Is there a special snap setting to snap to a point/node? I'm not talking about a endpoint or midpoint or anything like that. I mean a "node" that is set with the "POINT" command. I can't snap to any nodes I create.
View 3 RepliesI am trying to use the DIVIDE command but can't see the points (nodes) it creates after the command is complete. I have the OSNAP setting on to snap to nodes which I can't even see. The QSELECT command let me see that they are indeed in the drawing, and that is the only way I can select them.
View 1 Replies View RelatedThis problem has just started to occur and frankly, I'm totally stuck. When I created 3d objects to represents conduits runs in a building, they worked fine. However, when I saved and reopened my file, the objects are shown in different locations, yet their snap points (endpoints, midpoints, arcs, etc) are shown in the correct location. I have attached an image showing what I mean to clarify. I am using Autocad 2014 and Civil 3D 2014.
View 1 Replies View RelatedUsing AutoCAD Civil 3D 2013, now installing Service Pack 1 (kept crashing, this time it's working though), and I'm trying to find the area of a pathway that I've drawn in 2D with standard lines. Using the area tool, I want to find the area of the path, but it arcs around a 180 degree corner. I tried getting a rough estimate of the area by clicking at several points along each of the arcs, but after clicking a point where the arc joins the straight line of the straight section of the path, it literally won't let me click the next point. I can, however, specify the next point as long as it's nowher near the arc. Same goes for the polyline tool.
Just got an error code for the Service Pack installation, too. "A problem prevented the service pack from being installed, contact your administrator. Error 1603"
I am trying to add the measure command which adds nodes / points to what I select to the tool bar and it wont let me do it when I select it out of the commands search box.
View 3 Replies View RelatedI imported survey data and had auto lines drawn. then I rotated my points/nodes. -- how do i get my linework to update?
View 4 Replies View RelatedI have a block that contains attributes. When I select the block, you can see all the nodes/insert points from the attributes within the text. I was wondering if there is anyway to have the block only show the insertion point of the block and not the attributes? The attached image shows what I am talking about.
View 4 Replies View RelatedMy surveyor gave me a topo survey done in no particular coordinate system. He set up his total station on a PK nail and gave it a coordiante of (5000, 5000, 100). I used this survey to generate a surface.
I also have a site survey of the same site, done in state plane coordinate system. the two surveys have mulitple common points; pk nails, iron pins ect.
What i need to do is move the points for the topo survey over to the survey that is in state plane. A simple move command will not do this.
How do i go about moving these points to thier correct location without having to manually edit the .txt file?
I'm messing around with some commands and I'm currently exploring laylockfadectl/layiso.
They both work just fine of course, but I was wondering if its possible to make ACAD ignore snap points on the locked layers?
I want to move a few snap points on a line but not all of them... Usually I would shift + click each individual snap point and then move but when I have a lot of points it gets pretty time consuming.
If there was a way to drag select multiple snap points in a line.
In my application, users will insert predefined blocks which have simple shapes like rectangle,square or circle.
Users will connect some polyline or lines to the blocks inserted. My task is that blocks must have snap points only on their center so that the polylines must be connected to the block center point not to other points such that midpoints, end points of the edges.
I wonder if there is a way to override snap points of the blocks while other entities' snap points do not change.
While adding a vertex to a survey figure, if I click too near (like within 0.5') a survey point, the new vertex snaps to the survey point and uses its point number as the new vertex. Is there a setting for this snap feature to turn it off or change the tolerance?
View 9 Replies View RelatedOne of the CAD engineer in my office is facing with a new problem. Until two days back she was able to use the "mid between two points" object snap. But recently it dissappeared from the shift+right click short cut menu. method to bring it back to the shortcut menu?
Sunilkumar
Formshore
CALICUT
I upgraded to CS6 (v16) from CS5 and am having trouble with one feature so far. In CS5 I could create objects and move them around the artboard with an indicator that would come up to show me where I wasplacing it. For example a light green indicator would show if the object is centred (with the text 'centred' also visible) or a line extending from this point to the object to indicate how far away it was. Illustrator would also do this for the relative position to other objects as well as the edges of the artboard which made aligning things very easy.
These indicators have disappeared in CS6 and I can't seem to get them back even when using different align options. How can I get this to return in my copy of Illustrator CS6?
Can you move an object while using another object's snap points?
View 4 Replies View RelatedI have a workflow where I will link a few PSD's and the other designers can modify the PSD files in Photoshop while I'm working on different content in the AI file. This allows us to work simultaneously and be more efficient with time, since my AI edits aren't dependant on them fixing up the images - it works great.
What I really need is to link an AI file and be able to snap to points on it while I'm creating a separate AI file - The linked AI isn't changing much but I need to see any updates made to it so I can adjust my AI accordingly - but it requires precision and I have to be able to snap to points/edges.
I've wanted this since Illustrator 10 and I can't believe there's no possible way to link to an AI or PDF and be able to just snap to the points, obviously AI knows about the points and lines, the linked content scales and is vector based. By default I can see the AI file but it has the "X" over it and all I can snap to are the edges/corners of the box it's placed in. This doesn't work for me and I have a hard time believing I'm the first person in the world to want to do a simultaneous workflow. I don't want to be able to edit the linked AI at all, just snap to its points.
CS6 Extended (not beta version)
Windows 7
I need the anchor points to snap to whatever I have my gridlines and subdivisions set to in preferences along with guides I place. When I make the initial anchor points, they snap, but moving them after that, they don't snap. I see the new snap vector to pixel grid, but for the majority of my projects, that will not be used.
I have snap check marked and snap to all selected. Never had this problem before CS6.
I have been using Max 2012 with Backburner 2013 without a problem for the last 8 months. I have just finished a project so I thought I would test the same project that works fine on 2012 on 2013.
On the render server everything works fine. On all the render nodes I get the following error
Application Load error 3ds max adapter error 3ds max process no response
3ds max 2013 is installed on all the render nodes.
I'm really getting tired of problems going from 1 version to the next. how much time goes into testing new versions each year. I would gladly have less upgrades but upgrades that work
So you know how we have the snaps endpoint, perpendicular, midpoint etc. I want to find something like the snap "perpendicular."
Any way to start a line/pline then have it snap to another line at a 45° angle instead of perpendicular?
The only thing I could find was here
[URL]........
but I am not sure what all they are trying to do.
I need to snap to guide lines but the only snap I can get is to the endpoint, which results in some very diagonal lines. I actually have ortho turned on because I need only 90 degree angles. Sometimes I need to move an entire line and I would like it perfectly lined up to the guideline. The line being moved is part of a polyline.
I sometimes do need to start or end at an endpoint but how do I do that then also snap to just anywhere on the guideline while maintinaing a 90 degree angle?
I often draw over topography lines and use them for reference but I don't want to snap to them. Is there any way to view an object and turn off snapping only for that specific object or layer? For instance, can you make frozen layers visible somehow so they can be viewed, but not snapped to? Or is there another way to accomplish this?
View 4 Replies View RelatedI need to be able to snap som lines etc to some hatches. I have set Options - Drafting and unchecked "Ignore hatch objects" and OSNAPHACTH: 1 and it still doesnt snap.
View 9 Replies View RelatedI just switched from Autocad 2007 to 2013. how to display the object snap toolbar? the one with center snap, mid-point snap, etc options?
View 3 Replies View RelatedI'm looking for comments here- Was this a "bug" in AutoCAD 2013 or what?
I teach AutoCAD to high school kids via "cyber school" and one of my students was sending me drawings on which the SNAP was NOT "snapping" parallel to the X axis and the GRID was not present at all-
Here's what I discovered (This is what I wrote to the student):
Your software is AUTOCAD DESIGN SUITE Ultimate 2013 (Student Version)
Your LIMITS are correctly set to 0,0 and 12,9
GRID and SNAP are both set to .25
The problem:
1. The GRID does NOT display no matter what settings are chosen under the GRID command or within the Drafting Settings dialog box on the Grid and Snap tab.
2. The SNAP function does not create VERTICAL and HORIZONTAL lines.
(The SNAP function is not alignning with the X and Y axes.)
When I opened your latest drawing (9.1) and drew a 12 by 9 rectangle using coordinate input (L <enter> 0,0<enter> 12,0<enter> 12,9<enter> 0,9<enter> c<enter>), the resulting rectangle was a bit “off-SNAP”.
That shouldn’t happen.
I Googled “AUTOCAD GRID OFF” and any other combination I could think off.
Though I was able to read dozens of queries about various SNAP and GRID issues, NONE that I found addressed this issue.
I confirmed that SNAP was on and started the LINE command.
As I moved the mouse I watched the coordinates displayed next to the crosshairs.
As I “snapped” from point to point the coordinates SHOULD have always displayed increments of ¼ (.25, .75, 1.0, 1.25, etc) but they did NOT.
As I moved away from the origin (0,0) the ever-growing error could be seen in the coordinate display at the crosshairs.
It was as if the SNAP function was NOT following a “perfect” vertical/horizontal orientation as it moved.
To confirm that I drew a line using coordinates: 0,9 as the start point and 12,9 as the next point.
I restarted the line command and “picked” a start point guided by “snap” that was “close” to the first start point (It wasn’t perfectly on the first line’s start point due the anomaly mentioned in my first paragraph.) and then picked a second point that was “close” to the first line’s endpoint.
The 2 lines were not parallel.
The line drawn with SNAP to dictate its start and endpoints was simply not “horizontal”.
The “Y” coordinate of the start and end points on that line were slightly different.
Somehow the SNAP function was not “snapping” in alignment with the X and Y axes.
After experimenting with settings I found a solution.
But why the solution worked I DO NOT KNOW.
It isn’t “LOGICAL”.
As I typed the command SNAP I saw that command “suggestions” were displayed next to the crosshairs.
I selected these snap options one at a time and through this experimentation I stumbled onto the solution.
The command which “worked” was a command called SNAPANG. In 30 years of working in AutoCAD, both 2D and 3D, I have never used the command SNAPANG.
However, nothing ventured, nothing gained:
I typed the command SNAPANG <enter> then typed 1 <enter>.
Nothing changed.
I reentered the command SNAPANG and then entered the previous value 0 (zero) thinking that I was restoring it to its previous setting and suddenly the GRID appeared and the SNAP followed with perfect alignment with the GRID and in perfect alignment with the X and Y axes. As I entered the LINE command and watched the coordinates displayed at the crosshairs they were now in perfect increments of .25.
As I said initially, since the two command-driven settings that I entered should have simply reversed one another, I have gone into this great detail because I will send this on to AutoCAD’s support people and see if they have any comment. It must be a “bug” in the new version of AutoCAD.
In 2010, I thought I remember the grid snap would automatically turn off when I was in a command for selecting stuff, then after completing my selection, the grid snap would automatically turn back on. For instance, if I wanted to isolate a layer, with grid snap on and set to 1/2x1/2", the object I would try to select would be in the middle of all the grid points and my curser would just jump around it. I'd have to F9 to turn off grid snap, then turn it back on when I was done selecting.
View 3 Replies View RelatedSetting that will turn on snap all of the time instead of just when a command is active. You can't even tell that snap is on unless certain commands are active. The cursors doesn't snap on the BREAK command thus I can't use a two point break with any accuracy because the cursor doesn't snap until after the object is selected.
I need snap ALL THE TIME not just when certain commands are active.
When zooming, I middle click the mouse to bring up osnaps, then type the letter to force the snap I want. That stopped working today: the menu pops up, I type "E", the menu goes away, but it doesn't default to endpoint, there's an "E" on my command line.
I'm not sure if this is a Service Pack 1 issue or not, but I just installed that yesterday.
I have a drawing of Clock Face here (see the picture below), which requires donut for the outer circle. My first question is, looking at the picture, what would be the limits, grid, and snap settings? I made an attempt with the limits (0',0') (12',9'), with Grid =0'-0 1/2", and Snap = 0'-0 1/4", but it didn't work out well. I tried to make the Snap 0'-0 1/32" but it couldn't, neither 0'-0 1/16", nor 0'-0 1/8". Why can't I set the Snap to 0'-0 1/32"?
Next, I would like to know how the outer circle could be constructed with donut. The small inner circle below it is of 1'-11" + 1" + 1" in diameter, that is, 2'-1". If then the Donut (as shown) is to be of 24" inside x 1" thick, the 2'-1" DIA circle would disappear within the thickness of the Donut, leaving no gap between them both. How could this be drawn,
With AutoCAD 2013 for Mac, is there a way to change the snap/grid icons to words? In older versions of AutoCAD you could rt. click and toggle "use icons" on / off.
View 1 Replies View RelatedBefore when I was creating models the origin (0,0,0) was always set in the snap point i started the line in. Now suddenly something happend and now 0,0,0 is always starting in the Original XYZ point.
How do I get back to the old settings?
I am having this problem for the first time with my most recent install of 2014 on a Windows 8 computer. When copying a line or any other object along another line as a base, when I type the distance that I want to copy the object, it deselcts the autosnap vector that I had specified. For example, now when I copy an object along a line at various intervals, I have to move my mouse after entering the distance each time to enable the object snap to reselect the direction I want to copy it (along a line that should stay selected through the object snap: nearest).
Is there some object snap or dynamic input setting that I need to change?