AutoCAD Civil 3D :: FDO Connect To SID

Nov 21, 2013

I've started connecting to Raster (.sid) Aerials thru mapwspace rather than inserting them thru the Planning and Analysis Workstation due to greater control with gray scale and resampling raster and such.  I started noticing after I save, I can't select anything in my drawing.  I was connected to a whole county Aerial .sid file, so i thought maybe if I only connect to individual tiles for my project area which consisted of 9 .sid files, the issue would go away.  It didn't.  I tried typing REA, purge, audit, then eventually I would crash.

Is there something wrong with FDO connections with .sid files thru mapwspace in C3D 2013???

View 1 Replies


AutoCAD Civil 3D :: How To Connect Assemblies

May 3, 2013

I'm trying to construct a complex corridor of urban highway. To simplify corridor i've made assemblies for each side of the road (see picture). This solves problem of countless number of regions (and assemblies) that I'll need to set if assemblies are for whole profile.

The problem with seperate assemblies for each side of the road is that I cannot connect them using Median subassembly because Marked point and Median are in different assemblies. 

View 3 Replies View Related

AutoCAD Civil 3D :: How To Connect The Surfaces

Nov 2, 2013

When you paste a surface into another how does it connect the surfaces?  Does it create a vertical wall where at the edge of the paste surface?  Can you tell it to grade a certain slope to the surface you are pasting into?

View 1 Replies View Related

AutoCAD Civil 3D :: Connect To Raster Data

Jul 22, 2008

Trying to connect to raster data through FDO Provider , 3D Map for Geospatial, raster formats are Drg, MrSid, Tiff and ECW, all formats load up but do not display, using Autocad Civil 3D 2008.

View 9 Replies View Related

AutoCAD Civil 3D :: Connect Volume Tables

Aug 25, 2012

I have 4 corridors on same alignments (pics1). I created materials for each corridors (pic2). Then I created multiple section view for each corridor (pic3) ( for all corridors in section view table tab, i added corridors own materials). but cumulative material volume reset to zero at each new corridors beginning. In my project, corridors cumulative material volume value should continue from the previous corridor's value. Can i connect this volume tables or can i merge corridors ?

View 6 Replies View Related

AutoCAD Civil 3D :: Map Connect Link To Geo Tiff

Jun 6, 2013

I am using the map connect command to import a geotiff file to NAD83 coordinates.  After import, the image displays correctly at the correct location, however my xref manager indicates that the image file location is in my local app folder within the C drive on my computer even though I specified the target base file on our network server.   I also noticed the map connect function converts the files to a png file.  

Because the image link resides on my computer others cannot view the image when they open the drawing.  I don't fully understand how the map connect function works, do I need to use the map insert command if I want the image to be hard linked into the drawing?

View 3 Replies View Related

AutoCAD Civil 3D :: Connect To DWG Database Via Com Interop

Mar 23, 2012

C3D 2012 SP1

I am trying to connect to a dwg database via com interop. Here is the
using System;using System.Diagnostics;using System.IO;using System.Windows.Forms;using Autodesk.AutoCAD.ApplicationServices;using Autodesk.AutoCAD.DatabaseServices;using Autodesk.AutoCAD.Runtime;using Autodesk.AutoCAD.EditorInput;using Autodesk.AutoCAD.Interop;using Autodesk.AECC.Interop.UiLand;namespace Proj2{

View 4 Replies View Related

AutoCAD Civil 3D :: How To Connect Subassembly To Point 2

Apr 20, 2013

I created one section with two assemblies. Main line assembly and offset (second line) assembly. Each assembly has its own alignment and profile.In strait its all ok, but in curve I get strange situation, that I try to solve. (look to the picture)

I add Mark points on Point 1 and 3. Then connect them using Link Slopes Between Points. Knowing that Point 2 is not static, but moving point I can't find any way to connect subassembly edge point to that Point 2.

So how can I connect subassembly to Point 2? Or maybe there is a smarter way to connect points 1 and 3. Slope from 1 to 2 should be 50:1 and from 2 to 3 should be 1.5:1

View 5 Replies View Related

AutoCAD Civil 3D :: How To Connect Point And Link

May 15, 2013

my problem is i want to connect shoulder point and the daylight link with the same slope as my is much more clear in the attached photo.

Civil 3D 2014 x64
Windows 7 64-bit

View 5 Replies View Related

AutoCAD Civil 3D :: MAP Connect To Map Info (using 2013)

Oct 3, 2012

We use map info as our native GIS and can use these .TAB files with MAPIMPORT in C3D, but what I would really like to do is use MAPCONNECT like can be done for .SHP files, etc.. I've inquired with [URL].....and they have confirmed that their FME product doesn't support 2013.

View 8 Replies View Related

AutoCAD Civil 3D :: Data Connect And Transformation Settings

Jul 29, 2013

I have geotif images that I've purchased from Washoe County GIS. They have world files that work great with data connect. That is, as long as I want to work at sea level. We have a Combined Factor mandated by the County for all record maps. it's a simple grid to ground factor. I can set this factor in the drawing settings and import my sea-level coordinate files just fine. The pboblem is that I can't get the Data Connect to work with the transform settings.The problem is the same with Geotif files and SHP files. I've tried using an x-reference drawing to insert the Geotif and then scale up the geotif but the imagery doesn't scale up.

Is it a program bug that keeps Data Connect from recognizing the transformation settings?

View 7 Replies View Related

AutoCAD Civil 3D :: Pipe Networks - Connect To Part

Jun 5, 2013

I have a 18' x 10' special structure where I'd like to be able to connect the pipes as shown to the structure but I'm not aware of any way to force the Connection point of the pipe to the desired location along the structure.

Normal behavior is to connect all pipes to the same insertion point or center of to go about maintaining pipe connection orientation to reflect the design requirements?

View 9 Replies View Related

AutoCAD Civil 3D :: Insert SID File Using Data Connect

Jul 26, 2013

I am trying to insert an Mr Sid file using Data Connect. I am running 2011 C3D. When I try adding the file to the dwg, it tries to execute the query, but then I get an error "There was a problem adding data to map."

The folder containing the SID file has two other files...the .sdw file and the metadata file. Is there another file missing? Or is the SID file too's 1.6GB.

View 3 Replies View Related

AutoCAD Civil 3D :: How To Connect Two Points Via Surface / Subassembly Composer

Apr 22, 2013

I'm trying to create flexible model of a penstock with different ground surface elevation scenario.

In case if both top points of trench below or above EG, there will be cut/fill case to EG.

how to connect P1'/P2' and AX1/AX2 via EG? Basic link wouldn't work because it will be just a straight line.

View 5 Replies View Related

AutoCAD Civil 3D :: Pipe In Same Network Won't Connect To Structure In Plan

Jan 8, 2014

I'm working in Civil 2012 and I'm putting in existing SD. I put in 2 DI's and a MH all on the same network (there is only one in my drawing) and I go to put in pipes and I click to connect to the first DI and then I'm kicked out of the command. What do I do?

View 2 Replies View Related

AutoCAD Civil 3D :: Leader Vertex Does Not Connect To Line When Changing Scales

Nov 15, 2012

I’ve had this problem with my proposed elevations for quite some time so I finally want to fix it while I’m a little slow. The problem I have is when I change scales, my elevation’s (in dragged state) leader vertex does not connect to my line. I’ve attached my lable styles...

View 7 Replies View Related

AutoCAD Civil 3D :: Can't Turn Transparency Of Raster Images Off When Using Data Connect

Jul 23, 2012

I have a set of four images I am referencing into a drawing through the data connect feature found in Planning and analysis that overlap. I am running Civil 3D 2013. I would like to be able to clip the images as well as turn off the transparency but I can't seem to figure out how. If you select the images cadd thinks it is an image referenced outside of Data connect, but the clipping tool doesn't work, and it doesn't even matter if you de-select print transparency in the page setup, it still prints transparent. Is there another set of commands or tools that I am not aware of that allows you to edit an image brought in through the data connect?

View 2 Replies View Related

AutoCAD Civil 3D :: Create A Smooth Surface That Doesn't Connect To Anything Overlapping It?

Mar 22, 2012

I'm creating a 3d ramp and need to create one surface of the whole thing, but as its overlapping on certain areas the surface keeps attaching itself to the corridor below it and another corridor crossing over top.

how to create a smooth surface that doesnt connect to anything overlapping it?

View 2 Replies View Related

AutoCAD Civil 3D :: Connect The Lowest Points Of Series Of Cross Sections?

May 15, 2013

is there a way to connect the lowest points of each cross section, for a series of cross sections, and possibly make a pline or feature line in plan view?

Civil 3D 2013 SP1, Win 7-64 bit

View 9 Replies View Related

AutoCAD Civil 3D :: SHP File Data Connect Imports To Wrong Coordinate System

Jul 11, 2013

When the attached shape file (change soilmu_a_a.txt to .shp) is imported using MAPIMPORT the data aligns with other imported georeferenced raster imagery (said imagery was imported using the MAPIINSERT command).  If the same shape file is imported using the data connect tool it shows up in a much different location (see word document).

The drawing coordinate system code is "UTM83-18F" and the data was downloaded from the Web Soil Survey's data download with the identical coordinate system (see attached readme.txt).

I prefer to use the data connect option when importing this type of shape file because I can label them all using a theme and use stylize the data for visualization/presentation.

As an aside, I have found that data connect does not automatically transform data coordinate systems to match your drawing coordinate system as advertised.  I've used the edit coordinate system to no avail; however, again when the file is imported using MAPIMPORT and saved as a drawing (with native data coordinate system) and then that drawing is queried from a drawing in a different coordinate system it seems to transform the coordinate system just fine.  Is this a problem with data connect?

View 7 Replies View Related

Corel CONNECT X5 :: Connect Search Doesn't Recognize Keywords In CDR Files

Feb 15, 2012

i have been a long user of romcat... but would like to use the new corel connect. i use the folders selected to my HD folder that has all my cdr files (20yrs worth from ver 1). when i type in a search word that is in 100's of my cdr files keywords... connect doesnt display them. In romcat it does display them, even older files, with the same key word. connect only shows cdr files that have in its file name part of the search word, but seems to ignore the key words in the files.

I have all my job files with important key words within them, but the actual file names are simple job numbered names. i noticed on searches from X5 content on dvd, the files also are just numbers, but the search finds key words.

View 2 Replies View Related

AutoCAD Civil 3D :: Data Panel Is Missing / Data Connect Route Doesn't Work

May 3, 2013

I've just installed Civil3D, 64-bit on windows 7(running on bootcamp) and am trying to insert a georeferenced raster image but have encountered some issues. 

1. "Home tab>>Data panel>>>insert An Image" - The data panel is missing and it's also not found in "customize palettes" 

2. Trying the data connect route does not work either: Display manager>>>Data>>>Connect To Data - There is no 'Data' option and I cannot connect to Data.

View 1 Replies View Related

AutoCAD Map 3D :: Connect JP2 Via FDO

Mar 7, 2012

I can connect to jp2 aerials via FDO but the images do not come in. They work fine with raster insert, why not FDO?

View 3 Replies View Related

AutoCad :: How To Connect 4 And 5 Buttons

Dec 16, 2011

I use hp 5 buttons optical comfort mouse, windows 7 and autocad 2012. I do not know how to connect 4 and 5 buttons with autocad. i have already tried customize user interface with no success.

View 4 Replies View Related

AutoCad :: How To Use DB Connect With Oracle

Nov 30, 2011

I have a new requirement from company to save a static drawing's dimensions' data into DB table. We have hundreds of drawings. DBConnect connects with oracle using ODBC. But how it is possible that we draw a drawing and its attributes are saved in DB.

View 3 Replies View Related

AutoCAD Inventor :: How To Connect Pipe To TEE

Jul 12, 2013

Look at the picture i attached

Pic 1 = i create a simple route for piping with branch
Pic 2 = after i create that route and click on populate Route i got this model
Pic 3 = when i go closer and zoom on the fitting i have this model

View 5 Replies View Related

AutoCAD Map 3D :: DWG Insert That Contains Data Connect

May 15, 2013

I have tried the XREF route to look to another drawing to bring in my NED files instead of putting my NEDS with my shapes and point data.  The drawing that contains the NEDS were brought in using data connect.  When I xref the NED drawing into a new drawing, nothing shows up.  Zoom Extents does not show anything nor does anything appear to be turned off.   When I do the xref, I see the image of the tiled NEDS and click on use georeferenced location (because I am trying to trick the neds to stay together but translate together).  Is there a better way or what could I be missing to get it to show. 

Autodesk 2014 Infrastructure Design Suite - Premium
Windows 7 Professional, x64

View 9 Replies View Related

AutoCad :: Get The Line To Connect With Circle?

May 24, 2012

I have a little problem with trim in autocad 2012. After trimming some lines that cut through a circle there's a big gap between the circle and line, so there's no way i can create a polyline. How do I fix it?

here is the figure w/o trimming


Here it is after trimming


And as you can see there is space between the lines. How can I get the line to connect to the circle?

pic 3.png

View 4 Replies View Related

AutoCAD Map 3D :: Openstreetmap / Unable To Connect Via FDO

May 24, 2013

i'm trying to add a WMS connection to theOpenstreetMap service, but i receive error message "impossibile connect"

I tried several link adresses, but the results still remain the same. I don't use proxy servers.

View 1 Replies View Related

AutoCAD Map 3D :: 2013 Connect To Arch GIS GDB 10.0?

Jul 6, 2013

I am using AutoCAD MAP 3D 2013 32 bit version. In this, I can find connection with Arch GDB. But when I am going to connect it shows the error and the provided conection is for Arch GIS 9.3 only.

How can I get FDO for ArchGIS 10.0

View 2 Replies View Related

AutoCAD Map 3D :: Connect To SQL Server 2008 R2 By 2012?

May 11, 2011

How to connect to SQL Server 2008 r2 by using Map 3D 2012? I can't to make it. It prompts the message "Invalid connection". I used the IP as the service name of map 3d.

View 9 Replies View Related

Copyrights 2005-15, All rights reserved