surface. I have created a volume surface to show elevation banding with cut and fill ranges. I need to create a drawing for someone who doesn't have civil 3d showing all the "cut" areas. They really want a boundary of hatch. What is the best way to do this after I change my analysis to -30 feet cut to 0 feet cut.
View 9 Replies View Relatedcalculate the volume.I attached here my dwg file. I never done this before and I want to know the correct answer when I want my land to be levelled at 6m.How much volume to fill and the land to be removed.
View 9 Replies View RelatedThere are points in different levels i wanna make the surfer with this points and project the surfer on the down surfer(that makes with other points) after that make an enclosed Volume and finally Calculate the Volume between this 2 surfer. How its possible to Calculate?
View 8 Replies View RelatedI am trying to calculate muck away for work, and I have drawn the site plan in millimetres for accuracy. However when I try to calculate the volume I get this value: 3.6293E+12. I am guessing that it is saying this due to the fact its in millimetres, and I am trying to calculate a large area and convert in into metres squared. What this value means?
View 1 Replies View RelatedHow do I generate a table that shows cut and fill quantities for comparing two surfaces similar to that what shows up in the panorama window. I am not working on a road project with an alignment.
View 1 Replies View RelatedIs it possible to calculate the volume in this elbow for liquid?
View 1 Replies View RelatedI'm trying to work out a way to calculate the fill volume difference for a proposed landscaping plan (images attached) and how to model and calculate the amount of fill required to do the job.
Site-Plans-4-Recovered.jpgSite-Plans-4-Recovered2.jpg
I'm trying to attach a daylight subassembly that follows my DOT chart below. Is there one that does all of this or do I need to use a condtionalcutorfill and "something else" to do it? If the case, what subassembly would I use for the "something else"? If it's cut, the table below also determines the backslope... forming a ditch. How is the clear zone factored in? I need it to go the the flowline of the ditch when it's in cut. I have a design speed of 40mph, ADT of 7000+.
View 1 Replies View RelatedWith command massprop I can get many interesting data about 3d object, but where can I set material that my object is made of. Lets say I need to calculate volume and mass of my object which is made of aluminium, what are my options?
View 3 Replies View RelatedI have created Table styles for Structures in Autocad 2009 Civil 3D, but now I have Autocad Civil 3D 2011 and the Table Style Fill appears black in paper space.
View 2 Replies View RelatedI have a set of 8 coordinates that outline a pit. I have been asked to calculate it's volume. I have input the coordinates, and have produced a 3D image of the pit. I was hoping to be able to convert the object (the pit) that I have created to a solid, so I could then determine the volume, although it is proving to be difficult.
how I could calculate the volume of this pit?
Having a surface, and then applying a building pad, how can i discover the volume of excavation?
View 1 Replies View RelatedHow to calculate Column quantity and gross volume.
View 8 Replies View Related