I am using AutoCAD MAP 3D 2013 32 bit version. In this, I can find connection with Arch GDB. But when I am going to connect it shows the error and the provided conection is for Arch GIS 9.3 only.
How can I get FDO for ArchGIS 10.0
We recently updated all of our software at my company from 2010 architectural desktop to 2013 autocad. We do a lot of architectural work where we use the "wall" functions to draw our floorplans. I have noticed that the walls are disappearing on some files and not on others. Or we will only be able to see the outside line of the wall, but not the interior, which results in an undesirable appearance to the floorplans.
I have also run across these error messages when opening the files, I dont know if they are related or not:
"Unhandled exception C0000005 (access violation reading 0xffffffff) at address E43AA180h"
and
"Unhandled exception C0000005 (access violation reading 0xffffffff) at address D41218AEh"
How to represent a bottomless arch (arch span)? I can make a horizontal arch pipe, but I only need the top half. I also thought about building a corridor.
We do have a storm drain system running perpendicular above it and need to show the arch as a crossing. Corridor would work but I think I would prefer a pipe network-type solution.
Is it possible to obtain Architectural unit dimensioning (ft and inches) in a metric drawing ?
View 3 Replies View RelatedWe use map info as our native GIS and can use these .TAB files with MAPIMPORT in C3D, but what I would really like to do is use MAPCONNECT like can be done for .SHP files, etc.. I've inquired with [URL].....and they have confirmed that their FME product doesn't support 2013.
View 8 Replies View RelatedDirect connect is broken in maya 2014 osx. This now means that dwg, dxf and iges will not import. I have the latest Service pack 1 installed but still no go! This means the only work flow is to do it on a windows version of maya then open it in the Mac.
View 2 Replies View RelatedI am working on a flood inundation, I would like to find a lisp or command(i'm not finding) to connect two points with a given elevation following the surface file or surface entities.
here is a small section as example right now it's just guesswork, some of these have taken a week to connect all the sections.
i have been a long user of romcat... but would like to use the new corel connect. i use the folders selected to my HD folder that has all my cdr files (20yrs worth from ver 1). when i type in a search word that is in 100's of my cdr files keywords... connect doesnt display them. In romcat it does display them, even older files, with the same key word. connect only shows cdr files that have in its file name part of the search word, but seems to ignore the key words in the files.
I have all my job files with important key words within them, but the actual file names are simple job numbered names. i noticed on searches from X5 content on dvd, the files also are just numbers, but the search finds key words.
How do i change my scale to arch?
View 5 Replies View RelatedWhat actually is the difference between the standard sheet eg ARCH D (36x24) and ARCH Expand D (36x24) sheet sizes? this have to do with printable margin areas?
View 3 Replies View RelatedI have dwg drawing sent to me with archstyle font or text. The archstyle is missing on my text format autocad 2012. How to downoad or import archstyle to my autocad 2012
View 1 Replies View RelatedI was given an arch length dimension and need to figure out the radius of the arch. I know the depth of the arch but not the width.
Is there a formula for figuring out the radius of an arch with a determined depth?
See attached pdf
I have a lisp program that creates a arch leader with a arrowhead on the end. All of a sudden the arrowhead does not appear on the end of the leader but out on space. Not sure what this is happening.
View 1 Replies View RelatedI'm having an issue where AutoCad Architecture 2011 is crashing on some but not all machines (4 total) when a file is closed.
We are also getting what appears to be random slow downs on files when opening and a jumpy mouse that makes drawing impossible. I have not been able to establish a pattern to point at specific files to being the problem as it happens across several the are fine one day, not fine the next and fine again a day later. All stations are identical.
Win 7 Pro - 64 bit
Intel Xeon cpu 3.60Ghz (2 processors)
9 BG RAM
NVIDIA GeForce GT 240
I need to put a 42 x 29 Arch Pipe in my drawing. I found a 44 x 27 in the elliptical arch catalog. But I can't get it to let me create one that's 42 x 29.
And I'm also having trouble making a label for it. This is one of three culvert pipes in this network. The other two are round 36" CMP. The label for those says XX' of 36" POLY-COATED CMP @ x.xx%. Once I need the label for this third pipe to show as XX' of 42" x 29" ARCH PIPE @ x.xx%.
When I tried to make the label style, I saw "Pipe Inner Diameter or Width". But I didn't see one for height.
I have some foreign drawings the block definition of "_ArchTick" has been changed to get a thicker tick in drawing's dimension. When I have new dimestyle and copy paste into the foreign drawings, it always use the drawing's block setting of "_ArchTick".
How I can paste a new dimstyle and bring in the block of "_ArchTick" to overwrite the one in current drawing?
I had thought this would work with no problem. I know the elevation I need to start an arc at and an elevation at a point along the arc. I drew that portion of the arc and then extended the arc to a line where I need the arc to end. I had expected the arc to extend along it's current grade the way a straight Feature line would. But the end dropped to 0.
I undid the extension, listed the FL arc to get the grade, extended it again and used the Elevation Editor to set the previous grade. But why didn't the extension work? I checked for other FL in the site that might cause this but there were none.
When I am in page setup manager and want to use the "Adobe PDF" plotter device, I can't set a paper size other than the standard one like letter, legal, 11x17 ect. I need to have the "Adope PDF" plotter to print a Arch D size paper but that selection dosent even show up.
I have troubleshooted all the usual supects, of going to properties next to the printer selection bringing me to the plotter configeration page, where in the device and documents tab I then proceed to the custom properties selection, where the adobe document properties page comes up and under the adobe pdf setting tab...I still cant change or find the Arch D 24x36 paper size under the adobe pdf paper size selection tab other than the standard seletions.
Among about a dozen ACAD users in my office, one is missing the "Arch D (landscape)" paper size that accompanies the PC3 file we generally use. I have checked that the roll size and other settings in the machine in question and all of that looks good. I don't want to edit this PC3 as it works for everyone else and don't want to create a new PC3 for this one user.
View 2 Replies View RelatedThis happens every time I save as to dwg, it's very annoying.
View 3 Replies View RelatedHow do i arc some text, without going to the warp settings because thats too hard to work with, i need it to arc like aroudn a circle.
View 4 Replies View Relateda way (or filter) that will arch and image (say 9" wide x 4" high) like you can do with the arch type effect? The top and bottom would arch and the sides would flare out. The 3D distort filter doesn't do the trick without major playing and tweaking.
View 2 Replies View RelatedI need to construct an arch in revit but Ive only been able to make a curved beam in the wrong plane. Whats the best way to make an arch so that it would look like a straight beam in plan view?
It needs to connect to ground level in two places and have a specific height if thats relevant.
I want to make slightly curved arch blur effect, but I can't figure it out how to.
Using radial blur, it needs huge canvas size so I don't want to take that.
Also I want to control arch angle manually.
How can I create such easy text arches?
View 1 Replies View RelatedHow do I arch text without any distortion? I'm trying to wrap text around a logo.
View 1 Replies View RelatedSo I've started to work on materials and lighting and a lot of tutorials show using the arch & design templates. problem is that i don't have any templates listed. the list is completely empty. Can i install these, or fix this? If its just a file missing, I'm not sure which it would be or where it would be at.
Max 2011 SP3.
I used BRUSHED STEEL, in Arch & Design, now I have to change the color of this material, from grey brushed steel into yellow/gold brushed steel!
Can this be done?
How to make an arch shaped door i have a box with a hole cut out i have create another two boxes for the left and right part of the door (joints) and attached them together then bridge them together. here is the problem i am working with a maya tutorial and on the bridge you can set the number of divisions but in max you cannot set the number of divisions.
Computer engineer, 3ds max freelancer
3ds max used currantly using max 9 (7, 8)
poser using 8 (5,6,7)
windows xp sp2
512 memory
40 and 80 gb hard drives
sis mirage 3 VGA Card
Asus motherboard
How to create the arch part of the dials, at least I think it would be an arch. With the top photo, the "arch" has 2 colors so I would need to have 2 layers, one holding one color and one holding the other color, but how to make them and I had no success with the "arc" tool.
In the second photo, it's very difficult to tell, but the left side of the arch is green and the right is a pale yellow so again, I think I would need two archs. The second photo also these tick marks that are at the top of the arch and again, how to recreate them.
I am using some A&D MR metal material in my scene and it is coming out transparent. The same is happening for any material that has a shine/reflection. It looks like a poor quality 'cloaking device' type effect.
I am rendering with Mental Ray using a bitmap environment background, daylight system and MR photographic exposure.
System information: Win7 x64 / 3DSMax Design 2014 SP3 / AutoCad 2014 SP1 Lenovo E30 ThinkStation Xeon E31225 Quadcore @3.10Ghz PNY GTX760 XLR8 2GB (334.89 Driver) 24Gb Ram Corsair 650w PSU
