AutoCAD Dynamic Blocks :: How To Make Angular Dimension Show Zero Degree
Sep 5, 2013
I have a block of a guide sign with directions and azimuth angles. I made arrows rotatable and angles were changing ok. But when I try to rotate an arrow into zero position, dimension shows 180. I need the dimension to show 0 degree. How can I do it?
And I can’t make angular dimension show degrees greater than 180 even if I specify vertex – after rotation angle shifts on the other side. I gave up and used back azimuth.
And I can't make an attachment: "The contents of the attachment doesn't match its file type"?
View 2 Replies
ADVERTISEMENT
Jan 17, 2013
How do i get the leading zero to show on an angular dimension for the seconds? as in: 108d 36' 03" ?
View 1 Replies
View Related
Sep 9, 2012
is there any way I can place dimension on drawing that would be in dual units (in decimal degrees and in deg min sec)?
I did not find this possible so far.
View 2 Replies
View Related
Jan 4, 2014
I have a drawing with dimensions. Now, I want create Dynamic Block Controlling Visibility with dimensions in drawing with name dimension.
LT-don-TD LT-Kdoc-TD LT-Kngang-TDLT-don-thay LT-Kdoc-thay LT-Kngang-thayLT-don-moi LT-Kdoc-moi LT-Kngang-moiH-don-TD H-Kdoc-TD H-Kngang-TDH-don-thay H-Kdoc-thay H-Kngang-thayH-don-moi H-Kdoc-moi H-Kngang-moi
Then, I use command DAL; I can select dimension want use.
View 8 Replies
View Related
Mar 26, 2012
I'm trying to make a dynamic block of a column radiator.
It should be very simple. It's a 46mm wide module that comes in a range of heights (300, 500, 600, & 750mm) and a range of assembly widths (9, 13, 18, 22 & 27 modules wide - more commonly given as mm widths of 414, 598, 828, 1012 & 1242 respectively).
My attempt at constructing it has gone quite well, but when 'stretching' the block a ghost of the core 414 (w) x 300 (h) unit remains. I attach the block to give you a better idea of what I mean.
View 4 Replies
View Related
Jul 20, 2011
Is it possible to constrain a dimension to an entity?
Outside the block editor you can display a constrained dimension with a dimension style but it doesn't appear as you can do the same inside blocks.
I want show the dimension of a line in a block that is constrained by a dimensional constraint but I can't figure out how to constrain the dimension extents to anything.
I could put in an attribute but it doesn't look like you can constrain attributes either. And then I would need to work out how to pass the value into it.
View 2 Replies
View Related
Jul 28, 2011
I try create simple block where I change dimensions of polylines. Everything work with stretch partameter until I try use search parameter for change dimension.
View 4 Replies
View Related
Dec 5, 2013
I have a line with shapes on each end like an aligned dimension. I want to have a grip on each end to let the user put the ends where they want.
I tried a polar stretch pair, with two rotation pairs, but am lost. The stretch is easy, but does not rotate the arrows to stay aligned to the line. I don't actually have arrows, but most know the behavior of aligned dimensions. I don't have extension lines though, like the dim would so ignore that part.
View 5 Replies
View Related
Oct 21, 2013
why after selecting Dimension, Angular, then selecting two lines, I do not get the angle between them? I am using v 2000 if it matters. I enclose a screen shot of the two lines I need the angle of.
View 9 Replies
View Related
Mar 21, 2013
Why does my angular dimension have a straight dimension line instead of curved?
View 4 Replies
View Related
Nov 4, 2009
I have attached my current block that I use for labeling my details on sheets. I'm trying to learn how to make dynamic blocks and I'm not having the best of luck just yet. What I'd like to be able to do is make this block dynamic and make it so that it has a list of scales that you can pick from. When you pick a scale (say 3/4"=1'-0") it will automatically fill out the "scale" attribute.
Another thing I'd like to do is instead of having to use %%U to underline the title, I'd like the little line attached to the circle (delete the underline and you'll see it) to stretch automatically with the length of the title text.
View 8 Replies
View Related
Oct 20, 2011
Is there any way possible to have an angular dimension to denote an angle of greater than 180 degrees?
View 4 Replies
View Related
Mar 26, 2012
I am trying to put an angular dimension from a hole to a slot positioned planes 90degrees to each other. How can I achieve this? Typically, it depends on how it is put into the ipt file but I didn't know how else to put the slot in therefore only a point was put in at that angle.
View 2 Replies
View Related
Jun 27, 2013
I produce windows and doors. and I reproduce the same drawing in the attachment a lot.
Is there a way to make it a dynamic block where I change the three dimensions in the drawing and the whole thing grows or shrinks symmetrically and proportionally?
View 9 Replies
View Related
Apr 10, 2012
The only formats I see for angular dimensions in the toolbox are degrees, °, radians, gradians. Is there any way set angular units be deg-min-sec (° ' ") format?
View 2 Replies
View Related
May 5, 2010
I've made annotative blocks and I've made dynamic blocks... My intent is to integrate both but I can't find a way to move dynamic block parameters separately at different annotative scales.
In other words, if I insert an annotative dimension and add multiple scales I can move the dimension grips independently at each scale. If I insert a dynamic block I want to be able to use the dynamic block's action "grips" to do the same. However, with a dynamic block, if I move a stretch action at one annotation scale it moves the action at all annotation scales.
The attached file shows a simple example.
View 2 Replies
View Related
Jun 25, 2013
Cannot find a way to set up angular dimensions to show that first zero if the minutes or seconds value is less than ten.
Desired: <degrees>08'05"
Stuck with: <degrees>8'5"
View 1 Replies
View Related
Mar 15, 2012
I have created a dynamic block with several visiblility states. The block works great for what I need it for. however, I am trying to add one more action to the block but am having issues.
This block is essentially a 24" retail cabinet with the visibility states showing the different drawer and shelf configurations. I want to be able to lengthen the cabinet in 24" increments and have the visibility show for each 24" section.....e.g. I want a 10' cabinet so I bring in the 24" starter block. Then stretch the cabinet to the 10' mark, then I can chose any drawer/shelve config for each 24" section (they are all different).
I can get the block to stretch in 24" sections....no problem.....i just want the visibility state to be duplicated as well for each section. Now as it stretches, there is only one Vis state and it only populates the first cabinet.
I could do this by copying the block over and over 5 times.....but I am hoping there is a way to make this dynamic.
View 7 Replies
View Related
Apr 23, 2013
I have a block I am making into a Dynamic Block. I will be adding in different visibility states. Depending on the visibility state the block would need to be inserted from a different point.
My question is, is it possible to add multiple insertion points to a dynamic block so depending on the visibility state it defaults to the correct insertion point?
View 2 Replies
View Related
Dec 13, 2012
All I want to do is rotate one dimension. I want to leave all the others alone.
When I am editing my drawing, I double click on the dimension and get the diag box and unfortunately the rotate dimension command along with the degree box is grayed out.
View 2 Replies
View Related
May 7, 2010
I'm trying to create a dynamic block for plywood. I have the stretch parameter working so that I can stretch the plywood to the needed length. I also have set a rotation parameter based on the various roof pitches that we use. The problem is I would like to be able to rotate the sheathing to a 45 degree angle and then stretch along the 45 degree angle. Once I rotate the sheathing the stretch does not follow the rotation angle. I have attached the file.
View 9 Replies
View Related
Sep 7, 2012
is there a way to make dynamic blocks stretchable similar to a mleader,
the blocks i create are only stretchable by grips, and not by crossing
(i am using linear or point parameter stretches)
View 2 Replies
View Related
Jun 1, 2006
Is there anyway to link standard AutoCAD Grips and there commands to Dynamic Block Actions? I want to stretch an arc by its midpoint grip. This accomplishes something that no other commands do.
View 4 Replies
View Related
Jun 5, 2012
I would like to make a 1" long, 1" diameter straight pipe as a block. I would like to insert that block into my drawing, say...on a 90 degree elbow. After inserting the straight stub, I would like to use a grip to "stretch" the pipe length to the next fitting. Ultimately, I would like to compile a parts list for my pipe drawing that will give me the straight pipe length. I've been doing some searching and 3d dynamic blocks seem to be impossible.
View 2 Replies
View Related
Mar 22, 2013
So I've done a reasonable amount of work with dynamic blocks. I have a block with a rotation action and grip to arbitrarily align it. However I realized when trying to combine it with an alignment grip (which actions on the basic or fundamental block rotation angle) that there didn't seem to be a way to some how link a dynamic block rotation action or one of the custom angle properties to a the fundamental block rotation angle. Thus there are two additive rotations at work; the dynamic block one with its grip and the fundamental rotation property.
This can cause some confusion when one person aligns with the grip and another via rotating the block's fundamental property and would also be problematic in the generalized sense if one was trying to select or programmatically read back the net angle alignment.
View 2 Replies
View Related
Jun 13, 2013
I have a dynamic block, that represents a stirrup.
I inserted in the block a Block Propreties Table, that have some preset dimensions for the stirrups. The grip of this table I decided to put in the top right corner.
The problem is that I can't make this grip moveable )
See the attachement with the block
View 1 Replies
View Related
Jul 25, 2012
new to dynamic blocks but looking to streamline my wiring diagrams here and have created a block that shows the typical wire styles we use in a simple easy way. I now want to add an overall flip to the entire block and have not been able to find set this. I would prefer to use the same label and go from there. I have included the block to show what I mean. It is only working on the single visible item at the one time. I know this has to be possible just let me know what I am doing wrong. I am running AutoCad LT 2013
View 3 Replies
View Related
Feb 28, 2012
I need to create a dynamic block for a "Glass Panel" in a balustrade. I need to be able to insert it, in one corner and stretch it in another corner, to suit the staircase angle.
I've created the block, but it isn't working correctly. I've attached a drawing, with the left hand drawing a sketch of how it needs to be. The right hand drawing is my dynamic block attempt. As can be seen, when the block is stretched between the 2 points, it doesn't follow the angle of the staircase correctly (Very slight run off)
View 9 Replies
View Related
Nov 21, 2011
I wish to create a dynamic block containing some attributes. These attributes are inside rectangles that can't be modified in length using linear parameters ; but the attribute has to be always in the middle of the rectangle. So, I draw a line inside the rectangle (in a hidden layer) and insert the attribute with center justification (not sure for the translation) that I place in the middle of this line ; then I put a coincidence constraint (not sure for the translation, but it's the first one) linking the middle of the line with the middle of the attribute.
But here's the problem : when stretching my rectangle, the insertion point of the attribute suddenly changes from "center" to "bottom left".
View 2 Replies
View Related
Dec 4, 2013
I am looking for a way to use the ATTIN/ATTOUT workflow to bring in data from an excel spreadsheet to drive the size of each of my block's instances. The block will be simple, a rectangle, with width and length parameters. For each entity in my excel/csv file these parameter values are spelled out. I know how to display these parameters in my attributes, but I don't know how, if I were to feed in these values, to drive the geometry. If there's a better way to take a list of width and length values to generate a series of blocks each with a rectangle containing its respective size.
View 1 Replies
View Related
Nov 7, 2011
I need to do some repetitive task on a lot of dynamic blocks, unfortunately, when I open each file, AutoCAD keeps asking if I want to open it with the block editor.
Is there a way to disable that dialog and open the files as normal dwgs?
A hint: BLOCKEDITLOCK doesn't make it, it shows another dialog...
View 4 Replies
View Related
