AutoCAD Civil 3D :: How To Connect Subassembly To Point 2

Apr 20, 2013

I created one section with two assemblies. Main line assembly and offset (second line) assembly. Each assembly has its own alignment and profile.In strait its all ok, but in curve I get strange situation, that I try to solve. (look to the picture)

I add Mark points on Point 1 and 3. Then connect them using Link Slopes Between Points. Knowing that Point 2 is not static, but moving point I can't find any way to connect subassembly edge point to that Point 2.

So how can I connect subassembly to Point 2? Or maybe there is a smarter way to connect points 1 and 3. Slope from 1 to 2 should be 50:1 and from 2 to 3 should be 1.5:1

View 5 Replies


AutoCAD Civil 3D :: How To Connect Two Points Via Surface / Subassembly Composer

Apr 22, 2013

I'm trying to create flexible model of a penstock with different ground surface elevation scenario.

In case if both top points of trench below or above EG, there will be cut/fill case to EG.

how to connect P1'/P2' and AX1/AX2 via EG? Basic link wouldn't work because it will be just a straight line.

View 5 Replies View Related

AutoCAD Civil 3D :: Subassembly Composer - Point Codes And How They Are Used

Nov 5, 2012

I need to make them my best friend because the Subassembly Composer is basically useless unless you use the proper point coding for your SAs. This I know... I've attached an image from the Autodesk file that shows multiple point codes per link and point for the DaylightStandard Civil 3D Stock SA.

Which point codes must I use in my subassemblies to ensure I can create corridor surfaces properly down the road? For example the DaylightStandard SA shows...

P3 shows: Ditch_Out, Hinge, Hinge_Cut
P3 also shows: Daylight, Daylight_Fill 
P4 = Dayltight, Daylight_Cut

If I'm building something similar in the Subassembly Composer what the heck do I focus in on for my point code. I will have issues with my Corridor surfaces down the road if I don't do this properly up front. I've seen examples where the Input / Output Parameters you define a string for the coding, is this to apply multiple codes to a point or a link?

View 1 Replies View Related

AutoCAD Civil 3D :: How To Connect Point And Link

May 15, 2013

my problem is i want to connect shoulder point and the daylight link with the same slope as my is much more clear in the attached photo.

Civil 3D 2014 x64
Windows 7 64-bit

View 5 Replies View Related

AutoCAD Civil 3D :: Corridor Surface Not Using Correct Subassembly Point

Apr 29, 2013

I have created a new assembly that uses a HMA dike rather than your typical curb but my surface always begins at the top of the HMA pavement rather than the top of the curb subassembly. See Picture. Where's the setting to fix this (is it a daylight setting) or it is a bigger problem in that I didn't create the subassembly or assembly correct to begin with?

Win7 (x64), EVGA 790i, 8GB RAM, EVGA 8800GT, 250 GB iSSHDD, & RAID 0/1

View 5 Replies View Related

AutoCAD Civil 3D :: Conditional Point / Link Code In Subassembly Composer

Jan 10, 2013

it is possible to define point/link codes using some conditional expressions. When I try to write in an expression under "Link Codes" I get an error. Is there a way to create conditional codes without the use of "decisions"?

View 1 Replies View Related

AutoCAD Civil 3D :: Import Subassembly API For Custom Subassembly - Error?

Nov 12, 2013

When I use ImportSubassembly API to import my subassembly created by Autodesk Subassembly Composer  into my civil project, it reports error-"eFilerError".

the code like this:

atcFile = @"D:9f92eaa4ef514ac982518852e1169932.atc";
itemId = "ab660722-c69d-4ade-b373-0e9f99c94e55";
SubassemblyCollection subassemblyCollection = cDoc.SubassemblyCollection;
ObjectId subassemblyId = subassemblyCollection.ImportSubassembly("TestSubassembly", atcFile, itemId, this.doc.Editor.GetPoint("Select import subAssembly location").Value);

However, it is OK if to import subassembly provided by Cilvil 3D.

View 9 Replies View Related

AutoCAD Civil 3D :: How To Get Channel Subassembly To Attach Assembly Insertion Point At Channel Flowline Marker

Sep 26, 2012

How can I get the channel subassembly to attach to the assembly insertion point at the channel flowline marker?  I need the flowline to follow my profile elevations.

View 4 Replies View Related

AutoCAD Inventor :: How To Copy Subassembly To Create Similar But Different Subassembly

Sep 27, 2013

(in Inventor Pro 2014,64 bit):

I've made an stairs assembly that contains adaptive parts that are all controlled by the assembly parameters.

Here is my assembly and the controlling parameters. The stringers on the side are made with the frame generator and use the "extend" feature to get the appropriate length, as driven by the parameters. The reason I used frame generator is so that I can easily change sizes of the stringers down the road, if needed.  I chose to make the parts associative so I could control all of the parameters from within the assembly instead of opening each part separately.

My goal now is to be able to use this assembly (or something similar) as a template to create new sets of stairs, all to be placed in the same main assembly.

I attempted to duplicate all of the parts (append a "2" at the end of each file name and replace components in the new set of stairs with the 2nd version) but ran into problems with the two stringers. I can't figure out what to do to get the Frame00001 and Skeleton00001 to reassociate to Frame00002 and Skeleton00002. So any time I change my slope, the original stairs will end up trying to copy the new stringers instead of keeping the old ones.

how can I make this assembly reference a new frame, and secondly?

View 2 Replies View Related

AutoCAD Civil 3D :: How To Create Subassembly

Jul 24, 2013

How can I create a subassembly..AND hot to add a Pave 3 option or another subbase depth. 

View 9 Replies View Related

AutoCAD Civil 3D :: Add Subassembly To Corridor?

Nov 18, 2013

We are trying to edit a small portion of an existing corridor by adding a generic daylighting subassembly.  The add subassembly tool in the Corridor Section editor works, but we get an error because the new sub doesn't have a target surface specified.  how to add a target for a sub that is added after the corridor was created?

Civil 3D 2012 & 2013 & 2014
Toshiba Qosmio X505-Q890
2 x i7 - Q740 quad core CPU's
8GB of RAM
60GB SSD + 500GB HDD
NVidia GeForce GTS 360M - driver
Win 7 Home Premium

View 9 Replies View Related

AutoCAD Civil 3D :: Transition From One Subassembly To Other

Aug 28, 2012

I need to transition to one subassebly to another. The first subassembly is at existing ground the other assembly is above ground. See following picture:

I need to transition from station 12+50 to 13+50. See following picture:

Here is a picture of the Corridor Properties:

Do I need to make a different subassembly in between the two stations? Is there a command I am not seeing that does it for me?

View 9 Replies View Related

AutoCAD Civil 3D :: Where Is The Subassembly Composer

Aug 15, 2013

I know this sounds like a really stupid question.  Where is the subassembly composer?  We have Civil3D 2013, and my understanding was that the subassembly composer was supposed to automatically install in 2013 as opposed to previous years when you had to download it from the Subscription Center.

C3D 2013

View 4 Replies View Related

AutoCAD Civil 3D :: Subassembly Always Is Placed At Right Side

Jul 30, 2013

my subassembly always is placed going to the right.... 

(The sub is avery basic sub.... 4 points .... 1 variable.. no targets.)

Civil 3D (2013)

View 4 Replies View Related

AutoCAD Civil 3D :: FDO Connect To SID

Nov 21, 2013

I've started connecting to Raster (.sid) Aerials thru mapwspace rather than inserting them thru the Planning and Analysis Workstation due to greater control with gray scale and resampling raster and such.  I started noticing after I save, I can't select anything in my drawing.  I was connected to a whole county Aerial .sid file, so i thought maybe if I only connect to individual tiles for my project area which consisted of 9 .sid files, the issue would go away.  It didn't.  I tried typing REA, purge, audit, then eventually I would crash.

Is there something wrong with FDO connections with .sid files thru mapwspace in C3D 2013???

View 1 Replies View Related

AutoCAD Civil 3D :: Express Grass On Subassembly?

Jan 6, 2013

I want to know green area on subassembly.

I attach screenshot.

magenta color line is grass.

How can I express grass on subassembly?

View 2 Replies View Related

AutoCAD Civil 3D :: Mill And Overlay Subassembly?

Mar 1, 2013

I have a project where I am removing existing asphalt pavement and overlaying new pavement.  I am changing the existing profile and cross-slope to tie-in to the existing profile and cross-slope. know of a mill and overlay subassembly that will allow you to tie the edge to a profile or feature line?

View 9 Replies View Related

AutoCAD Civil 3D :: Assigning Material To A Subassembly

Mar 28, 2012

Specifically to Subassembly.LinkWidthAndSlope / I only have Top or Datum options for that sub and if I assign either one in the code set it seems to overwrite all the other subassembly materials such as asphalt, curbs etc...with none set my realisic view has a gap between the back of curb and slope to existing.

Civil 3D 2012 SP1 on Win 7 64-bit SP1
Intel i7-2600kcpu @ 3.4ghz 16mb ram
ATI FirePro V4800

View 3 Replies View Related

AutoCAD Civil 3D :: Subassembly Composer Superelevation

Jul 23, 2013

How to use the superelevation. I read that I have to enter this command:

if((Side=Left)AND(SE.HasLeftLO), SE.LeftLO,
if((Side=Right)AND(SE.HasRightLO), SE.RightLO,

but I don't know where, and I just want to create a simple assembly with a slope and delta X and having a lane outside superelevation for the both side.

View 2 Replies View Related

AutoCAD Civil 3D :: Subassembly Line Colour

Oct 31, 2013

Where do I change the colour of my assembly if I imported it from SAC?

View 1 Replies View Related

AutoCAD Civil 3D :: Cannot Mirror Daylight Subassembly

Apr 26, 2012

Why I can't mirror the Daylight Inside ROW Subassembly? For some reason I can only place it on the right side of my assembly and in the subassembly properties there is no option to flip it to the left. In the Modify Subassembly section when it's selected the mirror option is greyed out. 

What I am trying to accomplish seems simple enough:

I have a utility easement in a drainage ditch that is 30' wide with a sewer line designed down the center, we need a very simple 10' access road on the uphill side of sewer line with 4:1 Cut/Fill slopes on either side when possible, however when the 4:1 won't catch within the easement I need it to daylight within.

At first glance the Daylight Inside ROW seems to be the appropriate subassembly for this instance but I can't get it on the left side of my road.Is there a way to set up this parameter with a different subassembly because I can get other subassemblies on the either side just fine, for example, the Cut Slope Layout Mode subaasembly works but when I build my corridor with it the slopes tie outside of the easement in several locations.

Civil 3D 2012
Windows 7 Service Pack 1
Intel Core i7-2600 CPU

View 5 Replies View Related

AutoCAD Civil 3D :: Tunnel In Subassembly Composer

Jul 13, 2012

I am creating an subassembly for Tunnel in the subassembly composer.I am wondering how can i draw an ellipse with the minor and major radius data.I tried it with curve geometry but it doesn't seem to be way to draw an ellipse with the major and minor axis parameter?

View 7 Replies View Related

AutoCAD Civil 3D :: Editing Subassembly Parameters

Aug 1, 2013

I am using one assembly for this project and of course the existing surface does not always work well with one assembly so I have been using the corridor section editor to adjust each station individually. Attached is a picture of my first station, I started with a 3:1 fore slope (left side) and have changed it to a 2:1 slope. However, my ditch line elevation did not adjust and my parameter editor will not let me adjust the beginning elevation for the ditch line. I am curious as to what the simple solution is for this so my ditchline and back slope or slope to surface will be portrayed correctly.

View 4 Replies View Related

AutoCAD Civil 3D :: Subassembly Name Template Not Working

Sep 4, 2012

For some reason my Subassembly Name Template is not being applied to my subassemblies. This happens in new drawings using the default Imperial Template that ships with the product.

I am showing the settings in a screen capture and the results when I apply them in a screen recording.

Infrastructure Suite/C3D 2013, LDT 2004, Power Civil v8i SS1
WIN 7 64 PRO
HP Pavillion h8xt, i7 2600, 12 GB
RADEON 6450, 1 GB

View 3 Replies View Related

AutoCAD Civil 3D :: Use Conditional Subassembly For Grading?

Jan 8, 2013

I have an alignment running counter clockwise at the perimeter of a septic bed.  I’m trying to use a conditional subassembly for the grading.From 0’ to 5’ of fill, grade to existing @ 3:1.Greater than 5” of fill, add a wall (no more than 4’ high) and grade to existing @ 3:1.

View 7 Replies View Related

AutoCAD Civil 3D :: Autodesk Subassembly Composer

Dec 6, 2011

I have a basic wall sub assembly that I created in SAC.Its looks fine in the SAC but when I import it into Civils it does not work...I have changed the extension from pkt to zip so that I can post it on here

View 5 Replies View Related

AutoCAD Civil 3D :: Subassembly Composer Superelevation

Feb 13, 2013

I am working with SAC , and cant understand how that superelevation works, how to make my models work in CIvil 3d in superelevations... how to build it properly in SAC.  I would rly love to get .pkt file with working model as example  , or at least get some usefull tip.

View 9 Replies View Related

AutoCAD Civil 3D :: Corridor With Conditional Subassembly?

Apr 2, 2012

I am working on implementing Chad Studer's techniques from his presentation at Autodesk University for corridors with conditional subassemblies at the driveways.  Basically I created a corridor with two driveways for a test run.  When I select the corridor and look at the object viewer, there are several lines going to who knows where at both driveways.  But a look at the properties of the finished grade surface generated doesn't show anything out of the ordinary.  I had the conditional subassembly look for a polyline on layer "driveway."  It appears that there may be a gap in the corridor at each end of the pollyline.  I've attached the drawing file. 

View 6 Replies View Related

AutoCAD Civil 3D :: Cut File Conditional Subassembly

Nov 9, 2012

how can one create the cut file conditional subassembly or the horizontal conditional subassembly using subassembly composer?

Civil 3D 2013
HP Pavilion dv6 cor i7
windows 8

View 8 Replies View Related

AutoCAD Civil 3D :: Subassembly Links Not Showing Up?

Mar 9, 2012

I created a simple sub-assembly for a windfarm project but when I bring it into civils none of the links or points show up!

View 3 Replies View Related

AutoCAD Civil 3D :: Section View With Subassembly?

Mar 23, 2012

I am creating section view with my road project. I successfully created center line alignment, surface, surface profile, sample line and section views on every station I needed on my design.

I want to see "subassembly" (travel lane, curb & gutter, sidewalk, 2:1 slope) on my section view. I can block, insert and copy it to my section my manually, but I know this not the right way to do.

View 1 Replies View Related

Copyrights 2005-15, All rights reserved