AutoCAD Dynamic Blocks :: Make 1" Long / 1" Diameter Straight Pipe As A Block
Jun 5, 2012
I would like to make a 1" long, 1" diameter straight pipe as a block. I would like to insert that block into my drawing, say...on a 90 degree elbow. After inserting the straight stub, I would like to use a grip to "stretch" the pipe length to the next fitting. Ultimately, I would like to compile a parts list for my pipe drawing that will give me the straight pipe length. I've been doing some searching and 3d dynamic blocks seem to be impossible.
I have created d/blocks for my different pipe sizes i.e one block with a dropdown to select the different sizes and have done the same for my flanges. now how do I link / insert the flange d/block to the piping block so that I can export the information into a material list later on.
I'm trying to make a dynamic block of a column radiator.
It should be very simple. It's a 46mm wide module that comes in a range of heights (300, 500, 600, & 750mm) and a range of assembly widths (9, 13, 18, 22 & 27 modules wide - more commonly given as mm widths of 414, 598, 828, 1012 & 1242 respectively).
My attempt at constructing it has gone quite well, but when 'stretching' the block a ghost of the core 414 (w) x 300 (h) unit remains. I attach the block to give you a better idea of what I mean.
The AttSync command does what it advertises fairly well. My problem is that I have thousands of small blocks in a single drawing. (My current drawing has 2100 block references with four attributes in each one.) I may change the attribute values in a few of them and need to re-sync the attribute locations. When I run AttSync it updates every single block insertion. One of two things are desired:
1)Flag each block insertion as having been sync'ed, reducing the number of objects requiring synchronization when AttSync is called again. Provide a way to force all to be sync'ed.
2)Allow a selection set in the AttSync command after selecting the block to sync.
Either or both of these would a great time-saver for those of us with large numbers of blocks with attributes.
I have been off playing in the Inventor world for awhile and now that I am back in the 2D world, I find my memory fails me. I am trying to create a dynamic block for terminal boxes. Some of these boxes are round so I need to control the diameter from the lookup table. Just how do I do that? Placing a diameter constraint parameter gets me the various diameters I need but I cannot get those into the lookup table.
I'm trying to create a dynamic block that uses a parameter and an attribute definition to determine the diameter of a circle in that block. I plan to export GIS points with diameter in the attribute table into a CAD file with the block definition. I'm having trouble figuring out how to set up the parameters to read to attribute definition and adjust the circle diameter. Using AutoCAD 2013
I am really struggling to get this dynamic block working - It's a plan view on the flight of steps and I would like to space the risers equally between the bottom and top nosing. I was trying to use array but the value (tread going) stays the same... So I need something thath would work just like divide command.
Eventually I need a block with different tread numbers which will be just a matter of creating a few visibility states
So I've done a reasonable amount of work with dynamic blocks. I have a block with a rotation action and grip to arbitrarily align it. However I realized when trying to combine it with an alignment grip (which actions on the basic or fundamental block rotation angle) that there didn't seem to be a way to some how link a dynamic block rotation action or one of the custom angle properties to a the fundamental block rotation angle. Thus there are two additive rotations at work; the dynamic block one with its grip and the fundamental rotation property.
This can cause some confusion when one person aligns with the grip and another via rotating the block's fundamental property and would also be problematic in the generalized sense if one was trying to select or programmatically read back the net angle alignment.
new to dynamic blocks but looking to streamline my wiring diagrams here and have created a block that shows the typical wire styles we use in a simple easy way. I now want to add an overall flip to the entire block and have not been able to find set this. I would prefer to use the same label and go from there. I have included the block to show what I mean. It is only working on the single visible item at the one time. I know this has to be possible just let me know what I am doing wrong. I am running AutoCad LT 2013
I need to create a dynamic block for a "Glass Panel" in a balustrade. I need to be able to insert it, in one corner and stretch it in another corner, to suit the staircase angle.
I've created the block, but it isn't working correctly. I've attached a drawing, with the left hand drawing a sketch of how it needs to be. The right hand drawing is my dynamic block attempt. As can be seen, when the block is stretched between the 2 points, it doesn't follow the angle of the staircase correctly (Very slight run off)
I wish to create a dynamic block containing some attributes. These attributes are inside rectangles that can't be modified in length using linear parameters ; but the attribute has to be always in the middle of the rectangle. So, I draw a line inside the rectangle (in a hidden layer) and insert the attribute with center justification (not sure for the translation) that I place in the middle of this line ; then I put a coincidence constraint (not sure for the translation, but it's the first one) linking the middle of the line with the middle of the attribute.
But here's the problem : when stretching my rectangle, the insertion point of the attribute suddenly changes from "center" to "bottom left".
I am looking for a way to use the ATTIN/ATTOUT workflow to bring in data from an excel spreadsheet to drive the size of each of my block's instances. The block will be simple, a rectangle, with width and length parameters. For each entity in my excel/csv file these parameter values are spelled out. I know how to display these parameters in my attributes, but I don't know how, if I were to feed in these values, to drive the geometry. If there's a better way to take a list of width and length values to generate a series of blocks each with a rectangle containing its respective size.
I have a drawing ("SURUBURI.dwg") with several dynamic blocks ("M12", "M16", "M18" ... an so on...). I want to insert in my current drawing, one of the blocks from SURUBURI.dwg, for instance the block named "M12".
For that i tried creating a new command "INSERT_M12" that has the following script :
I have successfully created a dynamic block. I can insert it into AutoCAD, and it behaves like I want, except for one thing.
I can select the block and change it by taking a grippoint and place it at another position. So my block is e.q. stretched, just like I wanted.
But then. When I want to use the ordinary STRETCH command of AutoCAD, I can only stretch the insertion point of the block, but not the grippoints. Is there a way to set a grippoint to be select edable by commands like STRETCH.
I am currently freelancing for my current boss and have a question regarding dynamic blocks. We deal in water and waste water drawings, so I deal with pipe fittings and such. Right now the other guy working with us (former coworker also) has blocks for each and every fitting.. So the block library is big..
I would like to reduce the size drastically and think dynamic blocks can work with that.
So basically, to start with, I attached a dwg of a 3" blank flange (which is the end of the pipe basically)..we have these blocks going all the way up to 24"..seeing how its just the size that changes, i would like to create a dynamic block that will do this for me by just selecting the size i need.
Problem: I forgot how to work with dynamic blocks!!
This is just a simple flange block that i want to start with, than once i get this down and learn about them i will update the rest (bends, reducers, tees, etc)
Also, I am using 2012 release..what release did dynamic blocks come out in?
I have a dynamic block with several actions and parameters. There are three grip points. Two are visible. One appears when you move one of the other grips. If i insert or paste this block near my template, the X/Y basepoint stays near the template when i drag the block on the template with one of the other two grips.. When i print the drawing the basepoint stays visible and the scale on my printed drawing is not correct (smaller).
I am creating a dynamic block of a conveyor belt it has a set number of widths and needs to be stretchable in length, which I have managed to do. The motor is placed half way down the length of the conveyor and needs to stay centered
I know I need to use the move command and put in a factor of 0.5 somewhere, but I can't remember how to do it.
Is it possible to mirror a rotation within a dynamic block?
See the attached drawing. I am trying to have two rotations within a dynamic block, but only one grip. When the grip is rotated one half of the block rotates while the other half rotates in reverse. The resulting action would be much like the wings of a butterfly.
I have tried many different combinations of parameters, actions and constraints with no luck. The block in the attached file was as close as I could get. Have I reached the end of what AutoCAD is capable of?
I have a block of a roof screen. What i want to do is to stretch it & have the slats on the front & also the supports on the rear array @ different intervals. The slats on the front would array every 6-1/2" (The slats are 5-1/2" wide with a 1" gap). The supports array every 4'-0". I have tried to do this multiple ways with mixed results. How to get my desired outcome. I am enclosing my block.
Last week I opened the drawing and added some visibilty states etc. to the block.
Now when I open the block or insert it into another drawing for whatever reason the cursor or crosshairs stop at the edge of the block. And if you move towards the middle of the block where there isn't any lines etc. the cursor will move to that point until you hit another line then it will stop moving again.
I've been reading some other posts for different dynamic block topics/issues and read that everyone has problems when you get to higher numbers of visibility states, but when I edited last week I only added 7 states. Is that enough to make this happen? It sounds like everyone else that is having problems has far fewer visibility states than on the attached drawing.
I am looking to create a dynamic block that changes in scale, ex. If I have two (2) viewports in paper space, one 1/4"=1'-0" the other 1/8"=1'-0" I want my blocks to appear to be the same size in paper space.
Also, I would like my blocks to change attributes/features ex. If I have a "light switch block" I would like to have the option of switching the block from a 3-way switch, 4-way switch etc.