AutoCAD Dynamic Blocks :: Stretch Dynamic Block Grip Points
Feb 4, 2011
I have successfully created a dynamic block. I can insert it into AutoCAD, and it behaves like I want, except for one thing.
I can select the block and change it by taking a grippoint and place it at another position. So my block is e.q. stretched, just like I wanted.
But then. When I want to use the ordinary STRETCH command of AutoCAD, I can only stretch the insertion point of the block, but not the grippoints. Is there a way to set a grippoint to be select edable by commands like STRETCH.
View 9 Replies
ADVERTISEMENT
Jan 24, 2013
I have created a dynamic block with stretch points. I used the tester in the block editor and all works fine, but when I insert the block into a drawing, the grips for the stretch action are in a completely different place...I don't mean a different place on the block, but a different place in the drawing...way out there. so if I go into the block editor for the block while I'm in the drawing...the parameters have now moved way out of the way also, in the block...but if I actually open up the block itself and then go into the block editor, all the parameters are where i placed them in the first place.
View 1 Replies
View Related
Apr 4, 2012
Is there a way to have the grip stay in the correct position when the distance multiplier is .5? It seems to "get ahead" of the original location.
In the attached block, when I stretch the block with the grip, the grip ends up off the end point. Both actions have a .5 multiplier, with the left side having a rotation of 180 - so both sides stretch equally in opposite directions.
Also, there are 3 views with parameters (width/depth). Is there a way to get the user to enter in the sizes without having to select the size on each view? Basically a table that has a 'user input' field so the size selected changes everything at one time.
View 7 Replies
View Related
Jun 13, 2013
I have a dynamic block, that represents a stirrup.
I inserted in the block a Block Propreties Table, that have some preset dimensions for the stirrups. The grip of this table I decided to put in the top right corner.
The problem is that I can't make this grip moveable )
See the attachement with the block
View 1 Replies
View Related
Nov 15, 2012
I have a dynamic block with several actions and parameters. There are three grip points. Two are visible. One appears when you move one of the other grips. If i insert or paste this block near my template, the X/Y basepoint stays near the template when i drag the block on the template with one of the other two grips.. When i print the drawing the basepoint stays visible and the scale on my printed drawing is not correct (smaller).
View 9 Replies
View Related
Jul 4, 2013
How do I stretch a hatch in dynamic block? It does not seem to work if I select the hatch along with other lines of a counter block.
View 2 Replies
View Related
Aug 7, 2011
I have this double click class. which works fine. In order to clear grips after user finishes with double clicking,I added two lines (which shown on code below). But having those two line make code faulty. When ?
if user select a dynamic block with stretch grip on it, then double click on stretch grip trianlge. code geneaarte fatal error. Funny thing is code doesn't catch. it. Is there any other way to clear grips after double click ?
Here is code:
Imports Autodesk.AutoCAD.RuntimeImports Autodesk.AutoCAD.ApplicationServicesImports Autodesk.AutoCAD.EditorInputImports Autodesk.AutoCAD.DatabaseServicesPublic Class Main_0_Class Implements IExtensionApplication Public Sub Initialize() Implements IExtensionApplication.Initialize dblClickEven_Class.Start() End Sub
[Code] .....
View 7 Replies
View Related
Nov 16, 2011
If you have a drawing open and the Tool Palette Architectural open click on the door. It has "tick marks" where you can stretch the doors opening to (24", 32"). I want to know how to add those "tick marks" to my blocks .
View 4 Replies
View Related
Jun 27, 2011
A simple dynamic block using a Block Properties Table to control the value of an attribute. The block also has flip & rotate actions, but I cannot get the Block Table grip to flip or rotate with the rest of the block even though it is part of both selection sets.
View 1 Replies
View Related
Oct 11, 2012
What is the variable to change the dynamic grip parameter size and color.
View 3 Replies
View Related
Mar 18, 2013
I am working on a dynamic block that I figured would be fairly simple. However, it is proving to be a huge annoyance. What I want for it to do is stretch the end of a polyline with a stretch action, while at the same time moving the grip of my block properties table. No matter what I do to it, the block properties grip won't move/stretch.
View 4 Replies
View Related
Dec 12, 2013
I have drawn a simple block that I want to stretch in two directions manually or from the properties palatte.
My block works fine once and then breaks down. Stretch the block in the 'Y' direction. Deselect the block. Stretch the block again and only the grip moves. Edit the block and close the block, the block resets.
View 6 Replies
View Related
Jul 31, 2012
I need this block to do the following:
1. Move the right piece so it ends at 3', 4', & 5'.
2. the move right hook and 'backing' to stretch/copy (or array) so it adds a hook to the right and fills in the backing.
so this means that a 3' gets 4 hooks, 4' gets 5 hooks and 5' gets 6 hooks.
3. the block as shown is the smallest configuration with 3 hooks.
I could just set up a visibility and draw each one at it's appropriate length but I'm trying to keep this simple block to a min size. If all else fails, that's the route I'll take.
I've tried a couple different configurations and I keep getting duplicates or the end piece doesn't move the correct distance.
View 3 Replies
View Related
Jul 13, 2013
I am trying to put a polar stretch on the block uploaded, but it doesn't seems to work (maybe because of my constraint? ). If something major is wrong with it, is there another way I can make the same drawing proportional when i rotate it and stretch it ? Also, after that I have to use it for vlisp.
View 5 Replies
View Related
Jun 27, 2013
I've got a rectangular block that I need to stretch by both ends at the same time, maintaining the center/insertion point as it grows. I have attached the block to show what I'm working with.
I thought Linear Stretch Pair was the answer but I can't make it work.
View 5 Replies
View Related
Jun 18, 2012
Is it possible to stretch block depending of the insertion point so that the bottom part is always on the same high.
See attached image.
View 8 Replies
View Related
Nov 30, 2010
I have a dynamic block that I would like to insert via a lisp routine. When the routine is run from my menu I would like to select two points on the drawing area. Then I would like my dynamic block to be inserted at one of the points I selected and then I would like a specific "point" of my block to be stretched to the other point that I selected. I was wondering if this is possible with LISP? I have my old LISP program I wrote that draws a leader and then inserts my block but that was before I started working with dynamic blocks.
Here is my current
(defun c:wldsym()
(setq osnapold (getvar "osmode"))
(setq orthold (getvar "orthomode"))
(setq dimsc (getvar "dimscale"))
[code]...........
wld1r.dwg is my current block. It has some dynamic properties already. But I'm trying to add new properties that can be seen in my working test drawing wld1r-new.dwg
When using my code with "wld1r.dwg" you can see how everything behaves right now. Then open "wld1r-new.dwg" and note that the insertion point and a stretch point my default are in the same spot. Work with the two stretch points and look at how the block reacts.
View 9 Replies
View Related
Mar 22, 2013
So I've done a reasonable amount of work with dynamic blocks. I have a block with a rotation action and grip to arbitrarily align it. However I realized when trying to combine it with an alignment grip (which actions on the basic or fundamental block rotation angle) that there didn't seem to be a way to some how link a dynamic block rotation action or one of the custom angle properties to a the fundamental block rotation angle. Thus there are two additive rotations at work; the dynamic block one with its grip and the fundamental rotation property.
This can cause some confusion when one person aligns with the grip and another via rotating the block's fundamental property and would also be problematic in the generalized sense if one was trying to select or programmatically read back the net angle alignment.
View 2 Replies
View Related
Jul 25, 2012
new to dynamic blocks but looking to streamline my wiring diagrams here and have created a block that shows the typical wire styles we use in a simple easy way. I now want to add an overall flip to the entire block and have not been able to find set this. I would prefer to use the same label and go from there. I have included the block to show what I mean. It is only working on the single visible item at the one time. I know this has to be possible just let me know what I am doing wrong. I am running AutoCad LT 2013
View 3 Replies
View Related
Feb 28, 2012
I need to create a dynamic block for a "Glass Panel" in a balustrade. I need to be able to insert it, in one corner and stretch it in another corner, to suit the staircase angle.
I've created the block, but it isn't working correctly. I've attached a drawing, with the left hand drawing a sketch of how it needs to be. The right hand drawing is my dynamic block attempt. As can be seen, when the block is stretched between the 2 points, it doesn't follow the angle of the staircase correctly (Very slight run off)
View 9 Replies
View Related
Nov 21, 2011
I wish to create a dynamic block containing some attributes. These attributes are inside rectangles that can't be modified in length using linear parameters ; but the attribute has to be always in the middle of the rectangle. So, I draw a line inside the rectangle (in a hidden layer) and insert the attribute with center justification (not sure for the translation) that I place in the middle of this line ; then I put a coincidence constraint (not sure for the translation, but it's the first one) linking the middle of the line with the middle of the attribute.
But here's the problem : when stretching my rectangle, the insertion point of the attribute suddenly changes from "center" to "bottom left".
View 2 Replies
View Related
Dec 4, 2013
I am looking for a way to use the ATTIN/ATTOUT workflow to bring in data from an excel spreadsheet to drive the size of each of my block's instances. The block will be simple, a rectangle, with width and length parameters. For each entity in my excel/csv file these parameter values are spelled out. I know how to display these parameters in my attributes, but I don't know how, if I were to feed in these values, to drive the geometry. If there's a better way to take a list of width and length values to generate a series of blocks each with a rectangle containing its respective size.
View 1 Replies
View Related
Nov 7, 2011
I need to do some repetitive task on a lot of dynamic blocks, unfortunately, when I open each file, AutoCAD keeps asking if I want to open it with the block editor.
Is there a way to disable that dialog and open the files as normal dwgs?
A hint: BLOCKEDITLOCK doesn't make it, it shows another dialog...
View 4 Replies
View Related
Mar 26, 2012
I'm trying to make a dynamic block of a column radiator.
It should be very simple. It's a 46mm wide module that comes in a range of heights (300, 500, 600, & 750mm) and a range of assembly widths (9, 13, 18, 22 & 27 modules wide - more commonly given as mm widths of 414, 598, 828, 1012 & 1242 respectively).
My attempt at constructing it has gone quite well, but when 'stretching' the block a ghost of the core 414 (w) x 300 (h) unit remains. I attach the block to give you a better idea of what I mean.
View 4 Replies
View Related
Jul 16, 2010
I have a drawing ("SURUBURI.dwg") with several dynamic blocks ("M12", "M16", "M18" ... an so on...). I want to insert in my current drawing, one of the blocks from SURUBURI.dwg, for instance the block named "M12".
For that i tried creating a new command "INSERT_M12" that has the following script :
^C^C-INSERT; "I:/Ionut Mihaila/Goodies/SURUBURI.dwg/M12"
Now obvious that doesn't work, but i think it shows clearly what i want to accomplish. So is there an other way to do this?
View 9 Replies
View Related
Sep 18, 2013
I'm working on a drawing and I want an action to work on two diffrent dynamic blocks.
In my case, I wish to have two blocks that I can rotate by one rotation grip.
How do I manage to work this out?
View 1 Replies
View Related
Mar 1, 2013
I would like to create a "wave" dynamic block, see below...
It is made from wipeout.
Is it chance to make a similar?
If I make a list for the length (from 125 to 350), after can I make a table /list /summary where these size are shown?
View 9 Replies
View Related
Jun 27, 2013
Why the drawing title in my dynamic block will not scale up or down. The rest of the objects scale properly but just this the drawing title text attribute will not follow suit.
I tried adding position point and link, etc....I run out options and don't know how to fix this.
LT 2012 user
AutoCAD LT 2012
Windows 7 - 64 bit
View 3 Replies
View Related
May 29, 2013
I am creating a dynamic block of a conveyor belt it has a set number of widths and needs to be stretchable in length, which I have managed to do. The motor is placed half way down the length of the conveyor and needs to stay centered
I know I need to use the move command and put in a factor of 0.5 somewhere, but I can't remember how to do it.
View 6 Replies
View Related
Jan 4, 2014
I have a drawing with dimensions. Now, I want create Dynamic Block Controlling Visibility with dimensions in drawing with name dimension.
LT-don-TD LT-Kdoc-TD LT-Kngang-TDLT-don-thay LT-Kdoc-thay LT-Kngang-thayLT-don-moi LT-Kdoc-moi LT-Kngang-moiH-don-TD H-Kdoc-TD H-Kngang-TDH-don-thay H-Kdoc-thay H-Kngang-thayH-don-moi H-Kdoc-moi H-Kngang-moi
Then, I use command DAL; I can select dimension want use.
View 8 Replies
View Related
Mar 5, 2012
I have an X centered as my insertion point.
When I stretch the dynamic block for a larger area the X stretches but into the next single box but not centered within the double space.
how to get the X to be centered in the box when it is enlarged to a double or triple size?
View 3 Replies
View Related
