AutoCad :: How To Suppress Suffix For Angular Dimensions
Sep 27, 2011
I'm having trouble displaying the units for dimensions. The issue is with the suffix.
When I add the " suffix to indicate inches autocad also adds the suffix to the angular dimension.
2 questions...
Is there a way to suppress the suffix for angular dimensions? Do I need to have a dimension style just for angular dimension?
I do not want to dimension in architectural because I don't want the dimensions to change to feet and inches.
View 4 Replies
ADVERTISEMENT
Oct 3, 2012
Is it possible to have text below the angular dimension line like you can with most other dimensions. The attached pic shows my 10 dimension with the type. Under the line and my 30 dimension with type. Under the line but the type. Under the 30 is just a text box I eye-balled in to place it is not attached to the dimension. I looked in the styles editor but could not find the setup option I need.
View 8 Replies
View Related
Jun 25, 2013
Cannot find a way to set up angular dimensions to show that first zero if the minutes or seconds value is less than ten.
Desired: <degrees>08'05"
Stuck with: <degrees>8'5"
View 1 Replies
View Related
May 14, 2012
how to sensibly extract angular dimensions as attributes.
I can extract the attributes from a block containing angular dimensions, the attributes list angular dimensions as a field but don't actually list the number of degrees for the angular dimension.
It is the number of degrees that I am actually trying to obtain - but I cannot work out how to obtain the information
View 3 Replies
View Related
Sep 24, 2013
I am trying to create a lisp file to automate the placing of angular dimensions at all of the vertex's along a very long polyline. There are 500-600 nodes at least and we need the angle between the incoming and outgoing lines at every node.
Is there a way to automate this with a lisp file, or am i relegated to clicking 1800 times and waste 3-4 hours doing this?
We get these files quite often and this will be a huge benefit to us.
View 5 Replies
View Related
Nov 12, 2012
Is it possible to suppress alternate dimensions below a certain value? I would like my dimensioning to be set up as follows.....
everything above 8 feet
97 1/2" [8'-1 1/2"]
everything below 8 feet
94 3/4"
View 1 Replies
View Related
Sep 16, 2011
I am using AutoCAD 2011. When I create a radius dimension on the inside of an arc, and I place the dimension beyond the center point of the arc, AutoCAD automatically draws an extension to the arc and points my radius dimension leader to the outside of this extension, rather than to the inside of the original arc.
I don't really like this. I prefer for my demension leader to point to the inside of the original arc. I can get exactly what I want by going into "Properties" for the radius dimension and turning the "Ext Line" property off.
Rather than having to do this every time, I'd like to create a dimension style that would give me this functionality all of the time. When I try to modify my dimension style, I see that there are just two parameters for Suppress Ext Line 1 and Suppress Ext Line 2. These seem to apply to both linear dimensions and radial dimensions. Is there anything I can do to suppress the extension line for radial dimensions only and not linear dimensions?
View 6 Replies
View Related
Apr 11, 2011
what the command for Dim Suffix? I wanted to add "m" in my dimension text but i need the command because i am using it for a script file.
View 3 Replies
View Related
Nov 6, 2013
This happened in the middle of dimensioning A drawing. Was adding tolerance and some text to some dimensions which usually looks like this.
1.500±.001" Turn Runner
But all of a sudden it started to look like this.
1.500" Turn Runner±.001" Turn Runner
Everything in the dim suffix field is repeated twice and I don't know why.
No variables were changed...I literally did one dimension that came out normally and the next one did this.
Now all dimensions do this. There is a single dimstyle with no daughter styles.
View 9 Replies
View Related
Dec 13, 2012
If you can make lisp for angular dimension when i have profiles x scale 1-500 and y scale 1-50 and i want when draw angular dimension take scale 1:1 x & y.
View 2 Replies
View Related
Oct 2, 2012
I have set up a dimension style in vb .net, I am having rouble setting the suffix and the linear precision? Here is what I currently have:
Dim acDimStyleTbl As DimStyleTable
acDimStyleTbl = acTrans.GetObject(acCurDb.DimStyleTableId, _ OpenMode.ForRead)
Dim sDimStyleName As String = "test"
Dim acDimStyleTblRec As DimStyleTableRecord = New DimStyleTableRecord()
[code]....
I need to add a single quotation mark for the suffix ( " ie: inches ) and I want the precision at '.00'.
View 2 Replies
View Related
Aug 7, 2009
In the dimension styles we have linear suffix and angular suffix. For angular dimensions we just want the degree symbol and for the Linear suffix we want the foot symbol. But when we dimension an angle we get both degree and a foot symbol, and we just want the degree symbol. We put the foot symbol on the linear units only yet it shows up on the angular dimensions.
View 5 Replies
View Related
Oct 21, 2013
why after selecting Dimension, Angular, then selecting two lines, I do not get the angle between them? I am using v 2000 if it matters. I enclose a screen shot of the two lines I need the angle of.
View 9 Replies
View Related
Nov 14, 2011
im using IV 2011 RS, the spacing of my suffix is like double spaced it looks like 15 " and i want them to look like 15"
View 1 Replies
View Related
Sep 16, 2013
why my dimstyle appears different when I use different versions of AutoCAD.
In LT it is correct (left hand image), both styles are STANDARD font but in the full version (right hand image) the suffix text style is ROMANS.
View 6 Replies
View Related
Apr 26, 2012
I am using a dimension style that annoyingly adds the number "1/8" at the end of every angular dimension. Linear dimensions are fine.
I already checked and there is no suffix specified in the style. I also tried the dim/up feature, but the "1/8" still appears.
Degrees in "Units" are set to decimal. They are also set in decimal within the dimstyle.
Just to clarify, the number "1/8" is added after the actual dimension. I drew a 90 deg rectangle and the dim shows 90 1/8.
I could certainly try to create a new dimstyle from scrap, but perhaps any better tip.
View 4 Replies
View Related
Mar 21, 2013
Why does my angular dimension have a straight dimension line instead of curved?
View 4 Replies
View Related
Jan 17, 2013
How do i get the leading zero to show on an angular dimension for the seconds? as in: 108d 36' 03" ?
View 1 Replies
View Related
May 13, 2013
What is the best way to measure angular displacement on a FEA simulation?
A simple example is described here: The screen shot shows a long rigid body (left) mounted on a bracket (far right). The legs of the bracket are fixed on the right. There is a down force on the left. The goal is to measure vertical displacement on the left. All of the vertical displacement comes from flexing at the bracket, so this can be considered an angular displacement.
Is there a way to measure this vertical displacement without the long rigid body or it's mesh elements?
Or is there a way to turn off the mesh elements on the rigid body? I want to eliminate the unnecessary FEA computations to speedup the simulations.
View 4 Replies
View Related
Oct 30, 2012
I am looking for a lisp routine or rename mulitple blocks by keeping the same name, but adding a suffix to it.
I have used "rename" block to add a prefix to multiple drawings, but it doesnt let you add a suffix. (As far as I can see)
View 7 Replies
View Related
Oct 20, 2011
Is there any way possible to have an angular dimension to denote an angle of greater than 180 degrees?
View 4 Replies
View Related
Sep 9, 2012
is there any way I can place dimension on drawing that would be in dual units (in decimal degrees and in deg min sec)?
I did not find this possible so far.
View 2 Replies
View Related
Oct 29, 2012
I have a 2D drawing that I used presspull to give the correct depth to. Now I have to make modifications to it that are angular to the presspull direction and am not sure that presspull is the correct way to do it. I've searched around for vids and have looked at quite a few, but am stumped. Don't know if I need to change the orientation so that the angle I want to cut is the direction for presspull or if I am simply looking at the problem wrong. If I knew how to take a screenshot, I would post some so that it would be clear how inept I am.
View 6 Replies
View Related
May 3, 2013
Why the lines sometimes get angular when I draw a circle/curve? How can I make them round?
View 8 Replies
View Related
Oct 28, 2003
I am wondering if it is normal for the lines to be jagged. Vertical and horizontal lines are straight but the angular ones are jagged, Stair step looking whatever you would call it. It makes the stuff I draw look like (edited) .Especially the low angle stuff.
View 9 Replies
View Related
Dec 17, 2012
We are projecting a support for one mirror of our Infrared beam line. The support is a block with a rotational weak link and that needs to be rotated about +/- 1°. I would like to know a way to insert this angular displacement and get the stress in the weak link area. I don't have the moment loads and components.
View 1 Replies
View Related
Nov 11, 2011
I currently have a LISP routine that will replace the value of a specific attribute name with sequential numbers in the order that the blocks are selected. Like TCOUNT for attributes - and it only looks for a specific attribute Tag Name called "ID".
However, what I want it to do now, instead of just putting the number into the attribute value, I want the number to be a suffix to the existing default tag value of the tag named "ID" which is "ADDRESS:" for some blocks and "ELEVATION:" for other blocks but the tag name that the routine always has to filter for is "ID". That way the user can pick anywhere on the block - not being forced to pick the tag we want to add numbers to.
What I need the new LISP to do is append a space and then a number to the existing tag value in the block, so that the result would look like "ADDRESS: 1", "ADDRESS: 2", "ADDRESS 3" or "ELEVATION: 1", ELEVATION: 2", etc. depending on whatever the default value for the tag "ID" is.
there are several hundred different block names - but they all have a Tag Name of "ID" - whose default value is sometimes "ADDRESS:" and sometimes "ELEVATION:".
View 8 Replies
View Related
Sep 5, 2013
I have a block of a guide sign with directions and azimuth angles. I made arrows rotatable and angles were changing ok. But when I try to rotate an arrow into zero position, dimension shows 180. I need the dimension to show 0 degree. How can I do it?
And I can’t make angular dimension show degrees greater than 180 even if I specify vertex – after rotation angle shifts on the other side. I gave up and used back azimuth.
And I can't make an attachment: "The contents of the attachment doesn't match its file type"?
View 2 Replies
View Related
Mar 26, 2012
I am trying to put an angular dimension from a hole to a slot positioned planes 90degrees to each other. How can I achieve this? Typically, it depends on how it is put into the ipt file but I didn't know how else to put the slot in therefore only a point was put in at that angle.
View 2 Replies
View Related
Aug 7, 2013
I want to use the custom unfolding rules using Bend Compensation with an angular reference to the bending angle.
I have an Excel sheet where I have determined the bend allowance, the set back and from that, the bend compensation. When I compare these values to the values I get when using a K-factor linear unfolding method in Inventor, I get almost exactly the same results.
Tells me the formulas are working. So I implement the formulas in the custom equations. Exactly the same as in the Excel sheet. 10 degrees angle, great results! Yeah! 45 degrees, great results! More yeah! 90 Degrees, still going strong, I think I might make it!
100 degrees.... Fail! Every time an angle goes over 90 degrees, the result is crap.
I have been struggling with this all day long!! So in the end I completely erased the equations from the Inventor custom equations.I just say: Compensation is 1 mm. For all angles. This should no room for interpretation.
Again I try. I have a sheet metal part with two legs. A 100mm leg and a 50mm leg. Flat pattern should always be 151mm. Period.
Again, under 90 degrees and on 90 degrees, I get nice flat patterns. Above 90 degrees, it fails again.
Am I completely overlooking something obvious?? Or is Inventor really bugging on this?
I am working on 2012 SP 2
View 9 Replies
View Related
Apr 5, 2013
I have very little knowledge in complex Autolist routines and routine to do the following:
I would like to be able to provide a Prefix and/or Suffix via dialog then pick any line of text or multiple lines of text and have it concentrate. For example: Prefix: First Floor Suffix: M100. I pick the room text on an arch floor plan "Mechanical room" and the second line "100" The result will be "First Floor Mechanical room 100 M100".
But lets take it a final step further; once condensed, I want it added to a perticular tag attribute in a block I inserted.
Example of how I would use it. I insert a symbol for an addressable smoke detector that has several tags; one of them being Location. I would use this routine to gather the information provided by the Arch floor plan and join it with the block attribute for exporting later for use in the Fire Alarm Panel Programming.
attached is a sample block with the attributes.
View 9 Replies
View Related
