I had a request come in this morning to generate a spread sheet with all PI's along a route with angles greater than 20°s. Using Civil 3d 2011 I thought the PI station report or any of the reports for that matter would tell me the turned/deflection angle for each PI. However, I have discovered I can get coordinates, bearings etc. but no angles. How to spit out a PI report showing the turned angle for each PI?
View 4 Replies
When I try to run my hydrographs through a pond I get an error stating something to the effect of: Outflow greater than Inflow on Hydrograph 6 for the 50-yr storm.
How can the outflow be greater than what is flowing into it? How the program can calculate this.
I am trying to get the cut volumes for areas that are greater than 15ft of cut for my project. We know that we will be able to get the top 15 feet with heavy equipment but will be drilling and blasting anything greater than 15 feet of cut. This is a different pay item, with greater cost so we need to quantify it.
I've got a composite surface that graphically shows me the elevation bands so I can see the areas that are greater than 15 feet but I'm not sure how to quantify the volumes.
Currently using C3D 2012 with the volume dashboard extension. Have 2013 installed just haven't jumped over yet.
When cleaning up a surface, I've always created an Outer Boundary to define the surface limits so that the triangles wouldn't go where I didn't want them.
I'm trying prepping in hopes of sitting for my Autodesk Civil 3d Certification exam at AU. The chapter I'm currently reading through talks about deleting triangles from the surface.
So now I'm wondering about the pros and cons of both methods.
How does one measure angles greater then 180°, using the angle in measuregeom. i have tried the "Specify vertex" but it always returns the smaller angle, it is not a problem when you use angular in dimangular and specify vertex!
View 6 Replies View RelatedI am running Windows 7 Professional 64 bit, plotting to HP 4500 DesignJet. If I attempt to plot an oversized map the plotter either spits out a blank page or says it plotted the map and no map prints. We have another machine running Vista 64 bit and Map 3D 2011 and it is able to plot just fine. Another machine is running XP and Map 2008 and can plot fine.
I have updated plotter drivers, settings, and I have tried plotting off several .pc3 configurations all ending with the same result. As of right now when I need to plot large maps I have to send an e transmit to my other machine in order to plot, which just isn't going to work.
Is there any way possible to have an angular dimension to denote an angle of greater than 180 degrees?
View 4 Replies View RelatedIs there a way to enter the greater than or equal symbol into a block attribute value...?
For example...TEMP IS >= 20O F
** I have found this problem still exists ranging from AutoCAD 2007 - 2010 **
I'm trying to insert the "greater than or equal" symbol in an MTEXT box. Normally, I just grab the old trusty Character Map utility in Windows to find my symbol and copy/paste into the bext box. The funny thing this time is that it forces the font to be Arial (I'm using Simplex on all my MTEXT objects). Here's something else strange: If I change the font in Character Map to Simplex, there ISN'T a greater than or equal symbol but there IS a less than or equal symbol!
So the next thing I tried was a straight Unicode entry in MTEXT. I first tried "U+2264" for less than or equal and got my nice, simplex symbol but entering "U+2265" still forces an Arial font! Is this simply the way it is or am I missing something here?
Code to select node points an/or text that has a Z value greater than "E1" and less than "E2". (where E1 and E2 are user input values)
View 5 Replies View RelatedI am trying to output a project at higher than 30fps and I am failing miserably. My camera can create 1080 mp4 files at 30fps or 720 mp4 files at 30 or 60fps. I want to creat a video using 720 at 60fps (or near to it).
If I load a 60fps clip and play the clip it runs at the original frame rate. If I play the project however, it plays at 25fps. I have tried to change the project properties, but I cannot select anything higher than 25fps in mpg (or 30fps in avi). Likewise, when I create a video file I am stuck at the lower frame rate. Although I am happy with the 1080X30fps clips and projects; it defeats the object of having a faster camera.
if there are any digital cameras which do image capture with greater than 8 bits per channel? I don't doubt such a camera would be well out of my price range, but I've got into scanning and working with with 16-bit colour and I've got the itch...
does anyone here regularly work in a 16-bit colour space?
I'm having trouble with getting quotation marks to display correctly, they look like 2 stacked >> symbols. They change slightly depending on what font I'm using, but they all ride at the base of the text. I cannot acheive normal looking curly or straight quotes at all.
I have tried switching smart quotes on and off in the preferences, restarting, etc. I've noticed this problem in the past, but I thought it was the font I was using. The same thing happens with Times New Roman. I'm running an up to date version of PSextended CS5, 64bit on win 7 64.
This is regarding a error message by Video Studio Pro X5 understanding a fault message which I got after creating a DVD map. This is the original message in Dutch: "Sommige startframenummers van hoofdstukken zijn groter dan het aantal frames". 533:-2147216477:0 Translation: "Some start frame numbers of chapters are greater than the number of frames"
This was also discussed here - but I can not understand the solution: viewtopic.php?t=24055&p=120629
The situation: I have all the same video files (H.264, 24 bits, 25.000 f/s) [worked with this kind of files a couple times and worked alway very well] I have added some tekst and pictures. Total length of video is 01:50 hour. Starting the procedure DVD creating, with burning the DVD folders on my harddisc. Afther the burning proces I got the fault message.
After creating the DVD map I got the fault message (as describbed above) and found on my harddisc the VIDEO_TS folder with 5 files VTS_01_1 till VTS_01_5. The total time of these loose files is ca. 76 minutes. So I missed a hughe chunk. I got the same fault message when I have created chapters within the videofile but also when I created chapters later at the video menu.
When I do not burning a DVD folder but select creating a video file (DVD-video) than I get separated end files instead of just one big file. Maybe this has the same cause?
I recently started an internship with a company who makes radiators for power transformers. The first task they have given me is to clean up their plant layout file. The file currently has 125 layers in it due to machine blocks dragging in unwanted layers whenever they bought new machines. (presses, rolling machines, powdercoating, welding, ect...) I have been having trouble getting rid of and simplifying their floor plan. I tried creating blocks for each group of machines and changing the layer of the block to the desired layer. This seems to change the block to the right layer, but it still references to the other layers it was previously in. I want to keep the separate colors that show different parts of the machines, but I still need to eliminate the unwanted layers. Is there any way to consolidate the layers while keeping the different colors within the blocks I tried to create?. They have me working on Autocad 2006.
View 5 Replies View RelatedSomehow, in some way, I created a floating toobar for the layers manager. When I click on the layers property button, a "floating" version of it appears. I can close it, dock it, auto-hide it, etc., but can't get rid of it permanently.
I'm using LT 2011, which feels odd after two decades of running the "full strength" versions.
I have my current install set to save the dwg down to 2010. how come the preview images are blank? its only when i save down do the images become blank. if i save in the current version the preview image is there.
View 5 Replies View RelatedI need to know how to eliminate my first tread being part of the landing. I have tried every possible combination of varibles I can find. It happens randomly. when it does if I adjust anything it comes back.
View 4 Replies View RelatedIs it possible to eliminate the Profile listed in the title are? I prefer to view the path in the title area. Sometimes the path can be fairly long and characters get cut off. If I could eliminate the current profile from being listed here, I could view more of the path. See attached.
View 2 Replies View RelatedI am not a regular user of the Inventor General Table. I can make and edit the table with no problems. I want to eliminate the lines from one of the columns while leaving the lines in the remaining columns. I tried to set up the column before inserting it but could not find the column format that would allow me to do that in the Style Editor.
How to do this. I need to also remove the (read only) from the Style Editor.
I have many 3d metal sheet metal drawing. When I put the model into 3d model in to 2d layout, I see many 'lines' on flat surfaces. The 'lines' seem to be showing 'reflective effect'. However, it really cause problem when I give this to my boss. He asked why I cut the sheet metal into so many pieces. How I can set autocad NOT to show those unwanted lines?
View 2 Replies View RelatedWill CC overwrite and eliminate CS6?
View 5 Replies View RelatedI have an image with some text over it and I want to eliminate the text w/out causing damage to the background image,
View 2 Replies View RelatedWhen I use erase it appears a mesh of little squares. How can I eliminate those squares? And can I have permanently the tool toolbar attached?
View 4 Replies View RelatedMy signature block with personal info appears when I post a question. How can I eliminate this? This question was sent via email where I erased signature block as a separate step.
View 2 Replies View RelatedWhen I erase in Photoshop part of a drawing, gray rectangles appear. How can I eliminate them? In other words: every time I erase something, text or drawings, those gray rectangles appear. Is there a way to erase something leaving that part just white, so there I can write or draw whatever is needed?
View 7 Replies View RelatedI have produced some artwork for my the printers in X5 Corel.
The artwork includes two fills using radial fill with two grey colours from the Corel CMYK metalic palette to produce a simulation of a metal finish.
If I output as JPG the moirè is eliminated but as a PDF, even with complex fills going to BITmaps I end-up with the moirè.
This is the output as a JPEG:
and this is the PDF:
Back in the late 60s and 70s I had a 8mm video camera. One of those take 50' of film and send it off for developing. In the 80s I got my first talky Hi8 video camcorder. Back then I had to set up a screen, set my camcorder next to the projector and shoot away. Now I am transferring these videos to DVD so I can open them in VS X3. As might be guessed there is a lot of flicker in the videos.
Is there any way to Eliminate this flicker during post edit in VideoStudio X3?
how to zoom in on an object, and then smooth out the pixels so I can see the object clearly again,
View 5 Replies View Relatedwhen importing my picture-files into Elements 11, it doubled all the files. How can I eliminate those duplicates?
View 1 Replies View RelatedHow do I get rid of this twist in my blend? I've tried to rotate the rectangles to eliminate the twist, but it doesn't seem to fix the issue.
View 2 Replies View Related
