I could not print, save, make any changes to one particular drawing which was created ion Autocad 2013. Whenever I tried to work on the file attached error message pops up and Autocad program gets closed.
View 7 RepliesOkay. So our designer is using autocad 2013. He is using a pc and he is sending me the files (i'm on a mac) and the thinest lines do not show or print. But, they print/show on a pc! I need to be able to print these. I've searched the web and found nothing.
View 3 Replies View RelatedAutocad 2013 x64 and DWG TrueView 2013 x64 crash when print on HP LaserJet 5200 (A3)
APPCRASH
acad.exe
25.0.55.0
4f309adb
StackHash_c855
6.1.7601.17725
I have an assembly that was created on 64 bit version of Inventor 2013, the total file size of everything is around 150MB. Even if I use 'Pack and Go' to move the file to another computer running the 32 bit version I get an error when I try to open it which says something like:
'unable to allocate 3GB memory for FBAttributeSegment'
The actually figure is over 3GB but of course on a 32 bit version of windows it is physically impossible to allocate that amount of memory (even with the /3GB in boot.ini hack)
I've performed various dynamic simulations as well as animations within the assembly so I'm thinking that perhaps its trying to allocate that huge amount of memory for a saved state of one of those.
What FBAtributeSegment might be and whether there is any special way to save an assembly to avoid this problem? The name FBAttributeSegment doesn't correspond to any part or assembly names.
I should also add that I have no problem opening it in a 32 bit version of Fusion which again suggests to me that it is something like simulation or animation that is causing this
I’ve just worked on a series of clients drawing using AutoCad 2009. They are using AutoCad 2013. out of 20 or so drawings several drawings when opening with 2013 open up with Errors requesting recovery is required due to any number of errors ranging from 3 to 7 on average. The error message asks [yes] to recover and it aborts or [no] to continue and the drawing opens ok without further error. If I recover the drawings, and save-as 2013 or other, the same errors appear regardless. However if I open the same drawings using my version of 2009, I didn’t get any errors. The original drawings were compatible with 2009 without conversion.
View 3 Replies View Relatedwhy when i want to import file sketchup by type "IMPORTSKP" in commadline box, i can't import file sketchup into autocad because AutoCad Error Aborting and fatal error, and after that my autocad suddenly closed by it self, so i can't use my auto cad.
View 3 Replies View RelatedAs many of us seam to do the option to save by default to an older version of AutoCAD or universal DXF format is selected, my problem is however when you save an existing drawing a prompt appears asking if 'Drawing*.dxf last saved in AutoCAD 2004 format. Save in AutoCAD 2013 Drawing format?' this has annoyed me for years!
I have set it as default DXF 2014 for a good reason I don’t want a prompt asking me if I want to then save it as 2013 or I would have set it like that on my default setting, gets on your nerves when you are doing 100's of files.
Win7 64 Pro - Asus P8P67 PRO - i5-2500k CPU O/C@4.5Ghz- OCZ Vertex 2 SSD - 8GB Ram - GTX550 Ti - SpaceExplorer.
In ACAD 2013, everytime I try to sync my settings to "the cloud", the pull down menu reads "Customization Syn - Error". I am signed in OK to Autodesk 360. Stand alone 64 bit installation on a single machine.
View 2 Replies View Relatedi get the following error msg "an autodesk product failed to send the required value for UPITOKEN. the error report sent to autodesk may be incomplete." and then another one also come "FATAL ERROR: unhandled e06d7363h exception at 75b19617h". then finally close.
View 3 Replies View RelatedWhen I search in content explorer it work just fine but when I click on a drawing to open it acts like its opening but right at the end it says Error Decrypting Data and wont open I've tried to look for a solution and I cant find anything.
View 6 Replies View RelatedNow that we have switched most of our users over to 2013, we are receiving this error - only randomly, not on most drawings - but until it is resolved, we cannot batch plot, publish, because it dumps the plot. Here's a clip of the error we're receiving. When I run a Recover, it doesn't resolve the issue.
View 6 Replies View RelatedI use autocad architecture 2013 and it works just fine until the save turns to qsave whenever i want to save a drawing by save, save as and ctrl+s it works as qsave..how can I turn it back to SAVE ?
View 9 Replies View Relatedi am using autocad 2013 student version at home and at college i am using autocad 2012. so when i create drawing in 2013,dosent open on 2012"it says incompatible version". i like to save all my dwg files automatically in 2011 format, i dont want to click save as and change it 2011 format.what i need is whenever i finsh working on drawing, if click save it should automatically save in 2011 format.
View 2 Replies View RelatedI just downloaded and installed Infrastructure Design Suite Premium which includes AutoCAD 2013. For some reason the PDF drivers are not working, and I have already gone through the add a plotter wizard to no avail. One thing to note is I still have AutoCAD LT 2010 on my machine, and all the print drivers work fine for it. Perhaps there is some kind of conflict between the two CAD programs on one machine?
View 9 Replies View RelatedHow can i insert a JPG that will print?
I'm using the Insert > Reference > Attach command but the image in the JPG does not print.
How can i adjust the area I want to print? I mean the dashed line. What i need to do is print out a map and i want it to cover the entire paper, without any bords around it.
View 5 Replies View RelatedI have autocad 2013 student version installed on a MacBook Pro with OSX mountain lion, worked properly, but now I can not print anything in paper, pdf, or preview. I just try re-installing the software, creating new layout, select the printer from "Edit page setup" menu, without any results.
View 2 Replies View RelatedIs there a way to have only part of the text in a multileader highlighted for printing out?
View 1 Replies View RelatedWe are in the process of upgrading from AutoCAD 2010 to 2013. The print screen key on the keyboard will not work in the 2013 version (using Snagit to capture the screen image). Changing the hot key (in Snagit) works but I'm trying to keep the same workflow for my 300 plus Users.
View 2 Replies View RelatedI'm trying to print a 2D drawing but I would like to add the 3D solid for viewing reference. I can't seem to "flip/rotate" my 3D solid to obtain an isometric view while looking at my 2D drawing from the top view.
how I can get both items to print on a single plot?
I work for a home builder and I receive the drawings in autocad format. Each house drawing comes in autocad but each floor plan and elevation is represented by a "layer state".
Each of these drawings has 7 to 9 pages and when I want to print each of those pages, I have to do it "one by one" as I have to switch between layer states.
So, each file has a layer state for: basement plan, main floor, second floor, etc. I want to find a way that I can print (convert to pdf), all these drawings, rather than going by each "layer state"
I received a layout of a building from a architect. When I try to print it out it is extreemly light. This happens no mater what printer or ploter I use. I have changed line weight with no success.
It seems to always happen when I get a building drawing from an arhitect.
Even the new items I have drawn like conveyors , tables stc. come out nearly invisable.
I need to convert a Cad file into a PDF file. Unfortunately, the PDF file won't print. The first time I had this problem was I converted it with the layers on the PDF file. What I did last time was this:
-I went under Plot-Model
-Under the Printer/plotter, I clicked DWG to PDF.pc3 and click on Properties
-Click under the Device and Document Settings tab
-Click on Custom Properties
-Click on Custom Properties buttom
-Under the DWG to PDF PRoperties table, I click on Capture all under Fon Handling
-I uncheck Include Layer information under Additonal Output Setting
-I click ok
When I begin to plot under Batch Plot, I also went and click on Publish Options, and on that table under Layer information, I click on Don't include.
For some reason, it's not printing the way as it should. I don't know what other option I have in order the print corretly.
Having issues using the accoreconsole.exe, to batch plot drawing to pdf?
none of our embedded images/logos get plotted. im guessing it doesn't support images yet.
i was excited about this addition (it would save me hours a week), but not anymore back to the publisher we go
I have a CAD dwg with an embedded OLE object (Microsoft Excel). I am able to edit the text with no problems, but I am not able to resize the viewing window in CAD.
I have reset the 'print view' in Excel several times, hoping that this would render the problem. However, it is still showing 1 row of extra cells that I do not want to see.
im trying to do is print on standard 8.5" X 11" paper but for some reason it keeps cutting off the top and the bottom. ive tried changing the plotter settings around but to no avail. its like theres a certain amount that it refuses to pring on the bottom. no matter what, the is always a .5" gap at the bottom. i can get it to print to the very edge of the top. just having issues with the bottom. ive also tried using plot calibration and all of that is fine
See photo for what im getting. and yes its doing it when i make pdf's too.
I need to print out a map the actual dimensions of the map are 36x65. For some reason, btw this has worked in the past. I have tried all the troubleshootings i can think of like, printing from a new project with default settings, printing from the view ports, even in the model worksheet. I tried making the paper size longer, i have tried window, limit, everything. But for all the reason i can not understand it always just plots exactly at 36 x55.. i have plotted things that are 36 x 80+ so i know i don't have a length limit.
View 3 Replies View Relatedwhile in a layout tab in paperspace, if I zoom in and try to plot a windowed area, the feature layer information does not print but all vector information does. If I zoom extents and replot using the same previous settings with the small windowed area, all layers plot like they are supposed to. Now another scenario is as follows:
View 2 Replies View RelatedIn ACAD 2007 when I create a new UCS, the dialog box shows as current an unnamed UCS which I can then rename. In 2014, this doesn't happen - I have to do all that using the command line. Is there some setting to get the dialog box to work?
View 7 Replies View RelatedI can't print my drawings in PDF with format A2, A1, A0 in landscape with good orientation (A3 is ok). The attachment file "ScreenShot-A1" is the only correct pdf but oriented in portrait.
If I print with landscape orientation (preview on Autocad is good), I get the pdf file "Document-A1".
Note: We can't use DwgToPdf due to problem lines which disappeared or moved with different versions of Adobe Reader.
My company imposed PdfCreator V1.2.2.
I have a Hatch in my drawing with Pattern as Solid on the top of an image. I made it transparent and it looks really nice in my screen, but as soon as I print either in PDF or hard copy the transparency feature disappear. How is possible to print my Hatch -with Solid as Pattern- with the transparency active either in PDF and hard copy?
View 3 Replies View Related