I have a question regarding AutoCAD 2012 and when it comes to locking layers.
When working on the basement layer I would like to see that layer locked in turn not affecting my other layers, ie: my house/garage/second-floor.
How to turn of the "lock symbol" from showing when you run your crosshairs (outside of a command) over a locked layer. Its annoying and i would like to turn it off.
Also, when offsetting a line, is there a way to turn off the imaginary offset line that indicates the offset side, again its annoying and i'd like to turn it off.
I have a form with a combobox and a commandbutton.
All layers in the layermanager must be locked except the active layer chosen in the combobox. I try it with this code but it’s not the right solution.
Private Sub CommandButton1_Click()Dim layer As AcadLayer'check if all layers are lockedIf layer.Lock = False Thenlayer.Lock = True'make the layer selected in the combobox currentThisDrawing.ActiveLayer = ThisDrawing.Layers.Item(ComboBox1.Text)End SubPrivate Sub UserForm_Initialize() Dim layerColl As AcadLayers Dim layer As AcadLayer Dim LayList As String ' all layers locked For Each layer In ThisDrawing.Layers If layer.Lock = False Then layer.Lock = True End IfNext 'fill combobox Set layerColl = ThisDrawing.Layers For Each layer In layerColl ComboBox1.AddItem layer.Name Next End Sub
2. When I choose the for next method to lock all layers (40 layers) it’s very slow.
How to select a locked layer when you have too many layers overlapping?
I know I can select all the layers, lock them and unlock them. But I can't lock/unlock all layers when some layers are hidden. I'll have to dig in to unhide those layers. But then I don't want to unhide all layers, because it will make changes to my design that I wouldn't know.
Is there a smart way to find/select the lock layer?
In model space if i go to layers manager and turn off a layer why does it still show up in model space. Civil 3d 2013
View 4 Replies View RelatedI made a wax seal on Photoshop with a lot of embossment, bedevilment and a Smart Filter. It's done and I just need to make it smaller so it fits well on my certificate. When I resize it (Ctr + T) It pops up a message that reads:
______________________________________________
Adobe Photoshop CS6 Extended
"Smart Filters applied to layers contained in this group will be turned off temporarily while the transform is being previewed. They will be applied after committing the transform."
OK
[] Don't show again
______________________________________________
I click OK and I re-size the layer with free transform, and then hit enter. The Layer is resized but my Smart Filter which creates a wavy affect around the seal is totally distorted.
How do re-size my layer with smart filter without affecting the smart filter aspect of the layer.
How do i Turn Multiple Text Layers into 1 Layer Style?
View 1 Replies View RelatedI have found that when I use the Layer Styles on one layer and then make a new layer or select a shape that creates a new layer that when I go to add Styles to the new layer/new shape the previous layer is affected by how I set the Bevel & Emboss, Direction, Altitude, Drop Shadow etc etc.
For instance, let's say I have a ...
BG > New Layer > draw an ellipse and then add a Bevel with an > Angle of 89 and an Altitude of 30 and then I add a New Layer > open the Styles and go to change the Angle to say +89 or whatever and the Altitude to say 45 ... the first Layer/Shape Effects change.
How I can keep one Layer from being affected by an other Layers Effects'?
I have found that if I Rasterize a Layer Effect that I can add a "double" effect on the same layer but I haven't tried the to do this with separate layers. However, for most of the work I am doing I cannot use the Raster because everything needs to be true vectors.
I have a Dell Laptop/Windows 7 Home Premium that's a 64 bit
I have this picture with 10 layers... normal, masks etc.. all sort of stuff..now, I want to change the colour of a selection of the picture, but I dont want to flatten it first... how to I do that? I tried a replace colour mask, but that seems to apply to only 1 layer ....
View 1 Replies View RelatedI use the layer effect Drop Shadow with several layers. Now I wanted to have another angle for a specific layer, but this affects all other layers, too! How can I edit the angle without affecting the other layers?
View 3 Replies View RelatedWe are using color profiles that adjust the white point. When these color profiles are applied to the image we cannot properly paint into layer masks because we cannot access "pure white". The brightest white we can paint with is a form of grey (aka, we cannot paint back full opacity in a layer mask). This shows up in the color "chips" as only allowing the brightest value to be a light grey. The only way to get around this is to turn off our color profile, paint pure white, and then reapply the color profile (which confirms my understanding that "pure white" is supported by the mask channel when a color profile is applied, we just cannot paint it that value when the profile is applied).
As far as I can imagine, color profiles shouldn't be applied to scalar channels like a mask channel, right?
This affects CS2, CS3, CS4, CS5 and CS6
I need an overrule that can not snaps object in all locked layers. How to do that.
View 9 Replies View RelatedIn my layer prop manager, I have 2 layers with the name "0". How is this possible? Also, I'm trying to move the lines/polylines on either one of these layers and it won't move because it's locked. But when you look on the layer manager, BOTH of the 0 layers are not locked down.
View 5 Replies View RelatedI have this application: It's a userform with a combobox filled up with all layers. There also are 2 commandbuttons and a label.When I apply the command button all the layers except the selected layer in the combobox lock. That's good.This is the problem:
Normaly when I lock a layer it is fading (laylockfadectl 80). But when I lock layers with this vba code it doesn't fading locked layers.
Option ExplicitPrivate Sub cmbx1_Change()Label1.Caption = cmbx1.ValueEnd SubPrivate Sub cmdAPPLY_Click()On Error Resume Next 'handle exceptions inline
Dim objlayers As AcadLayersDim objlayer As AcadLayer
Set objlayers = ThisDrawing.Layers 'make the layer selected in the combobox current
[code]....
where is the setting to change the Fade Control when you lock a layer?(It is not the same as the Fade Control of the External References in the Display tag of the Options dialog. I know that one and I am aware of this one.)
The one that I want to know is of the locked layers. When I lock a layer, the objects in the layer fade.
locked objects get selected, but nothing acts on them. that is i do see them getting dotted while i selected all objects on other unlocked layers. is there way that locked layers don't get dotted while selection? just like in sketchup?
View 5 Replies View RelatedI have made gridlines and put them on a locked layer. I want to be able to see them and snap to them, but I don't want to select them. Their selectability is hindering my ability to select objects on other layers. Is there any way to make lines on locked layers not selectable? (I don't like the Autocad standard grid.)
View 9 Replies View Relatedhow to adjust the transparency of locked layers? Also when I isolate a layer the other layers appear semi transparent, is it the same setting to adjust this transparancy as well?
View 2 Replies View RelatedCreate a command (macro) to unlock all locked layers and remove the fade effect. I know how to unlock them by using the command LAYULK, selecting the entities on the locked layer. I have been trying to automate the command so I don't have to select entities.
View 4 Replies View RelatedI have a drawing where I need to open the layer manager to turn on a layer in a view port but cannot get to that particular column. As you look across the top of the layer manager I can see all the headings of each column beginning with "Name", "Status", "On" and so forth. The last column heading I see is "Description" but I need to go even further to the right to get to the column I need to be at but can't get there. There is no scroll button on the bottom of the layer manager which would allow me to do that.
View 7 Replies View RelatedI isolated layers to clear out a drawing, since then I have had nothing but hassle with locked layers, No matter how many times I unlock them, they lock up again, if I create a new layer it comes in locked, if I change a line to a differant layer it locks up, I have tried creating a few simple layers, then copying and pasting the layout into a new drg file, still the problem exists, it is costing me a lot of time having to keep doing this.
View 9 Replies View RelatedThe routine below delete group of blocks by name, but if the blocks are on locked layers, these are not removed.
How can improve the lisp?
(defun c:deleteblock (/ rn ss)(defun Jd (realname) (setq ss (ssget "x" (list '(0 . "INSERT")(cons 2 (strcat "`*U*," REALNAME))))) (mapcar '(lambda (x) (if (not (eq REALNAME (vla-get-effectivename (vlax-ename->vla-object (cadr x))))) (ssdel (cadr x) ss))) (ssnamex ss))(setq ss_len (sslength ss)) (command "_erase" ss "") ) (setq rn (vla-get-effectivename (vlax-ename->vla-object (car (entsel "
Select the block you want to delete:"))))) (jd rn) (princ (strcat "
" (itoa ss_len) " Blocks called "" rn "" has been deleted")) (princ) )
I am trying to assign objects (only in UNLOCKED layers) with a new layer.So basically, the user will select all the objects in the drawing.
After selecting (ex. press enter after window selecting), only objects in UNLOCKED layers will have a new layer.
Following is the code I am using...But I keep getting eOnLockedLayer exception.How should I handle this issue?
using (Transaction acTrans = acCurDb.TransactionManager.StartTransaction())
{
PromptSelectionOptions pSelOpts = new PromptSelectionOptions();
pSelOpts.MessageForAdding = "Select all objects";
PromptSelectionResult pSelRes = acDoc.Editor.GetSelection(pSelOpts);
if (pSelRes.Status == PromptStatus.OK)
[code]....
I've locked a layer and this one went off, too. This is AutoCAD 2010, it's because the program?
I want my layer ON but locked, what can I do?
I'm messing around with some commands and I'm currently exploring laylockfadectl/layiso.
They both work just fine of course, but I was wondering if its possible to make ACAD ignore snap points on the locked layers?
My ACad2006 Layer Combo Control bar appears to be locked. It will only show the current layer and will not show the layer of an object that is selected with the pickbox. I must have accidentally made a change somehow, but don't know how to undo this.
View 2 Replies View Relatedi am trying to restrict users from modifying certain attributes in a block,i can create the blocks with some of the attributes on locked layers, but then autocad pops up an annoying alert box, is there a way to disable this? the other option i can think of is to redefine the commands *ddedit, *attedit, *ddatte,*attipedit,
View 5 Replies View RelatedI'm working in 2011. Just labeling some contours in a new drawing, using the 'Multiple' setting. I found I could only draw one tangent of Contour Label Line. If I continued, I could click but no labels were created and on finishing the command I could see that those clicks had been ignored. What gives?
I found that the labels were on the current layer, instead of the layer they're meant to use.I also realised that my current layer was locked (from the previous task).
if the current layer is locked, the contour labels ignore the layer setting that they are meant to use, and come in on the current layer instead. And you can only draw one tangent's worth of contour labels at a time before finishing the command and restarting.
Solution: make a different layer current or unlock your layer.
are contour labels generally created on the current layer and then moved to their proper layer?Is that why it hit a snag: it wasn't permitted to move the object to a different layer because the one it was on was locked?
I am using Photoshop CS2 and whenever I open a .jpg , .gif or use my scanner and scan something into PS the layer always starts out locked.
Is there a way to change this so it is not locked everytime?
I am using Photoshop CS2 with Windows XP. Why are all the photos that I import into Photoshop have the layer locked. I tried to save them both as .psd and as .jpeg. But, it makes no difference. In the layer pallette, the layer is marked as locked but the icons at the top are all grayed out.
View 7 Replies View RelatedI am trying simply to work with layers, however when I start a new document and then import a photo, the background automatically locks. The lock icon is visible in the layers pallate. I can drag that icon to the trash and import another photo but the first photo disapears as the layers all merge on top of one another and the lock icon returns.
View 2 Replies View Related