I'm messing around with some commands and I'm currently exploring laylockfadectl/layiso.
They both work just fine of course, but I was wondering if its possible to make ACAD ignore snap points on the locked layers?
I need an overrule that can not snaps object in all locked layers. How to do that.
View 9 Replies View RelatedI am trying to use the DIVIDE command but can't see the points (nodes) it creates after the command is complete. I have the OSNAP setting on to snap to nodes which I can't even see. The QSELECT command let me see that they are indeed in the drawing, and that is the only way I can select them.
View 1 Replies View RelatedIs there a special snap setting to snap to a point/node? I'm not talking about a endpoint or midpoint or anything like that. I mean a "node" that is set with the "POINT" command. I can't snap to any nodes I create.
View 3 Replies View RelatedI want to move a few snap points on a line but not all of them... Usually I would shift + click each individual snap point and then move but when I have a lot of points it gets pretty time consuming.
If there was a way to drag select multiple snap points in a line.
This problem has just started to occur and frankly, I'm totally stuck. When I created 3d objects to represents conduits runs in a building, they worked fine. However, when I saved and reopened my file, the objects are shown in different locations, yet their snap points (endpoints, midpoints, arcs, etc) are shown in the correct location. I have attached an image showing what I mean to clarify. I am using Autocad 2014 and Civil 3D 2014.
View 1 Replies View RelatedUsing AutoCAD Civil 3D 2013, now installing Service Pack 1 (kept crashing, this time it's working though), and I'm trying to find the area of a pathway that I've drawn in 2D with standard lines. Using the area tool, I want to find the area of the path, but it arcs around a 180 degree corner. I tried getting a rough estimate of the area by clicking at several points along each of the arcs, but after clicking a point where the arc joins the straight line of the straight section of the path, it literally won't let me click the next point. I can, however, specify the next point as long as it's nowher near the arc. Same goes for the polyline tool.
Just got an error code for the Service Pack installation, too. "A problem prevented the service pack from being installed, contact your administrator. Error 1603"
In my application, users will insert predefined blocks which have simple shapes like rectangle,square or circle.
Users will connect some polyline or lines to the blocks inserted. My task is that blocks must have snap points only on their center so that the polylines must be connected to the block center point not to other points such that midpoints, end points of the edges.
I wonder if there is a way to override snap points of the blocks while other entities' snap points do not change.
While adding a vertex to a survey figure, if I click too near (like within 0.5') a survey point, the new vertex snaps to the survey point and uses its point number as the new vertex. Is there a setting for this snap feature to turn it off or change the tolerance?
View 9 Replies View RelatedOne of the CAD engineer in my office is facing with a new problem. Until two days back she was able to use the "mid between two points" object snap. But recently it dissappeared from the shift+right click short cut menu. method to bring it back to the shortcut menu?
Sunilkumar
Formshore
CALICUT
I upgraded to CS6 (v16) from CS5 and am having trouble with one feature so far. In CS5 I could create objects and move them around the artboard with an indicator that would come up to show me where I wasplacing it. For example a light green indicator would show if the object is centred (with the text 'centred' also visible) or a line extending from this point to the object to indicate how far away it was. Illustrator would also do this for the relative position to other objects as well as the edges of the artboard which made aligning things very easy.
These indicators have disappeared in CS6 and I can't seem to get them back even when using different align options. How can I get this to return in my copy of Illustrator CS6?
Can you move an object while using another object's snap points?
View 4 Replies View RelatedI have a workflow where I will link a few PSD's and the other designers can modify the PSD files in Photoshop while I'm working on different content in the AI file. This allows us to work simultaneously and be more efficient with time, since my AI edits aren't dependant on them fixing up the images - it works great.
What I really need is to link an AI file and be able to snap to points on it while I'm creating a separate AI file - The linked AI isn't changing much but I need to see any updates made to it so I can adjust my AI accordingly - but it requires precision and I have to be able to snap to points/edges.
I've wanted this since Illustrator 10 and I can't believe there's no possible way to link to an AI or PDF and be able to just snap to the points, obviously AI knows about the points and lines, the linked content scales and is vector based. By default I can see the AI file but it has the "X" over it and all I can snap to are the edges/corners of the box it's placed in. This doesn't work for me and I have a hard time believing I'm the first person in the world to want to do a simultaneous workflow. I don't want to be able to edit the linked AI at all, just snap to its points.
CS6 Extended (not beta version)
Windows 7
I need the anchor points to snap to whatever I have my gridlines and subdivisions set to in preferences along with guides I place. When I make the initial anchor points, they snap, but moving them after that, they don't snap. I see the new snap vector to pixel grid, but for the majority of my projects, that will not be used.
I have snap check marked and snap to all selected. Never had this problem before CS6.
I isolated layers to clear out a drawing, since then I have had nothing but hassle with locked layers, No matter how many times I unlock them, they lock up again, if I create a new layer it comes in locked, if I change a line to a differant layer it locks up, I have tried creating a few simple layers, then copying and pasting the layout into a new drg file, still the problem exists, it is costing me a lot of time having to keep doing this.
View 9 Replies View RelatedI am trying to assign objects (only in UNLOCKED layers) with a new layer.So basically, the user will select all the objects in the drawing.
After selecting (ex. press enter after window selecting), only objects in UNLOCKED layers will have a new layer.
Following is the code I am using...But I keep getting eOnLockedLayer exception.How should I handle this issue?
using (Transaction acTrans = acCurDb.TransactionManager.StartTransaction())
{
PromptSelectionOptions pSelOpts = new PromptSelectionOptions();
pSelOpts.MessageForAdding = "Select all objects";
PromptSelectionResult pSelRes = acDoc.Editor.GetSelection(pSelOpts);
if (pSelRes.Status == PromptStatus.OK)
[code]....
I've locked a layer and this one went off, too. This is AutoCAD 2010, it's because the program?
I want my layer ON but locked, what can I do?
My ACad2006 Layer Combo Control bar appears to be locked. It will only show the current layer and will not show the layer of an object that is selected with the pickbox. I must have accidentally made a change somehow, but don't know how to undo this.
View 2 Replies View RelatedI used PENZD file that has 8 points (4 locations with 2 depths in each location) to create a Point dwg that has several annotations I made. Then I used the
"Lines/Curves" => "Create Lines" by "Point # Range" to create 6 sets of lines:
Line Set #1 that connects Points 1-3-5-7-1,
Line Set #2 that connects Points 2-4-6-8-2,
Line Set #3 that connects Points 1-2,
Line Set #4 that connects Points 3-4,
Line Set #5 that connects Points 5-6,
Line Set #6 that connects Points 7-8.
The annotaions for the 8 points are gone, after I completed the creation of the Lines. I wonder whether I can create 2 layers in the AutoCAD Civil 3D 2013: 1 layer for the 8 points with my annotations attached and 1 layer for the lines I created from the 8 points.
I have a question regarding AutoCAD 2012 and when it comes to locking layers.
When working on the basement layer I would like to see that layer locked in turn not affecting my other layers, ie: my house/garage/second-floor.
I'm working in 2011. Just labeling some contours in a new drawing, using the 'Multiple' setting. I found I could only draw one tangent of Contour Label Line. If I continued, I could click but no labels were created and on finishing the command I could see that those clicks had been ignored. What gives?
I found that the labels were on the current layer, instead of the layer they're meant to use.I also realised that my current layer was locked (from the previous task).
if the current layer is locked, the contour labels ignore the layer setting that they are meant to use, and come in on the current layer instead. And you can only draw one tangent's worth of contour labels at a time before finishing the command and restarting.
Solution: make a different layer current or unlock your layer.
are contour labels generally created on the current layer and then moved to their proper layer?Is that why it hit a snag: it wasn't permitted to move the object to a different layer because the one it was on was locked?
I have a form with a combobox and a commandbutton.
All layers in the layermanager must be locked except the active layer chosen in the combobox. I try it with this code but it’s not the right solution.
Private Sub CommandButton1_Click()Dim layer As AcadLayer'check if all layers are lockedIf layer.Lock = False Thenlayer.Lock = True'make the layer selected in the combobox currentThisDrawing.ActiveLayer = ThisDrawing.Layers.Item(ComboBox1.Text)End SubPrivate Sub UserForm_Initialize() Dim layerColl As AcadLayers Dim layer As AcadLayer Dim LayList As String ' all layers locked For Each layer In ThisDrawing.Layers If layer.Lock = False Then layer.Lock = True End IfNext 'fill combobox Set layerColl = ThisDrawing.Layers For Each layer In layerColl ComboBox1.AddItem layer.Name Next End Sub
2. When I choose the for next method to lock all layers (40 layers) it’s very slow.
Normally when a layer is locked, you hover your cursor over the locked layer on screen you will be able to see a small [Lock Pad]
kinda icon ...
{ Please refer to the attach image for explanation ... }
How to turn of the "lock symbol" from showing when you run your crosshairs (outside of a command) over a locked layer. Its annoying and i would like to turn it off.
Also, when offsetting a line, is there a way to turn off the imaginary offset line that indicates the offset side, again its annoying and i'd like to turn it off.
Is there a LISP code for disabling OSNAP for specific objects or layers? An automatic disable for multileaders would be useful when fine tuning the text placement. Trouble is you need the snap for the leader end. Maybe you could disable the snap for the text grip only.
View 1 Replies View RelatedI've recently switched from 6 to 7. When I open an image the layer is locked and I can't unlock it (greyed out). This prevents me from adding the drop shadows I need to add. Any answers out there, please?
View 4 Replies View RelatedWhat is/are the benefits of having every background layer of a newly opened document locked? I have never come across a need for it and wish it wasn't. It only means I have to create a new layer and import an image to that. Or, double click the layer to unlock it. Is there a way to permanently eliminate that "preference?" It's like entering a room with your shoes tied together.
View 7 Replies View RelatedI am using CS4. I have a partially locked layer. It is not the background layer. I partially locked it myself but forgot how I did it. How do I unlock it?
View 2 Replies View Relatedone layer in a photoshop document has a padlock on it; no clue how it got there. I can't make it go away; perhaps the method is different in CS6 than in previous versions...
Any clue about this? I can't fill a selection on this particular layer...don't know why. The layer in question IS selected, and the selection is active, etc.
CS5 - the background layer - although it shows as being locked - it is not -- when I add a new layer the new information also changes in the background layer - how do you fix that?
View 4 Replies View RelatedI start a new document and try to paint on it I get some warning that the layer is locked or some garbage, so I create a new layer and try to paint on that and it's like stuck on the move tool or something, even though it clearly has the brush tool selected.
View 7 Replies View Related