How to do to cut the selected left line in two to the interception point of the perpendicular line and the left one as quick as possible?
Wish I could have a better way than to trim the bottom part, and draw a new line.
I'm facing a very weird problem with circle and interception osnaps. Maybe I'm wrong, but I've a space between the osnaps interception and the the circle line (pointer) when I'm trying to move it to the bottom or top line.
The problem doesn't occur with line. The osnap will go directly to the interception, but with the circle, I just can't understand... It's currently messing my drawing up, as I'm trying to move the circle tan point to another interception.
Here is the screenshots with only interception snap checked (working in milimeters if it does matter):
Well, seems it does occurs with all the snaps too, tested it with "nearest" too, and look how descaled it is:
What would be the quickest way to rename files in Vault?
I have lets say 100 parts with prefix 1012.
I want to change to 1014.
I can hightlight all parts in Vault, go rename and then replace prefix manually for each part.
Seems hectic.Any quicker, more automatic way?
Adding prefix does not work since does not replaces but adds.
I am new Inventor user (2014 version) trying to get up to speed on best practices and the most efficient work flows. I find myself designing individual parts that start off as base AISC shapes (angles, square tubes, rectangular tubes, etc.). These are parts that start off as base extrusions that then have multiple machining operations performed on them. In most cases, the parts are stand along parts that aren't involved in any type of frame.
In these cases, I generally sketch the profile from scratch using my AISC book and then extrude. I'm sure this is silly. Frame generator already has the profile data built in- so why am I sketching these profiles from scratch? But using frame generator in an assembly environment to make a single member part seems silly to me also. Why should there be an assembly file at all? I just want a single part that starts off as some length of some standard profile. Using frame generator in an assembly environment seems like overkill.
What is the best practice for starting off a part with some length of a standard ANSI, ISO, or other profile?
I have just built a new workstation and I am trying to make sure that I have the optimal settings in Max and the NVIDIA control panel to reduce my rendering times. How to configure optimal set-up for the following workstation. I have tried using both metalray and the advantage pack iray renders. However, when I use the iray it just keeps rendering forever and still looks very noisy or granulated.
System:
Running one Intel 5650 overclocked to 3.4 GHz
EVGA SR-2 Classified MB
(2) Nvidia Quadro 4000 cards
24GB RAM
(2) Crucial 128GB SSD (Raid 0) This is my boot drive
(2) 1 TB WD Caviar Black (Raid 0) for storage
(1) 1 TB WD Caviar Black for backa-up
how to draw a simple fish shape that is consist of an oval with 2 pointed ends (the body), and a triangle (tail)? What kind of tools (eg. line or ellipse tools) should I use? Do I need to set the transformation path?
View 9 Replies View RelatedI do perspective drawing for interior designers and do the coloring in Photoshop. Think of old fashioned painting with a brush/copic marker against a ruler to get a straight line, but with varying thickness or opacity. I would like the same effect in Photoshop.
The closest that I have come is to press Shift before the brush stroke. That constrains the stroke, makes a very neat line AND allows me to vary the line/brush thickness as I paint.
Often the lines may need to be at an arbitrary angle which is NOT 90 or 180 degrees. The only way I know of for getting that brush stroke in the correct position is to make sure that each stroke is on a separate layer. Select the stroke/transform/rotate. Quite a few steps as opposed to the one it takes to draw the line in the correct position and angle with a brush/ copic marker on paper.
This becomes time consuming and difficult once you have many lines to paint and if you need to be accurate (as with perspective drawing). If you are working on a very large canvas the point of rotation can sometimes be very far from where you are working (i.e. on a vanishing point) and difficult to see without a lot of Zooming and moving around on the canvas.
To Stroke a path with the brush gives an unrealistic and even line thickness which does not look hand painted. Using a ruler while drawing on a Cintiq? That may give the desired effect and be much quicker than selecting and rotating.
I was pretty much expecting to see a Ground Plane object in the scene explorer, but no such beast exists. My spirits were briefly lifted by finding a Ground Plane section in the Environments palette, but that does not allow you to attach texture maps to the ground plane, only a solid color.
If such a thing doesn't exist (for shame, Adobe), any quickest way to create a textured, infinite ground plane (imagine, for example, a tiled floor or a wooden floor that extends all the way off into the horizon)?
I have this heavy issue, i can't send to back a line, an object or a hatch under other lines. In 2012 i used this feature a lot but in 2013 it's not working very much, maybe 1 time out of 10 and i absolutely can't say why.
HPDRAWORDER = 1 seems to work with a new hatch.. but i can't redraw everything.
Let's say i put an entire floor plan into block then draw over it. (I don't want to start a Xref discussion please) i can't send the entire bloc to the back.I used to do that with 2012, 2008, 2007.. but it's 2013 it's not working, is there a way to correct that?
The Autocad 2013 x86 or x64 is not installed on Windows 8 Consumer Preview because programs can not read .NET Framework versions 2 and 4 which are integral parts of the OS.
View 5 Replies View RelatedI have 2013 inventor/mechinical a cad did not have enought memory on c: drive added another hard drive E: need to move my files to the e drive. single seat all on this computer.
View 4 Replies View RelatedTrying to change the color of a layer in a viewport (different than the default layer color (i.e. model layer color)). Objects are set to bylayer. Changing the VP color in the layer dialog brings up the color dialog, select a different color, click OK and the VP Color DOESN"T change in the layer dialog. It stays at its previous color. Occurs on several machines.
View 9 Replies View RelatedI recently added 2 monitors to my set up to bring my total to 3. I am trying to figure out the best way to work on one drawing, with 2 differant veiws on each of the 2 main screens.
I would like my main screen to have the plan view and the second monitor to have an isometric veiw (or whatever I need at the time) of the same drawing. Is there a way to have the same drawing opened up in another window, in one session of Autocad 2013. One on the main screen and one on the secondary.
I have a Windows 7 machine running AutoCAD 2013. When trying to open any drawings from our AutoDesk Vault 2013 server, AutoCAD will hard lock/freeze and can only be closed by using Windows Task Manager. When accessing the same files through the Vault first, without opening AutoCAD, they open with no issues.
View 1 Replies View RelatedI’ve just worked on a series of clients drawing using AutoCad 2009. They are using AutoCad 2013. out of 20 or so drawings several drawings when opening with 2013 open up with Errors requesting recovery is required due to any number of errors ranging from 3 to 7 on average. The error message asks [yes] to recover and it aborts or [no] to continue and the drawing opens ok without further error. If I recover the drawings, and save-as 2013 or other, the same errors appear regardless. However if I open the same drawings using my version of 2009, I didn’t get any errors. The original drawings were compatible with 2009 without conversion.
View 3 Replies View RelatedI have been migrating dozens and dozens of .pat files from one version of AutoCAD to the next for many, many versions. Most recently in AutoCAD 2013 the .pat files were stored in the C:Program FilesAutodeskAutoCAD 2013SupportPatterns - worked fine. During the migration to 2014 I received an install error report stating that this subdirectory did not exist and could not be created. Alternately it stated that the new default path C:UsersUsernameAppDataRoamiongAutodesk|AutoCAD 2014R19.1enuSupport will be used instead.
At first I created the Patterns subdirectory where it could not be done automatically. No luck. Then I placed the Patterns subdirectory in C:UsersUsernameAppDataRoamiongAutodesk|AutoCAD 2014R19.1enuSupportPatterns and no luck.
I have an assembly that was created on 64 bit version of Inventor 2013, the total file size of everything is around 150MB. Even if I use 'Pack and Go' to move the file to another computer running the 32 bit version I get an error when I try to open it which says something like:
'unable to allocate 3GB memory for FBAttributeSegment'
The actually figure is over 3GB but of course on a 32 bit version of windows it is physically impossible to allocate that amount of memory (even with the /3GB in boot.ini hack)
I've performed various dynamic simulations as well as animations within the assembly so I'm thinking that perhaps its trying to allocate that huge amount of memory for a saved state of one of those.
What FBAtributeSegment might be and whether there is any special way to save an assembly to avoid this problem? The name FBAttributeSegment doesn't correspond to any part or assembly names.
I should also add that I have no problem opening it in a 32 bit version of Fusion which again suggests to me that it is something like simulation or animation that is causing this
We recently updated all of our software at my company from 2010 architectural desktop to 2013 autocad. We do a lot of architectural work where we use the "wall" functions to draw our floorplans. I have noticed that the walls are disappearing on some files and not on others. Or we will only be able to see the outside line of the wall, but not the interior, which results in an undesirable appearance to the floorplans.
I have also run across these error messages when opening the files, I dont know if they are related or not:
"Unhandled exception C0000005 (access violation reading 0xffffffff) at address E43AA180h"
and
"Unhandled exception C0000005 (access violation reading 0xffffffff) at address D41218AEh"
why when i want to import file sketchup by type "IMPORTSKP" in commadline box, i can't import file sketchup into autocad because AutoCad Error Aborting and fatal error, and after that my autocad suddenly closed by it self, so i can't use my auto cad.
View 3 Replies View RelatedI've made some customisation in the ribbon of a 2013LT version.
Now some customisation functions are only available on the Full, so I download and install it but I can't find a way to import all those custom settings grom LT to Full...
Seems it works only from LT to LT or Full to Full..
Just upgraded a user to Autodesk Building Design Suite Premium 2013 but AutoCad 2013 and AutoCad MEP 2013 are not saving settings.
On first use the crosshair is large and angled, not standard. If I run "Rest values to default" then the settings are standard until I either restart AutoCAD or open a drawing then have the same strange cross hair.
Have tried creating a new profile, setting it as default startup profile by altering the shortcut but no matter what settings are not saved and revert to strange cross hair once AutoCAD is re-opened or a drawing is opening.If logon to computer as a user without a roaming profile all works fine.
We have loaded copies of AutoCAD Architecture 2013 on several workstations. We had tried brining over older profiles (from 2008)- which did not work, so made up new ones. ANYTIME we go into the profile settings to load a different profile beyond the default, AutoCAD Architecture (US Imperial), eventually while working the program will crash. We've wiped out installations of the program, registry and all, and re-installed without brining over any prior data. Same issue.
Even when using a seperate "default" profile us as (Global) or (Metric)- same issues. The problem with staying/modifying the workspace for the US Imperial is it will not load the complete menus with the MENULOAD command (only loads EXPRESS). If we work within the (US Imperial), no crashing, but again, the menus are not available within that profile for some reason, so that is not an acceptable solution.
Happens every year. Upgrade and spend half a day or more trying to get everything back to the way I had it. All I have is a couple small toolbars for commands that are several clicks deep in the ribbons and I want them "right there" all the time.
I thought Autodesk 360 might be a good tool for this. All it did was DOWNLOAD some old settings and destroy one of the toolbars I'd created. They really need an override in there to specify upload, download, overwrite or don't.
I'm trying to migrate (I guess that's the technical term) my settings from 2013 Mechanical to 2014 Mechanical. It's probably too late already, after 360 did its deal, but I really want to get this down so we don't go through it every year anymore.
I maintain that PTC had this part of it down Pro/ENGINEER. You had a config file that was editable plain text.
Infrastructure DSP '14 / Product DSP '14 / Vault Professional 2014
Dell Precision T1650
Windows 7 Professional SP1 64-bit
Intel E3-1270 V2 3.5GHz / 32G RAM
Nvidia Quadro 2000, Driver 331.82
Space Navigator, Driver Version 6.17.7
As many of us seam to do the option to save by default to an older version of AutoCAD or universal DXF format is selected, my problem is however when you save an existing drawing a prompt appears asking if 'Drawing*.dxf last saved in AutoCAD 2004 format. Save in AutoCAD 2013 Drawing format?' this has annoyed me for years!
I have set it as default DXF 2014 for a good reason I don’t want a prompt asking me if I want to then save it as 2013 or I would have set it like that on my default setting, gets on your nerves when you are doing 100's of files.
Win7 64 Pro - Asus P8P67 PRO - i5-2500k CPU O/C@4.5Ghz- OCZ Vertex 2 SSD - 8GB Ram - GTX550 Ti - SpaceExplorer.
Autocad MEP 2013 was working fine until I installed SP1 yesterday.
Now when type in open the dialog comes up (not a filedia issue). When I click the "look in" pull-down in the open dialog it goes blank and I am unable to browse any folders. I've tried rebooting.. Should I reinstall?
how can I develope a proper piping system just like the one in the attached picture in AutoCAD 2013.
As you can see the tubes aren't that greatly connected.
Each tube is blocking the pathway of the other tube.
I need them to be all connected.
The reason why, is because I will be later using this design in Inventor Fusion and Simulation CFD to have fluid in the tubes.
I keep getting that it is loosing connection, so I never really get to download.
View 1 Replies View RelatedWhen customizing the screen menus, adding a few icons or pull down menus, when autocad is restarted, Autocad reverts back to the default menu. How can I set this up to retain any menu changes I make.
View 2 Replies View RelatedAll of a sudden my ribbon panels will not pull off... some refer to this as 'tear off'. The interface is not locked either.
View 5 Replies View RelatedOkay. So our designer is using autocad 2013. He is using a pc and he is sending me the files (i'm on a mac) and the thinest lines do not show or print. But, they print/show on a pc! I need to be able to print these. I've searched the web and found nothing.
View 3 Replies View RelatedAutocad 2013 x64 and DWG TrueView 2013 x64 crash when print on HP LaserJet 5200 (A3)
APPCRASH
acad.exe
25.0.55.0
4f309adb
StackHash_c855
6.1.7601.17725