AutoCAD Inventor :: Error Opening Assembly On 32bit 2013 That Was Created On 64Bit 2013
Oct 2, 2012
I have an assembly that was created on 64 bit version of Inventor 2013, the total file size of everything is around 150MB. Even if I use 'Pack and Go' to move the file to another computer running the 32 bit version I get an error when I try to open it which says something like:
'unable to allocate 3GB memory for FBAttributeSegment'
The actually figure is over 3GB but of course on a 32 bit version of windows it is physically impossible to allocate that amount of memory (even with the /3GB in boot.ini hack)
I've performed various dynamic simulations as well as animations within the assembly so I'm thinking that perhaps its trying to allocate that huge amount of memory for a saved state of one of those.
What FBAtributeSegment might be and whether there is any special way to save an assembly to avoid this problem? The name FBAttributeSegment doesn't correspond to any part or assembly names.
I should also add that I have no problem opening it in a 32 bit version of Fusion which again suggests to me that it is something like simulation or animation that is causing this
Now that we have switched most of our users over to 2013, we are receiving this error - only randomly, not on most drawings - but until it is resolved, we cannot batch plot, publish, because it dumps the plot. Here's a clip of the error we're receiving. When I run a Recover, it doesn't resolve the issue.
I am getting Error Code -6 with both the 64 and 32 bit installers. They install correctly but fail when I run Xara. I uninstalled and used CCcleaner in the middle, and rebooted, and deleted the folder in programdata. I am using Windows 8, Norton IS 2013. XD Pro is running fine.
When AutoCAD is closed and I try to open a drawing from the Windows Explorer I get a fatal error and when AutoCAD is opened before opening the file from Windows Explorer everything works fine. We have this problem with several stations at our office.
I get an error every time I open any drawing after it has been saved in 2013. Opening a dwg that was created in an earlier version does not give the error, but after I save it in 2013, it does.
If I create a new dwg in 2013, save it, close it and then open it I don't get the error the first time. But then if I save that dwg again, I will get it the next time I open it.
The exact error is:
One error was found in the drawing file during open. Would you like to cancel this open?It is recommended you cancel the open and run the RECOVER command on the drawing file.
I run the recover command. It says it found, fixed, and erased 1 error. I save, close, and reopen the drawing and the error still appears every time.
I have 2013 on my system, and it was working fine for a few weeks, but then one day I tried to bring it up and got this error:
[URL]
and when I click on the ok button, it shuts down the CAD window again. I tried repairing teh install, and then I tried reinstalling the program. I still get the same error, no matter what.
Users using Windows 7 -64bit with Architecture 2014
Mapped drives are used for both site to access NAS, but use different drive letters.
At one point working the projects, users starting getting fatal errors opening from the share. All attempts to get past this failed and I thought the drawing or base files were corrrupt. However, when the files are moved locally to workstation and opened without issue. The users in one office are now working off this files using UNC \serverproject...
The interesting thing, is that users in the other office have no issues dealing with these drawings using on the NAS. The only difference is the WAN and drive mapping letter. This is how they have always worked and never had this issue. The only other thing I will add is they upgraded from 2010 two months ago, but no problems with any other projects.
I have been using Inventor 2013 for a few weeks now and for the life of me I can not work out how to turn off the automatic "Edit dimension when created" .
I do know that there are "Edit dimension when created" checkboxes in both the Edit Dimension window and under Application Options. But everytime I restart Inventor, the program seems to forget that particular custom setting and always switches "Edit dimension when created" back on. So that on the first dimension I create, the Edit Dimension window pops up.
For additional info Inventor remembers many of the other custom settings (e.g. compact tool bar, active button on the Quick Access Toolbar, etc...)
We recently updated all of our software at my company from 2010 architectural desktop to 2013 autocad. We do a lot of architectural work where we use the "wall" functions to draw our floorplans. I have noticed that the walls are disappearing on some files and not on others. Or we will only be able to see the outside line of the wall, but not the interior, which results in an undesirable appearance to the floorplans.
I have also run across these error messages when opening the files, I dont know if they are related or not:
"Unhandled exception C0000005 (access violation reading 0xffffffff) at address E43AA180h"
and
"Unhandled exception C0000005 (access violation reading 0xffffffff) at address D41218AEh"
We have found that after installing SP1 for Inventor 2013 is nearly impossible edit derived assembly. It takes very long time for open dialog of Derived assembly, without SP1 it takes approx. 2mins. for assembly of 20000 instances, with SP1 it takes more than 2 hours! This we are able to reproduce on each of our station. And more, there is still not corrected bug with save setting of hole patching range. This setting does not remember min and max value and after re open this dialog the range is set back to default value 10-9999mm.
I have tried ti disable antivir and all unnecessary services - no effect.
Inventor 2013SP1, Win7SP1 64bit, Eset Endpoint Antivirus 5.0.2126
When I try to open help in Inventor 2013, I get the error shown below about internet access.So I downloaded the offline files and saved them to C:program filesautodeskinventor 2013 and double clicked on the tutorial_files.ipj file to open Inventor as instructed in the installation notes, but still get the error. I opened the HelpIds.xml file in the Inventor Bin folder and set Use Online="0" and also copied another set of files into c: programs autodesk inventor2013local help and double clicked the tutorial_files.ipj file located there.
file was working fine until about the last large componet i am working on.
when I edit a part and then hit return the ("excuting end edit componet " in lower left hand ) it seems to take some time to compute. This part i have a lot of sketches that are tide to other componets to create the postion of those. so i think this is the reason. i supressed this compent and the file got about 75% better so I am thinking that this is my issue.
for example when i need to make a cut out in one compent that is overlaying another I create a construction projection of the componet and then use this to off set or create a feature from that so that if I change the other one it changes the cut out. I am thinking the computer is having to figure out what is changing everytime.
One of our customer has inventor 2013 and I am working with inventor 2014.
I would like to know if there is anyway for my customer once my job is done to be able to load the Sub assembly with his software and be able to work with it ?
They told me Inventor fusion is not an easy tool and would prefered to use inventor files.
why when i want to import file sketchup by type "IMPORTSKP" in commadline box, i can't import file sketchup into autocad because AutoCad Error Aborting and fatal error, and after that my autocad suddenly closed by it self, so i can't use my auto cad.
About three days ago Inventor 2013 started crashing whenever I tried to drag a subassembly into position. I got a message telling me to install SP1. I did this; but the crashing continues to occur. I can use assembly constraints to move my subassembly around but this is cumbersome.
when trying to reopen a file from the "recently used" file list? When I try to click on a file from the list it gives me a message stating "error opening file". I know this will happen if the file has been moved to another location, but the files are in the same place as when I originally opened them. None of the files in the list will open anymore. Is this a pathing issue?
In ACAD 2013, everytime I try to sync my settings to "the cloud", the pull down menu reads "Customization Syn - Error". I am signed in OK to Autodesk 360. Stand alone 64 bit installation on a single machine.
I could not print, save, make any changes to one particular drawing which was created ion Autocad 2013. Whenever I tried to work on the file attached error message pops up and Autocad program gets closed.
i get the following error msg "an autodesk product failed to send the required value for UPITOKEN. the error report sent to autodesk may be incomplete." and then another one also come "FATAL ERROR: unhandled e06d7363h exception at 75b19617h". then finally close.
When I search in content explorer it work just fine but when I click on a drawing to open it acts like its opening but right at the end it says Error Decrypting Data and wont open I've tried to look for a solution and I cant find anything.
I have a customer who uses Solid Works and I of course have Inventor 2013. Before I get into discussion with them about software compatability I wanted to ask the experts! Can I open Solid Works drawings with Inventor?
I have this assembly. I want to sort the browser, so I go to Assembly Tab, Productivity panel, Alpha Sort Component. a few seconds later, I get "Sort Failed". I am not in a weldment, not in locked view rep.
I am currently working on a school group project that requires me to submit all inventor files as "LASTNAME_FIRSTNAME_PART,ASSY,DRAWING,etc..NAME". My original parts were all done in mm instead of cm, so for our project, I opened all new files and derived the same parts at a different scale to fix this scale issue between the members. For the new derived parts I temporarily allowed the file name to remain as part1, part2, part3.... and continued with the assembly. Now that my assembly is complete and I would like to change my part file names to the required format, my assembly will not show the parts and (?) symbol is shown by all parts with updated file names. I also changed the original file names and now the new derived parts, when opened, have the same (?) which I assume is related to the fact that the derived parts are dependent on the original file. Is there a way to update this information? We are using INVENTOR 2013.
In Inventor 2012 user has ability to change the material properties globally.
All parts using certain material will follow the changes made to properties and written to single library. It is clear and predictable.
In Inventor 2013 material properties belong to individual file.
When changes were done to appearance properties of a single part there could be situation when the same material parts in the assembly could have different appearance.
Here is the fact I do not understand and it is contradict to actual reality since the same material with the same standard must look absolutelly the same when switched to Master view.
Seems like to make parts look the same or to change the appearance I should click on each single file and make the same changes to each file.
I do not intend to change the appereance properties in single file on purpose to make problems to myself but I am sure I will take somebody else part and it will be changed due unnecessary reflection or other too much realistic things added in 2013. So finally I will get some sort of parrot collored assembly without clear and most importand easy way to make an order.
So I wish I could equalize all same material parts in apearance view. I do not count the way of clicking each file.
So I created the rail sub assembly everything looks great in sub assembly composer.
Start a new dwg data reference in the rail alignment, Note the rail alignment type is set to rail.
Create an assembly and under the Construction tab for the assembly the Assembly Type is set to Railway. Attach my custom sub assembly to this assembly.
Created a corridor and I get this error: Something wrong with current subassembly: Operation is not valid due to the current state of the object.
So I delete my sub assembly attach the Civil 3D Rail Single sub assembly. Re run corridor and everything works fine.
So I promote the alignment change type to centerline. Delete the Rail Single sub assembly put my rail sub assembly back. Rerun the corridor and everything works.
So then I undo everything up to the point of promoting the alignment.
Opened the base file changed the alignment type to centerline.
When I tried to synchronize the references I ended up a broken reference with the following error. Invalid reference. Synchronization failed
Not good we already have plan sheets cut.
where in sub assembly composer were do I define the sub assembly to be for Rail?
I'm using Maya 2013 SP2 on a MacBook Pro running 19.8.2. When trying to load 32-bit floating point OpenEXR or Tiff files for displacement maps I will invariably get the following error:
// Warning: Failed to open texture file: <file path>
The proper OpenEXRLoader and tiffFloatReader bundles are loaded in the Plug-in Manager and the very same files open without issue on Maya 2013 on my Win7 machine. It seems this is OSX specific.
