Is there any way to have 3d polylines show a linetype? I need to have my contours that are created as a 3d polyline show up as a hidden linetype. These polylines came from an aerial mapping and have lots of vertices.
View 5 RepliesMy custom linetype (something like this ----W----W----W----W---- ) doesn't work as a huge polyline (6 units wide.) The line is wide enough but the letters are tiny dots.
If I try to set the lineweight by layer, the maximum is 2.11 mm, which is way too small for the 50" by 70" map I'm working on.
Is there a way to get a nice looking line that wide with letters ( ----W---- for water, -----S---- for sewer, etc.) or should I tell my boss that we have to use the standard lines?
As the above mentioned, I have a drawing drawn using polylines with width from someone. The width of the line are suppose to represent area,
To put things into prospective, here is an example:
The polyline is 10 unit long and with a width of 2 unit wide. If i explode that polyline, it will become a single polyline without width. The line are suppose to represent 10 unit long and 2 unit wide; representing an area.
My question is is there a way to change the line above directly from polyline with width to a close polyline (4 x polylines) of 10 unit long and 2 unit wide.
Today I noticed 6 or 7 linetypes that have appeared in every drawing I open and cannot be deleted.
They include "Amzigzag" " Amconstr" "ACISOTGB" and others.
If I delete everytjing in my drawing and purge the linetypes are still there. They even appear if I load old drawings that din't have these linetypes initially.
Inventor 2013
For some reason all of my linetypes have disappeared, and even when I go to Load, there are no options. The only linetypes available are lines and dashed lines, and I have a fence linetype but it does not show the circular pattern in the fence. How can I get these back?
View 1 Replies View RelatedOk over the years here they currentley have lots of differnt custom linetypes scattered over lots of drawings. What I am trying to achieve is to drive some standardization here
So what i want to do is create a series of standard drawings with various custom linetypes
So using design centre i can drag and drop linetypes into a standard drawing but what i really want to do is export these custom linetypes into a .lin file
is it possible to do this ?
I have a drawing that have blocks in them I cant find inserted. I cant purge them or the linetypes they have. How do I strip them out if I cant find them to explode them?
I have attached the file.
Is there a way to change linetypes within a certain object?
EXAMPLE:
I want to show hidden lines under another object.
So far, what I do is trim the existing lines and draw new ones with a new layer.
I need to create a complex linetype for a fence. The line needs to consist of the following:
------X------X------X----- The linetype needs to be dynamic to any length.
How do I remove unused linetypes from drawing
View 3 Replies View RelatedIf I start autocad and draw a line then change its linetype from continuous to Fenceline2 it shows up like it's supposed to, a line with small squares in it. I can also change it's linetype to Fenceline1 and the linetype shows up just fine with the line and small circles in it.
But when I call up some existing autocad drawings that have lines with the Fenceline1 or Fenceline2 linetypes assigned to them, the small boxes or circles are missing from the linetypes. When you type linetype at the command prompt the linetypes are listed in the dialog box, but for some reason they are not showing up right in the existing drawing. When I type linetype, and hit the load button, and browse to my acad.lin file and select it, I get an error message of Bad Definition for linetype Fenceline1 and another for Fenceline2 and another for Batting etc.
So why are these Complex linetypes not working in the Existing drawing but work fine in the just call up autocad empty drawing, and how do I fix them to work in the existing drawing?
We recieved some drawings from a client for updating. The Pneumatic, System Link and Heat Trace lines all show up solid in the drawings when I open them up in AutoCAD 2012. We tried opening them in AutoCAD 2004 and are experiencing the same issue. In the Linetype Manager menu, under Description, the linetypes appear correct. Under Appearance, Heat Trace and Pneumatic appear solid and System Link appears dashed (just as they do in the drawing itself).
Here's the kicker. A co-worker has AutoCAD 2004 on his laptop and everything shows up and plots out just fine.
I can not get certain linetypes to start with the same dash length, see attached. The linetype will start with a longer dash then the stated length, depending on the length of the pline segment. Is there a way to fix this?
Here is the code for one of the linetypes highlighted:
*FENCELINEc,EX FENCE X---X---X---X---X---X---X--
A,.125,-.0625,.125,-.0625,.125,-.0625,.125,-.125,[FENCEx,FENCEx.shx,x=-.025,s=.1],-.0625
We have a problem in our office. In some of our drawings we keep getting a lot of unwanted linetypes and text styles. Nobody is sure where they originated.
We have tried this method in getting rid of them but it doesnt work. [URL]
See attached file.
Same applies with the text styles.
I created some custom linetypes. When I copied them over to my drawing, the text in the linetypes came in extemely large. I really need to get this figured out as I am setting up a template for a new customer, and they want all these included.
I have attached the dwg for reference.
I have drawings at the moment where I need to convert some lines to polylines. I know you can use PEDIT and PEDITACCEPT=1 but i want to match properties at the same time.
Just wondering if there is a comand or lisp routine that duplicates the MATCHPROPERTIES command but converts lines to plolylines at the same time, this way all i would need to do is type in the appropriate command and select my source polyline and get multiple duplicate polylines by clicking the lines I wish to change?
I have a contour set created using polylines and I want to convert this to points. Can I do this in AutoCad 3D Map?
View 3 Replies View RelatedI'm trying to create a 3D solid from four 3d polylines that represent a bridge deck .
If it is not possible to create a 3D solid, can i create a surface?
why I cannot join the various polylines in the attached example? My objective is to create 2 closed polylines, Line 1 and Line 2.
View 1 Replies View RelatedHow do I transfer 3d polylines from civil 3d 2010 to 2004?
View 2 Replies View RelatedWhenever I select a block or polyline in 2012, the program hangs for about 1 minute. This never happens when using 2010 on the same system. Obviously this can't continue.
View 3 Replies View RelatedIs there a way that I can add multiple polylines in feet and inches? I downloaded some lisp routines, but they are not in feet and inches.
View 2 Replies View RelatedIn 2007, I was able to select multiple polylines before typeing in PEDIT. When I was done with the command, I could then type in PEDIT and L for last and it would select the multiple polylines I had first selected. We just got 2012, and when I do L now it just selects one line. Can I change this?
View 7 Replies View RelatedI have several days of experience with Autocad 2010... The problem: I have many (a lot) polylines in my 2D drawing that are adjacent to each other, but not joined. What is a good way of joining them, so that those that "touch" each other become one? Maybe I can hatch the area, then delete polylines and then reconstruct the boundary?
View 9 Replies View RelatedHow to draw 3D polylines, or convert single lines to polylines?
this.JPG
In 2008, never had this issue.Just dumb, circles, and lines in a view port, that have hidden or center linetyoes assigned to them. When we go to plot using legacy hidden (this new for 2012?) the plot comes out with continuous lines. These are not solids. Just ordinary line entities.Now, when I change the shadeplot to "hidden" the linetype is shown correctly, but now my entities are coloured, when I just want my drawing to be black and white (going to PDF), even though all of the colours in the pen style are set to "Black".
Has this changed? Is there a new variable introduced?
Is there a way of converting 3d polylines to polylines with an elevation?
I have a dwg of contour information, the contours are 3d polylines, because they are contours the z value is constant all along the line, so there no question what the elevation of the polyline would need to be.
I need to do this as I then need to import the dwg into a GIS programme called MapInfo whch doesn't read 3d polylines.
I have access to AutoCAD 2004 or 2005LT.
How can I purge linetypes? We get data from outside sources and my goal is to load our linetypes. I have a list of layers and store the previous layer linetypes. I reset them all to "Continuous". Now I have to purge the old linetype definitions but I can't make them go away. I need to purge DASHED and HIDDEN so far. If I open the file and click on the linetype in layer manager, I still see the old DASHED and HIDDEN definitions. I have tried db.purge(linetypeobjectid) but they don't go away.
Do I need to go through the symboltablerecord to find the correct linetypetablerecord and remove it? Will that remove the linetype from the list shown in layer manager? That is what I need to do - make sure DASHED and HIDDEN *have* to be re-loaded from our linetypes.
I can actually purge these hidden line types.
The line types in question are funky looking line types that do not exist within our office. They often contain "$$" and and/or file names and other odd characters as if they are remnants of binding a drawing. In any case, they are not visible anywhere in the drawing. We refer to these drawings as being "infected".
If any object, i.e. block, text or even a simple line, is copied from an infected drawing into an uninfected drawing, all of the mysterious line types follow. And when I say all, I mean 50+. Furthermore, copying from one infected to another infected will double the line types. So, as you can see, if undetected, you could easily have 100's of "line types" on a drawing which substantially increases the size of the .dwg file.
The process that I have created (from researching on the internet) is to save the .dwg into a .dxf. Close the .dxf and then PURGE. Purging the .dwg will not work. And, you MUST close and re-open the created .dxf in order to purge these files. The you can again save as a .dwg. To complicate things, occasionally a .dwg will not save as a .dxf unless I AUDIT it first.
Needless to say, this is a giant pain in that the files that are infected are at least 50 in number. I have created a macro or two to at least reduce some of the steps. Unfortunately, since the .dxf must be closed and re-opened (which cannot be done in a macro) an all encompassing macro cannot be written.
In one viewport i have a contour drawn as a dashed line. to show the item is hidden.In Another viewport i freeze all layers 'above' this item leaving only the item in the dashed line. is is possible, without copying the line to have the line come through in the later viewport as a continuous line, but remain in the first viewport as dashed?
View 1 Replies View RelatedNeed some customized linetypes for RW, PL, and so on that I can use?
View 9 Replies View Related