AutoCAD 2013 :: Get PDFs To Be 22x36?
May 28, 2013I am trying to get my PDF's to be 22x36. My only available printer is 11x17 and for some reason Adobe Standard that I have isn't working for me.
View 4 Replies
ADVERTISEMENT
AutoCAD 2013 :: Publishing To PDF Is Created Layered PDFs Even Settings Are Off?
Oct 24, 2012I have been ateempting to use the DWG to PDF.pc3 to batch convert a bunch of drawings to PDF. Everything appears to work well but I keep getting layers in my PDF's which I do not want as the slow down printing. I have turned off "include layer information" in the pc3 custom settings and I have also set "Don't include" in the publish options.
I am obvisouly missing something somewhere as I continue to get PDF's with layers.
AutoCAD 2013 :: Get Batch Plot To Plot PDFs To Single File
Sep 30, 2013I have just switched over to 2014 and i cannot for the life of me get my batch plot to plot PDF's to a single file! Instead, it's printing all 37 layouts separate. I tried switching between multi-file & single file in the publish options, but nothing!
i know that it took me a while to perfect my settings the last time i set up a new version, but i am struggling to work it out now.
AutoCad :: Plotting From PDFs
Jun 16, 2008I figure many of you do as I do, drawing things to plot blueprints. It just so happens that I'm often sent PDFs of drawings to plot, but for some reason I have trouble with them.
Suppose I have a standard drawing that is meant for a 24x36 Arch D sheet size. It will always plot 36" because it has to, that is the paper width of the roll. But for some reason, it will stop shy of 24" and cut the paper as much as 4 or 6 inches short, instead of printing the full 24".
The drawing inside the PDF is exactly right, the Adobe Acrobat Reader shows the drawing fine, it fits within the margins, it's not scaled, the sheet size is shown accurately. Based on the visuals and settings, all things are great. I've got the paper set to 36" roll, opaque bond, no scaling because I need it to print accurately.
However, when it prints, some of the drawing is cut off at the bottom and at the top, and instead of 24" it cuts the paper at 18 or 20". I don't get it. It shows 24" in the print wizard, the correct paper size is shown, the preview images looks great. All things check OK, and then it prints and cuts off the graphic and makes a short sheet.
I'm afraid to try scale to 100% or scale to sheet size, because the people who have to use this need to scale it on paper with a ruler and I can't have it stretching or shrinking the print.
What gives with Acrobat printing? Need to plot PDFs accurately? It would be one thing to simply cut the sheet where the graphic ends, but this is actually stopping shy of printing the graphic altogether and cutting the sheet early before it reaches 24".
AutoCad :: Multiple PDFs In One Go?
Oct 24, 2012I have over 150 ISOs made and ready to be converted into PDF but I don't know a way to do this without opening each one idividually and printing it to my PDF writer. There must be an easier and faster way to do bulk PDFs.
View 3 Replies View RelatedAutoCAD Inventor :: Possible To Create 3D PDFs
Feb 16, 2012Is it possible to create a 3D PDF from Inventor 2012? Or is there a third party software that is needed to do this?
View 9 Replies View RelatedAutoCad :: Importing PDFs Of Drawings?
Sep 9, 2010I am wanting to import pdf's of drawings into my AC08. I just want them in there for reference purposes, i draw submittals and have them in pdf format and on paper, just on big jobs nice to be able to just scroll over and reference rooms and such. I dont need them to be to scale or scalable. I copied and pasted some in but they were so small, by the time i zoomed in on them they just look like a bunch of vectors and not very legible.
View 8 Replies View RelatedAutoCad :: Converting DWG Files To PDFs?
Sep 7, 2012I'm used to using AutoCad R14 and just recently had to purchase AutoCad 2010. The printing service that I have to use has to have the drawings in a PDF format and I found out how to make the conversion. However, the lineweights, the linetypes and the linetype scales are all out of wack. I have read about setting up a CBT file, but apparently I'm missing something someplace. I want to plot by color to achieve lineweight. Linetypes and linetype scales are set when the object is drawn, where the default is Continuous and 1 respectively.
View 3 Replies View RelatedAutoCAD LT :: Inserted PDFs Print With Transparency
Feb 24, 2012I have several pdf's that I have inserted into a dwg file and when I attempt to plot the file they print with transparency. I have adjusted the contrast, fade and monochrome settings to no avail (also assigned line weight is not set for transparency). Interestingly, the print preview window shows the attachments correctly, but the resulting pdf file when printed contains the attachments printed very faintly.
View 4 Replies View RelatedAutoCAD Inventor :: 3 Sheet IDW To 3 Separate PDFs
Jul 18, 2012We need to be able to print each sheet to it's own PDF (preferably automatically naming the pdf in the process). I can't seem to find a way to do it in Inventor itself or the Task Scheduler. I imagine it's something that needs to be present in the PDF driver, but CutePDF and Acrobat Printer don't seem to have that option. Is there one that does?
Surprisingly, AutoCAD and Revit BOTH have this ability. Inventor seems to be the only Autodesk packaging lacking the ability.
AutoCad :: Using CorelDRAW To PDFs With Vector Information To DWG
Aug 8, 2011I have been using CorelDRAW to PDF's with vector information to DWG's. It is not something I do often so it was fine. I got a few more PDF drawings and decided to try the converters available. These are the trial versions, but the output seems to be worse than what I get with Corel.
View 7 Replies View RelatedAutoCAD Architecture :: PDFs Take Forever To Plot
Jan 24, 2012Every time I try to plot something with a PDF embedded it takes a very long time to spool and plot. Additionally, a PDF in the drawing slows it down so significantly it's almost not worth using..This happens whether the PDF is less than 1 MB or 50 MB...no difference. Has this been fixed in 2012? Why to PDF's do such a drain on system resources when they're such small files to begin with?
View 5 Replies View RelatedAutoCAD Civil 3D :: Publishing PDFs In 2014
Jul 12, 2013noticed that the file size of pdf's created using the publish command in C3D 2014 are much larger than files created using 2013? I'm talking twice the size in some cases. I've gone through the settings and found no differences, but there must be something I'm missing. When I use the plot command on a single layout, the file sizes are similar, so there must be something in the publish command.
C3D 2014 HF1
AutoCad :: Autopublish Producing PDFs That Won't Print?
Jul 26, 2013Using the autopublish command, I'm getting PDF files that display just fine on my monitor, but then when I try to print I get this series of error messages:
"The document could not be printed."
"There were no pages selected to print."
"A drawing error occurred."
But the most frustrating thing is that it only happens for some .dwg files, not all. It seems that the larger they are and the more pages involved, the more likely they are to produce this error.
EDIT: I just went through and tried to print page by page. It turns out of the 22 pages, the only two that won't print and give the errors above have no viewports and are just two large tables filled with text. Is there anything I can do to these tables to make the pages print?
AutoCad :: Batch Plot To PDFs In 2010?
Jan 6, 2010AutoCAD MEP 2010
I've used batch plot to make pdf copies of my drawings in version 2004 and did not have this issue:
In 2010 when I use batch plot to pdf (say for 5 drawings), it produces one single pdf file with 5 sheets. I want an individual pdf file for each drawing (5 pdfs).
I don't want to have to open each drawing and plot. That's what batch plot is for!
AutoCAD 2010 :: Plot Transparency And PDFs
Jun 8, 2011I am having a problem getting PDFs to plot when I have plot transparency on.
I use the dwg to pdf plot function and with plot transparency on... my hatches work perfectly but my PDFs appears very much screened. (As a 50% or more screen would look) If I turn off the plot transparency, the pdf works perfectly but of course my hatch shades obliterate any line work beneath them.
I was able to convert the PDF to a .tiff, with a graphics program... increase the resolution to 600dpi and use imageattach to bring that in. But it is an extra step for each insert and increased dpi = increased file size.
Other than increasing the resolution on the PDF, any way around this "screening" issue on PDFs when plotting with transparency on?
AutoCAD Print / Plot :: Publish Create Different PDFs
Jul 30, 2013I am trying to print of about 50 sheets of cross sections. When i go to an individual sheet and plot the pdf comes out fine, when i try to publish through sheet set, it put the table on top of the section view.
Additional Details
Both are creating the PDF with acroplot . I am using autocad Civil 3d 2013.
I have attached both PDF's.
AutoCAD 2010 :: Publishing High Quality PDFs
Sep 26, 2012Publishing to PDF as single sheets for insertion into other documents or page managers (such as Indesign) works fine, apart from the fact that it makes crappy work of JPGs should any be embedded in the CAD file. Plotting individually using high quality PDF settings also works but it's difficult with large sets.
Therefore, I would like to publish a tab set to PDF using the plotter named in page setup. However, what this does, is it forces me to pick the file name and locaiton each time, rather than using the one specified in the publish dialog. Is there a way around this? That is, can I make the named plotter behave like the "DWG to PDF" one (that is, name the files automatically)?
If not, can I make the "DWG to PDF" one not compress JPGS?
As to why - I work in a mac environment and everyone draws in Illustrator. I use CAD and many times, for large projects, need this sort of page management. And every once in a while, I need to insert a rendering into a CAD document and then publish.
AutoCAD Civil 3D :: Cannot Xref Or Insert PDFs Into Drawing
Nov 4, 2013I’m having a user profile issue on one computer. I have a user, using windows 7 and AutoCAD Civil 3D 2014 on his work station. When using Civil 3D he has two issues: one, he cannot import Dgn’s. I’ve tried everything it just won’t work. Second, he cannot xref or insert PDF’s into a drawing. Now the reason why I say this is a profile issue is because if I log on to his computer (or anyone else log’s on his computer), I can do all those things in Civil 3D, import DGN’s & insert/xref PDF’s. If this user log’s on my computer, he can do all those things in Civil 3D. Import DGN’s & insert/xref PDF’s. Something with his profile on his computer is corrupt and I’m trying to fix it without deleting and creating another user profile.
View 5 Replies View RelatedAutoCAD Visual LISP / AutoLISP :: Insert All PDFs
Apr 9, 2012is there a way to code inserting all pdfs in a multi-page pdf at once?
another one would be, say, you have several pdfs in your dwg that represent different aspects of the same space so you select them (they are on top of each other) and it puts them into a dynamic block automatically in different visualization states (maybe labeled 01,02,03 etc.) and you make one of the sheets visible with a drop down button.
i might be able to figure out the later if there is a way to do the former.
AutoCAD 2010 :: Can Display Any PDFs That Are Showing In Drawing
May 9, 2012I'm looking for a field or maybe piece of rtext that can display any pdf's that are showing in a drawing, I've had no luck in finding anything that can do it.
View 4 Replies View RelatedAutoCAD Architecture :: PDFs Don't Show Up In Plot Preview
Apr 24, 2013I'm running Autocad Architecture 2013. My .dwg has about 15 pdf's in it (from a consultant that does hand drawings that I scan in, and use the image manager to insert into my drawing). The PDF's range from under 1mb, to 10mb. The PDFs are in model space and within my various drawing sheets, I show them in my drawing sheets via multiple viewports. I noticed that when I go to plot a sheet that has pdfs shown in viewports, and click on PLOT PREVIEW, the PDF's don't show up - everything else shows up, linework, jpegs, etc, but not the PDF's! I fiddled with the viewports and noticed that if some part of the PDF's image frame was visible in the Viewport, the PDF would appear in Print Preview. But if the viewport sat directly over the PDF's image frame, the PDF would not show up in the Plot Preview!!!
Could it be I've exceeded the maximum number of Viewports in my entire .dwg? (I have about 16 sheets), Or, could it be some mysterious autocad system variable that I'm running up against.
AutoCAD Inventor :: Create PDFs With 3D Model Embedded?
Jan 20, 2012I'd like to create pdf's with the 3D model embedded. This could then be viewed, rotated, and Zoomed.
Tetra4D is the software to do this as Adobe X no longer supports it.
AutoCad :: Wipeout Prints Black Form PDFs?
Nov 29, 2007When i use the wipeout command rather than background mask in the Mtext window and plot my layout as a pdf, for some reason the wipeout prints as a black block.
View 9 Replies View RelatedAutoCAD Inventor :: Plotting Individual IDW Sheets From Vault To PDFs
Feb 13, 2013I would like to use the plot function to generate 3 individual PDFs from a 3-sheet idw in Vault.Requirements:
1. Each PDF needs to be named after a certain field that is already populated in iProperties
2. All PDFs need to be output to a fixed folder in Vault
I have tried some iLogic codes and indeed it is possible to do that from within Inventor. But should we need to print a large number of idws that will be a nightmare for me.
AutoCAD 2010 :: PDFs Invisible On One Workstation But Fine On Rest
Oct 4, 2012One of my co-workers is having trouble with pdfs. He can bring them into the drawing, but they show up as dots, and he cannot see anything else.
When I open the same file, the pdf is there plain as day.
Already re-installed CAD.
AutoCad :: Attempting To Publishing Multiple DWG Files To Individual PDFs?
Sep 19, 2011I'm using AutoCAD Mech 2008. is there a way to publish multiple dwg files to individual pdf's.
Right now I typically plot to Adobe PDF, extents/center to plot/fit to paper/monochrome.
Upon doing a search, someone mentioned "AutoPublish" upon closing. Is this an option, and if so, is it my only option?
AutoCad :: Plotted PDFs - Text Turning Into Little White Boxes?
Apr 23, 2013Our company plotted some PDFs using Publish, DWG to PDF and all the text came out fine but when our customer views the text in Bluebeam some of it is replaced by little white squares. It also prints out on their end with the little squares.
Mystery_Squares.png
AutoCAD 2010 :: Trueview - Batch PDFs Corrupted Driver
Mar 21, 2012What Acad2010 or Trueview 2012 uses to create it's bacth PDF's? We got a new plotter last week and it seems to have corrupted that driver somehow. We are no longer able to create batch PDF in either Acad or Trueview. We using both Win XP and Win 7 machines. I don't know if the plotter had anything to do with this problem it just seem that this happend the same time as we installed the plotter. I can use a 3rd party PDF maker to make individual PDF but this takes time, the batch PDF is much more useful for me. I'm hoping I can get the generic PDF driver that autocad uses and reinstall that, but I don't know what it is or where I can find it.
View 6 Replies View RelatedAutoCAD 2010 :: Making Paper Space Pages Into PDFs And DWFs?
Dec 5, 2012How can I convert drawings on paperspace into PDFs and DWFs with the correct scale? I measured everything on paperspace and it's right; but if I convert them to PDFs and DWFs everything srinks a little and the scale doesn't match at all. What settings or ways to match the scale into what it's suppose to be to convert it to PDFs and DWFs?
View 4 Replies View RelatedAutoCAD Print / Plot :: Putting Bookmarks In Multi-Sheet PDFs?
Oct 14, 2011I have found that if you publish to single-sheet .pdf's and then combine the .pdf's into one file using Acrobat, each sheet is bookmarked using the name of the individual files for the bookmark names. However, if you publish to a multi-sheet .pdf, no bookmarks are created. Is there any way to create multi-sheet .pdf's in AutoCad and have bookmarks automatically inserted (using the name of the layout as the bookmark name)?
View 3 Replies View Related