I often draw over topography lines and use them for reference but I don't want to snap to them. Is there any way to view an object and turn off snapping only for that specific object or layer? For instance, can you make frozen layers visible somehow so they can be viewed, but not snapped to? Or is there another way to accomplish this?
View 4 RepliesI was wondering if it's possible to turn snap off on a set of layers whilst keeping it on for others?
View 2 Replies View RelatedSetting that will turn on snap all of the time instead of just when a command is active. You can't even tell that snap is on unless certain commands are active. The cursors doesn't snap on the BREAK command thus I can't use a two point break with any accuracy because the cursor doesn't snap until after the object is selected.
I need snap ALL THE TIME not just when certain commands are active.
We recently had a draftsman that drew with snap on (he no longer works here), and now all the drawings he worked on have this setting turned on. I thought it would be as simple as opening up the drawings and either hitting F9 or clicking on the toggle to turn off snap. That doesn't seem to be the case. Snap mode seems to be tied to individual sheets, and every viewport. I have multiple sheets in a drawing and each sheet has multiple viewports. The last thing I want to do is open every drawing, click in every viewport on every sheet to turn off snap.
I have snapmode set to 0, but it will only turn it of in whatever sheet or viewport is active. I have to write a lisp routine that will go through every viewport on every sheet to set snapmode to 0?
I have lots of layers and I need to turn off all of them not one by one.
View 9 Replies View RelatedSnap commands in X6? I can not get the snap to grid to turn off. The button is off and the setting is set to off in options. Objects seem to snap all over not just to the grid. And the grid snap seems to be out of alignment-I cant seem to get objects to snap exactly to the grid.
The same files reopened in X5 are fine. This started with yesterdays install of 6.2. leaving X2 completely unusable.
Every time I change views in 2013, new layers added to the drawing turn off. How do I stop this? The active layer also defalts to the active one I started with.
View 1 Replies View RelatedTurn on/off layers in the current viewport only, I’m wondering if there is a command that can be plugged on the “quick access toolbar” by which one can turn on/off layers in the current viewport only.
The available command to do so is “Freeze and thaw in current viewport” (attached) and it sounds it can’t be plugged in the “quick access toolbar”!
Is there a way to plug the command “Freeze and thaw in current viewport” in the “quick access toolbar” (attached)?
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
I made an autocad file. with many xref files. there are layers. and the layers are all the same, only the name for the layer its the name of the xref link . but how can i turn it off at once.
View 9 Replies View RelatedIV11, IDW.Is there a way to Disable Midpoint snapping while Dimensioning?It seems to get in the way a lot.A lot of the Lines i have to dimension are small and it's Always trying to dimension to the Midpoints of them rather than end points.Not a bad concept.. just in my case it really gets in the way..So just wondering if there is a setting somewhere to turn it off?
View 9 Replies View RelatedI only thought I hated microsoft. Any settings that will turn on snap all of the time instead of just when a command is active.
View 9 Replies View RelatedIs there away to turn off "Snap to Grid"? You find it under View - Perspective Grid - Snap to Grid. I can turn it off by clicking on it to turn off but it won't stay turned off. I tired to go into my preferences to see if you can keep it off in your setting but I do not see it. A lot of discussion boards talk about in the Transform window "Align new objects to pixel grid" and that is turned off.
View 1 Replies View RelatedOS X 10.8.4, CS6 Illustrator
Working with web icons, and I can not get some things to line up with each other. Either to the left or to the right. I've shut off snap to pixel grid in transform palette.
Is there another, overall way to turn this off?
I guess I created a file with Snap to Pixel Grid turned on.Can't figure out how to turn this off.Created a new file without Pixel Grid Snap enabled and pasted the art into it...still had trouble with aligning points correctly. how to turn off Snap To Pixel Grid?
View 10 Replies View RelatedI need an overrule that can not snaps object in all locked layers. How to do that.
View 9 Replies View RelatedIs there any way to turn off the Timeline 'snap to closest clip' function. I want a small gap between some clips.
View 3 Replies View RelatedI am working on Autocad 2012, and am having a problem drawing on faces under another face, whilst working on 3d objects. I have the view set to 2d wireframe, and can select objects underneath whilst not drawing/modifying anything, however as soon as i try to draw it just selects the uppermost face to draw on.
Is there a button to allow me to snap to different layers whilst drawing?
So you know how we have the snaps endpoint, perpendicular, midpoint etc. I want to find something like the snap "perpendicular."
Any way to start a line/pline then have it snap to another line at a 45° angle instead of perpendicular?
The only thing I could find was here
[URL]........
but I am not sure what all they are trying to do.
I need to snap to guide lines but the only snap I can get is to the endpoint, which results in some very diagonal lines. I actually have ortho turned on because I need only 90 degree angles. Sometimes I need to move an entire line and I would like it perfectly lined up to the guideline. The line being moved is part of a polyline.
I sometimes do need to start or end at an endpoint but how do I do that then also snap to just anywhere on the guideline while maintinaing a 90 degree angle?
my gimp 2.8.6 makes majority normal layers turn into text layers..
Even if i "discard text information" from layer..and then save it as .xcf it doesnt work! Same layers appear as text layers when i open that .xcf Its not a big deal but it really slows me down when im working with layers..
I need to be able to snap som lines etc to some hatches. I have set Options - Drafting and unchecked "Ignore hatch objects" and OSNAPHACTH: 1 and it still doesnt snap.
View 9 Replies View RelatedIs there a special snap setting to snap to a point/node? I'm not talking about a endpoint or midpoint or anything like that. I mean a "node" that is set with the "POINT" command. I can't snap to any nodes I create.
View 3 Replies View RelatedI just switched from Autocad 2007 to 2013. how to display the object snap toolbar? the one with center snap, mid-point snap, etc options?
View 3 Replies View RelatedThis problem has just started to occur and frankly, I'm totally stuck. When I created 3d objects to represents conduits runs in a building, they worked fine. However, when I saved and reopened my file, the objects are shown in different locations, yet their snap points (endpoints, midpoints, arcs, etc) are shown in the correct location. I have attached an image showing what I mean to clarify. I am using Autocad 2014 and Civil 3D 2014.
View 1 Replies View RelatedUsing AutoCAD Civil 3D 2013, now installing Service Pack 1 (kept crashing, this time it's working though), and I'm trying to find the area of a pathway that I've drawn in 2D with standard lines. Using the area tool, I want to find the area of the path, but it arcs around a 180 degree corner. I tried getting a rough estimate of the area by clicking at several points along each of the arcs, but after clicking a point where the arc joins the straight line of the straight section of the path, it literally won't let me click the next point. I can, however, specify the next point as long as it's nowher near the arc. Same goes for the polyline tool.
Just got an error code for the Service Pack installation, too. "A problem prevented the service pack from being installed, contact your administrator. Error 1603"
I'm looking for comments here- Was this a "bug" in AutoCAD 2013 or what?
I teach AutoCAD to high school kids via "cyber school" and one of my students was sending me drawings on which the SNAP was NOT "snapping" parallel to the X axis and the GRID was not present at all-
Here's what I discovered (This is what I wrote to the student):
Your software is AUTOCAD DESIGN SUITE Ultimate 2013 (Student Version)
Your LIMITS are correctly set to 0,0 and 12,9
GRID and SNAP are both set to .25
The problem:
1. The GRID does NOT display no matter what settings are chosen under the GRID command or within the Drafting Settings dialog box on the Grid and Snap tab.
2. The SNAP function does not create VERTICAL and HORIZONTAL lines.
(The SNAP function is not alignning with the X and Y axes.)
When I opened your latest drawing (9.1) and drew a 12 by 9 rectangle using coordinate input (L <enter> 0,0<enter> 12,0<enter> 12,9<enter> 0,9<enter> c<enter>), the resulting rectangle was a bit “off-SNAP”.
That shouldn’t happen.
I Googled “AUTOCAD GRID OFF” and any other combination I could think off.
Though I was able to read dozens of queries about various SNAP and GRID issues, NONE that I found addressed this issue.
I confirmed that SNAP was on and started the LINE command.
As I moved the mouse I watched the coordinates displayed next to the crosshairs.
As I “snapped” from point to point the coordinates SHOULD have always displayed increments of ¼ (.25, .75, 1.0, 1.25, etc) but they did NOT.
As I moved away from the origin (0,0) the ever-growing error could be seen in the coordinate display at the crosshairs.
It was as if the SNAP function was NOT following a “perfect” vertical/horizontal orientation as it moved.
To confirm that I drew a line using coordinates: 0,9 as the start point and 12,9 as the next point.
I restarted the line command and “picked” a start point guided by “snap” that was “close” to the first start point (It wasn’t perfectly on the first line’s start point due the anomaly mentioned in my first paragraph.) and then picked a second point that was “close” to the first line’s endpoint.
The 2 lines were not parallel.
The line drawn with SNAP to dictate its start and endpoints was simply not “horizontal”.
The “Y” coordinate of the start and end points on that line were slightly different.
Somehow the SNAP function was not “snapping” in alignment with the X and Y axes.
After experimenting with settings I found a solution.
But why the solution worked I DO NOT KNOW.
It isn’t “LOGICAL”.
As I typed the command SNAP I saw that command “suggestions” were displayed next to the crosshairs.
I selected these snap options one at a time and through this experimentation I stumbled onto the solution.
The command which “worked” was a command called SNAPANG. In 30 years of working in AutoCAD, both 2D and 3D, I have never used the command SNAPANG.
However, nothing ventured, nothing gained:
I typed the command SNAPANG <enter> then typed 1 <enter>.
Nothing changed.
I reentered the command SNAPANG and then entered the previous value 0 (zero) thinking that I was restoring it to its previous setting and suddenly the GRID appeared and the SNAP followed with perfect alignment with the GRID and in perfect alignment with the X and Y axes. As I entered the LINE command and watched the coordinates displayed at the crosshairs they were now in perfect increments of .25.
As I said initially, since the two command-driven settings that I entered should have simply reversed one another, I have gone into this great detail because I will send this on to AutoCAD’s support people and see if they have any comment. It must be a “bug” in the new version of AutoCAD.
In 2010, I thought I remember the grid snap would automatically turn off when I was in a command for selecting stuff, then after completing my selection, the grid snap would automatically turn back on. For instance, if I wanted to isolate a layer, with grid snap on and set to 1/2x1/2", the object I would try to select would be in the middle of all the grid points and my curser would just jump around it. I'd have to F9 to turn off grid snap, then turn it back on when I was done selecting.
View 3 Replies View RelatedI know there is a command/button to turn all layers back on if most of them are off, and you want them back on. I use it all the time.
My question: is there a similar command to turn them all off? If not, why not? It makes just as much sense to me. Sometimes I want to turn all of them off, and then just turn one back on.
When zooming, I middle click the mouse to bring up osnaps, then type the letter to force the snap I want. That stopped working today: the menu pops up, I type "E", the menu goes away, but it doesn't default to endpoint, there's an "E" on my command line.
I'm not sure if this is a Service Pack 1 issue or not, but I just installed that yesterday.
I have a drawing of Clock Face here (see the picture below), which requires donut for the outer circle. My first question is, looking at the picture, what would be the limits, grid, and snap settings? I made an attempt with the limits (0',0') (12',9'), with Grid =0'-0 1/2", and Snap = 0'-0 1/4", but it didn't work out well. I tried to make the Snap 0'-0 1/32" but it couldn't, neither 0'-0 1/16", nor 0'-0 1/8". Why can't I set the Snap to 0'-0 1/32"?
Next, I would like to know how the outer circle could be constructed with donut. The small inner circle below it is of 1'-11" + 1" + 1" in diameter, that is, 2'-1". If then the Donut (as shown) is to be of 24" inside x 1" thick, the 2'-1" DIA circle would disappear within the thickness of the Donut, leaving no gap between them both. How could this be drawn,
With AutoCAD 2013 for Mac, is there a way to change the snap/grid icons to words? In older versions of AutoCAD you could rt. click and toggle "use icons" on / off.
View 1 Replies View Related