I've just installed ACA 2010 on my laptop on Windows XP64 bit
When I select a command such as the wall or door command. The command starts then exits out before I can draw anything.
one of the pc at my work place seemed to be working funny, compared to the other pc.
For example, the command CO won't work, but instead i have to type CC to copy. The command MA doesn't work at all, and i don't know how to match properties.
Along the way, there are other commands that I encounter before. Basically, it jus feels funny for this PC.
Is there any way to restore every single setting without re-installing the autocad?
When I type PL for polyline and then END or MID or PER they don't work, but they do for lines? Any way to change this? When I manually type in any of these snap commands my OSNAP settings turn off.
View 6 Replies View RelatedI can't see the area where I write commands any more, may be a configuration thing because never happened to me before.
View 2 Replies View RelatedWe have AutoCAD Architecture 2011. By default, our profile does not load the AEC commands. I am looking for a way to enable them in session. Short of this I am looking for what controls them.
We have a custom CUI that loads, it was created from the default AutoCAD one. If I switch to the AutoCAD Architecture profile while in AutoCAD the AEC commands do not become active. If I launch AutoCAD from a shortcut that specifies AutoCAD Architecture profile then the AEC commands do load. I have tried loading the AECARCHXOE cui as a partial CUI in our custom CUI but that does not load the ARC commands (either in session or as a new session)
what controls weather the AEC commands load?
When I give keyboard commands to open, save or save as the program freezes. Pulldown menu to open and save work fine but pulldown save as freezes and freezes when using commands on "A". Happening in 2009 also. Same thing happened yesterday, repair did not fix it, so uninstalled and reinstalled and all was fine. Now today freezing again.
Had a blue screen message yesterday when I turned on the computer, bad spooler something. Are these problems related or just a coincidence? Using Windows XP. Autocad is up to date as is Windows.
I recently upgraded to Civil 3D 2013 and now all of my "Create Surface" commands do not work. I get the message " _AeccCreateSurfaceGridFromDEM Unknown command "AECCCREATESURFACEGRIDFROMDEM".
View 2 Replies View RelatedI am unable to use pull down menu commands, for example when I want to save as, I have to type it manually in the command menu...to open a file I have to type the file name at command line..
when I click save as or any other command from the pull down menu, it does not work, the command line apprars at the buttom of the drawing asking me to manually make an imput...
I am using autocad Architecture 2012. the other day it randomly stopped recognizing most commands. I cannot TRIM, CO, OFFSET, ect. all of the main ones. a couple things still work, If I need to draw a circle I can type D and still input diameter. But for all of the rest of those it says "Unknown Command, press f1 for help."
View 3 Replies View Relatedafter install the last service pack, I can't use the MAPPOLYLINETOPOLYGON command, it works only for the first time;
also, I've personalized the acad.pgp file, changing some commands, but some don't work (as EQ=matchprop); they work right before updating
I am working on someone else's file, using CAD2010..For many lines, Chamfer & Fillet commands do not work, "lines are non coplanar "..In the Properties, all Z = 0
I tried Flatten, nothing changed.
finally I got my express tools ribbon but a lot of commands are missing....REDIR for example....
Don't tell me to reinstall AutoCAD Architcture because I already did it twice!
Don't tell my to select the acetmain.cuix by CUILOAD...because..
I also tried the menuload and the appload command but won't load every single lisp routine
from the express folder...can you imagine how many lisp routines the Express Folder has....
AutoCAD Architecture hasn't got such problems with Express Tools.....
I made my plug-in for Autocad 2012.I register my plug-in in registry and so it's autoloaded.If I open Autocad I saw my toolbar, my message from IExtensionApplication.Initialize and all my commands (marked as [assembly: CommandClass) works fine. No problem.
BUT! If I open autocad file by double click - autocad opened. Now I saw my toolbar, saw my message from Initialize!But any commands didn't work. Autocad said that command is unknown. What can be a problem? My be in Autocad version? I have student version and startup message about it.
Commands Work features is not active in edit base solid.
How to make plane? How to make active ?
just installed CS on to my new computer, and all the key commands i use no longer work. For instance holding down the space bar to get the hand tool isn't working, holding down the shift key when i want to proportionally transform something doesn't work, holding down the apple/command key and the space bar to get the magnifying glass tool doesn't work, and so on...
I have seen under the Edit menu the keyboard shortcuts option, but i never set these short cuts up myself, they were just defaults in photoshop. When i was using CS on my old computer, the key commands i spoke of above worked fine....so what has changed? why don't they work anymore?
It seems that the 'combine zoom and pan commands' option doesn't work correctly. Let's say it doesn't react as i am used to in previous version. now i have to do the undo command or 'ctrl z' many times before i am back at the point where i want to go. I using the middle mouse button often to zoom in and out, and for panning. but now there are a lot of steps to undo if you want to go back.
I tried to switch of and on this option in the options dialog but no difference.
An older gentleman at our company is very much used to having F12 as endpoint, F11 as intersection and F10 as dist. Now that I've upgraded him to 2011, his life is pretty much ruined.
No matter what I try, I can't get the temporary override buttons to work. F10 always does POLAR, F11 always does OTRACK and F12 always does DYN.
How can I kill AutoCAD's default behavior and implement what he wants done?
I have autocad 2011 and commands not working. I reinstall autocad but command not working.
View 2 Replies View RelatedLock/unlock commands have three major problems! No “window selection” to select the layers required to be locked in one go. For example, the “isolate” tool works fine with window selection! In principle, I have no idea about the philosophy beyond which some commands are banned from “window selection!No BUILT-IN icon to Lock All or Unlock All (sure, we can customize it but I’m talking about having this command as built-in)The AutoCAD doesn’t give an alert if a command is applied in the location where particular layers are looked. For example, in many cases, we get into trouble as we move particular objects to discover later that some of the objects were locked! That’s fine, but the AutoCAD should give warnings in case a command is applied where some layers are locked.
View 3 Replies View RelatedHow to print the abbreviations of the commands?
I tried to print all the abbreviation of the commands but couldn’t know how can I do that.
I tried File>Print (as shown in the screenshot), but didn’t work
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
I recently downloaded in my new computer the version of autocad 2011, but when I type letters for the command list to show, it doesnt!
View 1 Replies View RelatedJust recently I have really started to develop LISP routines and I am curious if it is possible to integrate them with a Keyboard call-out.
View 9 Replies View RelatedI've just encountered strange issue and I cannot find the proper solution anywhere.I work in AutoCAD for 5 years and I am used to type commands on the keyboard (I usualy don't use icons in AutoCAD).
I was used to...just cancel all previous commands by ESC key and start typing the command.But since last week I had to click in the command line to write the command in it. How to type commands without annoying clicking in command line?
Just got AutoCad 2012. Commands like Mirror and Copy which involve duplication (no problem with Move or Rotate, for example) will cause AutoCad to not respond for a few minutes. I believe it only is an issue with files brought forward from AutoCad 2000.
View 6 Replies View RelatedI created a command that I no longer use. I actually made a spelling error upon creating it "SUPECLOSE" and I want to delete it.
This is how I created this command: I typed in ALIASEDIT in order to add a new alias to a command.
I then clicked on the "Add" button.
In the "Alias:" field, I typed in "xx"
And in the "AutoCAD Command:" field, I typed in "SUPECLOSE" - which isn't actually an autoCAD command. "SUPERCLOSE" is the command I use to run a custom LISP routine that I created. Upon hitting pressing "OK" to this, AutoCAD prompted me with: "'SUPECLOSE' is a new command, Do you want to add this to your list of commands?"
I said yes. And then shortly afterwards realized the spelling error I had made. Problem is...I don't know how to access this list and delete the new command that I had just created (which does nothing).
We are working in AutoCAD 2010 and the keyboard shortcut commands are not working for one of our users. we are having difficulty getting it back online for her. we tried a menu load for the acad.pgp file and it isn't working .
View 2 Replies View RelatedIs there a list of obsolete commands / variables AutoCAD 2012?
AutoCAD Commands, variables, LISP commands, LISP variables?
I use PaintShop Pro v. 11.20 at work. I was using it as normal one day, and it crashed. This is nothing new, the crash is because I tend to have a lot of programs open at the same time and I had not rebooted my computer soon enough to clear the RAM. The problem occurred when I reopened the paint shop after rebooting, and all commands involving the control key (copy/paste, etc.) as well as the delete key do nothing. Very occasionally, it will allow one of these commands to work, but this is now very rare. If I have an object selected, the highlighting will blink briefly as it does when you try to copy it, but otherwise does nothing. I can still use these commands from the drop-down menus. I think this is probably just some random bug that happened when it crashed for whatever reason. If I can avoid reinstalling that would be preferable, as I would have to have the disks mailed to me by the head office. I looked to see if there was some setting that would put things back to normal but could find nothing. I reset defaults, no change.
View 1 Replies View RelatedThe problem is that AutoCAD 2010, does not recognize any object snap commands, all the other comands work just fine.
I have reinstalled the program and don´t work.
What could be?
We've upgraded to 2012 and have noticed a problem when fast clicking on the mouse when using commands.
For example when using the erase command I would usually type E and then quickly right click and left click. However in 2012 it brings up random command instead of erase i.e. sheetset, publish, ucs etc..Bringing up the text window afterwards it shows
Command: e
ERASE
Select objects: Specify opposite corner: *Cancel*
0 found
Select objects: *Cancel*
Command: _PointCloudIndex
The right click and left click are only processed once.This happens on all commands typed on the command line not just erase
When i'm using the modify commands, the objects that I'm modifying become choppy, and when I zoom in and out with the third button/wheel, the movement of the zoom isn't fluid like it normally is, also It is extremely hard to grab an osnap during this process.
View 2 Replies View Related