how can one create the cut file conditional subassembly or the horizontal conditional subassembly using subassembly composer?
Civil 3D 2013
HP Pavilion dv6 cor i7
16GB RAM
windows 8
I have an alignment running counter clockwise at the perimeter of a septic bed. I’m trying to use a conditional subassembly for the grading.From 0’ to 5’ of fill, grade to existing @ 3:1.Greater than 5” of fill, add a wall (no more than 4’ high) and grade to existing @ 3:1.
View 7 Replies View RelatedI am working on implementing Chad Studer's techniques from his presentation at Autodesk University for corridors with conditional subassemblies at the driveways. Basically I created a corridor with two driveways for a test run. When I select the corridor and look at the object viewer, there are several lines going to who knows where at both driveways. But a look at the properties of the finished grade surface generated doesn't show anything out of the ordinary. I had the conditional subassembly look for a polyline on layer "driveway." It appears that there may be a gap in the corridor at each end of the pollyline. I've attached the drawing file.
View 6 Replies View RelatedC3D 2009 - We are grading on a hillside, and need to prioritize our conditional fill situations. First fill at 2:1, if not then build wall and daylight @ 2:1, if not then build full height wall. However the sections are showing all three options where they are applicable. I want it to only show the "best" or "first" solution.
View 9 Replies View Relatedit is possible to define point/link codes using some conditional expressions. When I try to write in an expression under "Link Codes" I get an error. Is there a way to create conditional codes without the use of "decisions"?
View 1 Replies View RelatedI am at a crossroads with this corridor that I have to create in Civil 3D 2011, with a sub assembly that logically seems very simple...the conditions for daylight can be found in "Proposed Cross Section". In short I have 4 fill conditions and 2 cut conditions, based on height above original ground...(there are additional requirements for guardrails and retaining walls but at this point i will settle for my slope reaching original ground)
View 9 Replies View RelatedWhen I use ImportSubassembly API to import my subassembly created by Autodesk Subassembly Composer into my civil project, it reports error-"eFilerError".
the code like this:
atcFile = @"D:9f92eaa4ef514ac982518852e1169932.atc";
itemId = "ab660722-c69d-4ade-b373-0e9f99c94e55";
SubassemblyCollection subassemblyCollection = cDoc.SubassemblyCollection;
ObjectId subassemblyId = subassemblyCollection.ImportSubassembly("TestSubassembly", atcFile, itemId, this.doc.Editor.GetPoint("Select import subAssembly location").Value);
However, it is OK if to import subassembly provided by Cilvil 3D.
I just opened my corridor drawing for the first time in 2009 and was greeted by this error:
Macro file not found at original path specified in subassembly. Updated macro file location to path defined by AECCCONTENT_DIR environment variable.
I'm not familiar with the maco file and the only post I found relating to this said the AECCCONTENT_DIR environment variable was abandoned in 2007.
What i want to do is ; i have a corridor with both right/left sides ending with linktosurface with fixed slope.In some sections my existing surface is not wide enough to get intersection with link to surface with fixed slope. So i want to use this "conditional horizontal target " if my surface is not enough wide for intersection then just intersect or go to the edge of my existing surface. But i learned that surfaces cannot be used as an offset target with that subassembly.
View 9 Replies View RelatedIn particular, I am attempting the infamous task of creating driveway openings using a horizontal target with my sub-assemblies. I referred to the AU 2010 video tutorial that gets passed around here on the boards, and for the most part, it works with ONE tiny exception.
Like in the AU video, I set my conditional target to look for a particular layer, and I first attempted the exercise by placing ONE polyline (i.e. driveway opening) on the layer, and set set conditional "found" and "not found" targets to find this pline. The target found the pline on the layer on the right side of the road where I drew it, and created the opening as hoped, but it created an opening on the LEFT side of the road as well!
What do I have to do to prevent the conditional horizontal targets from ignoring the exact opposite side of the road? In my assembly, the left conditions are set to LEFT, and the right conditions are set to RIGHT, but when the corridor gets modeled, BOTH sides of the road will show an opening even if there is only one pline drawn.
I need to create a corridor that has this section. So I'm using this assembly:
on which I put 3 conditional fill subassemblies on point A, one for fill conditions of more than 2 m that would daylight at 2:1 until it reaches 2 m down and then daylights at 1:3 until it reaches the EG. Then I have another for fill conditions of less than 2 m that only daylights at 2:1 to the EG, and the last one is for all cut conditions.
As expected I have the following problem in some stations that have fill conditions on A of less than 2 m but more than 2 m on B:
Is there any way I can make B the comparison point without having the following problem on cut conditions?
Or that I could create an assembly with the condition that when I have a fill of more than 2 m on point B it daylights, from point B, at 1:3; but when B would be on cut conditions it daylights from A?
I am trying to build a corridor using a conditional slope assembly that considers the roadway and links into the lots.
The corridor is divided into 3 regions. All targeting has been assigned.
The first region appears fine. The second and third show no links beyond the roadway.
(in Inventor Pro 2014,64 bit):
I've made an stairs assembly that contains adaptive parts that are all controlled by the assembly parameters.
Here is my assembly and the controlling parameters. The stringers on the side are made with the frame generator and use the "extend" feature to get the appropriate length, as driven by the parameters. The reason I used frame generator is so that I can easily change sizes of the stringers down the road, if needed. I chose to make the parts associative so I could control all of the parameters from within the assembly instead of opening each part separately.
My goal now is to be able to use this assembly (or something similar) as a template to create new sets of stairs, all to be placed in the same main assembly.
I attempted to duplicate all of the parts (append a "2" at the end of each file name and replace components in the new set of stairs with the 2nd version) but ran into problems with the two stringers. I can't figure out what to do to get the Frame00001 and Skeleton00001 to reassociate to Frame00002 and Skeleton00002. So any time I change my slope, the original stairs will end up trying to copy the new stringers instead of keeping the old ones.
how can I make this assembly reference a new frame, and secondly?
How can I create a subassembly..AND hot to add a Pave 3 option or another subbase depth.
View 9 Replies View RelatedWe are trying to edit a small portion of an existing corridor by adding a generic daylighting subassembly. The add subassembly tool in the Corridor Section editor works, but we get an error because the new sub doesn't have a target surface specified. how to add a target for a sub that is added after the corridor was created?
Civil 3D 2012 & 2013 & 2014
Toshiba Qosmio X505-Q890
2 x i7 - Q740 quad core CPU's
8GB of RAM
60GB SSD + 500GB HDD
NVidia GeForce GTS 360M - driver 8.17.13.0697
Win 7 Home Premium
I need to transition to one subassebly to another. The first subassembly is at existing ground the other assembly is above ground. See following picture:
I need to transition from station 12+50 to 13+50. See following picture:
Here is a picture of the Corridor Properties:
Do I need to make a different subassembly in between the two stations? Is there a command I am not seeing that does it for me?
I know this sounds like a really stupid question. Where is the subassembly composer? We have Civil3D 2013, and my understanding was that the subassembly composer was supposed to automatically install in 2013 as opposed to previous years when you had to download it from the Subscription Center.
C3D 2013
64-bit
my subassembly always is placed going to the right....
(The sub is avery basic sub.... 4 points .... 1 variable.. no targets.)
Civil 3D (2013)
I want to know green area on subassembly.
I attach screenshot.
magenta color line is grass.
How can I express grass on subassembly?
I have a project where I am removing existing asphalt pavement and overlaying new pavement. I am changing the existing profile and cross-slope to tie-in to the existing profile and cross-slope. know of a mill and overlay subassembly that will allow you to tie the edge to a profile or feature line?
View 9 Replies View RelatedSpecifically to Subassembly.LinkWidthAndSlope / I only have Top or Datum options for that sub and if I assign either one in the code set it seems to overwrite all the other subassembly materials such as asphalt, curbs etc...with none set my realisic view has a gap between the back of curb and slope to existing.
Civil 3D 2012 SP1 on Win 7 64-bit SP1
Intel i7-2600kcpu @ 3.4ghz 16mb ram
ATI FirePro V4800
How to use the superelevation. I read that I have to enter this command:
if((Side=Left)AND(SE.HasLeftLO), SE.LeftLO,
if((Side=Right)AND(SE.HasRightLO), SE.RightLO,
CType(slope,Double)))
but I don't know where, and I just want to create a simple assembly with a slope and delta X and having a lane outside superelevation for the both side.
Where do I change the colour of my assembly if I imported it from SAC?
View 1 Replies View RelatedWhy I can't mirror the Daylight Inside ROW Subassembly? For some reason I can only place it on the right side of my assembly and in the subassembly properties there is no option to flip it to the left. In the Modify Subassembly section when it's selected the mirror option is greyed out.
What I am trying to accomplish seems simple enough:
I have a utility easement in a drainage ditch that is 30' wide with a sewer line designed down the center, we need a very simple 10' access road on the uphill side of sewer line with 4:1 Cut/Fill slopes on either side when possible, however when the 4:1 won't catch within the easement I need it to daylight within.
At first glance the Daylight Inside ROW seems to be the appropriate subassembly for this instance but I can't get it on the left side of my road.Is there a way to set up this parameter with a different subassembly because I can get other subassemblies on the either side just fine, for example, the Cut Slope Layout Mode subaasembly works but when I build my corridor with it the slopes tie outside of the easement in several locations.
Civil 3D 2012
Windows 7 Service Pack 1
Intel Core i7-2600 CPU
16GB RAM
I am creating an subassembly for Tunnel in the subassembly composer.I am wondering how can i draw an ellipse with the minor and major radius data.I tried it with curve geometry but it doesn't seem to be accurate.best way to draw an ellipse with the major and minor axis parameter?
View 7 Replies View RelatedI am using one assembly for this project and of course the existing surface does not always work well with one assembly so I have been using the corridor section editor to adjust each station individually. Attached is a picture of my first station, I started with a 3:1 fore slope (left side) and have changed it to a 2:1 slope. However, my ditch line elevation did not adjust and my parameter editor will not let me adjust the beginning elevation for the ditch line. I am curious as to what the simple solution is for this so my ditchline and back slope or slope to surface will be portrayed correctly.
View 4 Replies View RelatedFor some reason my Subassembly Name Template is not being applied to my subassemblies. This happens in new drawings using the default Imperial Template that ships with the product.
I am showing the settings in a screen capture and the results when I apply them in a screen recording.
[URL]
Infrastructure Suite/C3D 2013, LDT 2004, Power Civil v8i SS1
WIN 7 64 PRO
HP Pavillion h8xt, i7 2600, 12 GB
RADEON 6450, 1 GB
I have a basic wall sub assembly that I created in SAC.Its looks fine in the SAC but when I import it into Civils it does not work...I have changed the extension from pkt to zip so that I can post it on here
View 5 Replies View RelatedI am working with SAC , and cant understand how that superelevation works, how to make my models work in CIvil 3d in superelevations... how to build it properly in SAC. I would rly love to get .pkt file with working model as example , or at least get some usefull tip.
View 9 Replies View RelatedI created one section with two assemblies. Main line assembly and offset (second line) assembly. Each assembly has its own alignment and profile.In strait its all ok, but in curve I get strange situation, that I try to solve. (look to the picture)
I add Mark points on Point 1 and 3. Then connect them using Link Slopes Between Points. Knowing that Point 2 is not static, but moving point I can't find any way to connect subassembly edge point to that Point 2.
So how can I connect subassembly to Point 2? Or maybe there is a smarter way to connect points 1 and 3. Slope from 1 to 2 should be 50:1 and from 2 to 3 should be 1.5:1
I created a simple sub-assembly for a windfarm project but when I bring it into civils none of the links or points show up!
View 3 Replies View Related