I'm working on a drawing and I want an action to work on two diffrent dynamic blocks.
In my case, I wish to have two blocks that I can rotate by one rotation grip.
How do I manage to work this out?
So I've done a reasonable amount of work with dynamic blocks. I have a block with a rotation action and grip to arbitrarily align it. However I realized when trying to combine it with an alignment grip (which actions on the basic or fundamental block rotation angle) that there didn't seem to be a way to some how link a dynamic block rotation action or one of the custom angle properties to a the fundamental block rotation angle. Thus there are two additive rotations at work; the dynamic block one with its grip and the fundamental rotation property.
This can cause some confusion when one person aligns with the grip and another via rotating the block's fundamental property and would also be problematic in the generalized sense if one was trying to select or programmatically read back the net angle alignment.
I have created a dynamic block with several visiblility states. The block works great for what I need it for. however, I am trying to add one more action to the block but am having issues.
This block is essentially a 24" retail cabinet with the visibility states showing the different drawer and shelf configurations. I want to be able to lengthen the cabinet in 24" increments and have the visibility show for each 24" section.....e.g. I want a 10' cabinet so I bring in the 24" starter block. Then stretch the cabinet to the 10' mark, then I can chose any drawer/shelve config for each 24" section (they are all different).
I can get the block to stretch in 24" sections....no problem.....i just want the visibility state to be duplicated as well for each section. Now as it stretches, there is only one Vis state and it only populates the first cabinet.
I could do this by copying the block over and over 5 times.....but I am hoping there is a way to make this dynamic.
I have a dynamic block, that represents a stirrup.
I inserted in the block a Block Propreties Table, that have some preset dimensions for the stirrups. The grip of this table I decided to put in the top right corner.
The problem is that I can't make this grip moveable )
See the attachement with the block
new to dynamic blocks but looking to streamline my wiring diagrams here and have created a block that shows the typical wire styles we use in a simple easy way. I now want to add an overall flip to the entire block and have not been able to find set this. I would prefer to use the same label and go from there. I have included the block to show what I mean. It is only working on the single visible item at the one time. I know this has to be possible just let me know what I am doing wrong. I am running AutoCad LT 2013
View 3 Replies View RelatedI need to create a dynamic block for a "Glass Panel" in a balustrade. I need to be able to insert it, in one corner and stretch it in another corner, to suit the staircase angle.
I've created the block, but it isn't working correctly. I've attached a drawing, with the left hand drawing a sketch of how it needs to be. The right hand drawing is my dynamic block attempt. As can be seen, when the block is stretched between the 2 points, it doesn't follow the angle of the staircase correctly (Very slight run off)
I wish to create a dynamic block containing some attributes. These attributes are inside rectangles that can't be modified in length using linear parameters ; but the attribute has to be always in the middle of the rectangle. So, I draw a line inside the rectangle (in a hidden layer) and insert the attribute with center justification (not sure for the translation) that I place in the middle of this line ; then I put a coincidence constraint (not sure for the translation, but it's the first one) linking the middle of the line with the middle of the attribute.
But here's the problem : when stretching my rectangle, the insertion point of the attribute suddenly changes from "center" to "bottom left".
I am looking for a way to use the ATTIN/ATTOUT workflow to bring in data from an excel spreadsheet to drive the size of each of my block's instances. The block will be simple, a rectangle, with width and length parameters. For each entity in my excel/csv file these parameter values are spelled out. I know how to display these parameters in my attributes, but I don't know how, if I were to feed in these values, to drive the geometry. If there's a better way to take a list of width and length values to generate a series of blocks each with a rectangle containing its respective size.
View 1 Replies View RelatedI need to do some repetitive task on a lot of dynamic blocks, unfortunately, when I open each file, AutoCAD keeps asking if I want to open it with the block editor.
Is there a way to disable that dialog and open the files as normal dwgs?
A hint: BLOCKEDITLOCK doesn't make it, it shows another dialog...
I'm trying to make a dynamic block of a column radiator.
It should be very simple. It's a 46mm wide module that comes in a range of heights (300, 500, 600, & 750mm) and a range of assembly widths (9, 13, 18, 22 & 27 modules wide - more commonly given as mm widths of 414, 598, 828, 1012 & 1242 respectively).
My attempt at constructing it has gone quite well, but when 'stretching' the block a ghost of the core 414 (w) x 300 (h) unit remains. I attach the block to give you a better idea of what I mean.
I have a drawing ("SURUBURI.dwg") with several dynamic blocks ("M12", "M16", "M18" ... an so on...). I want to insert in my current drawing, one of the blocks from SURUBURI.dwg, for instance the block named "M12".
For that i tried creating a new command "INSERT_M12" that has the following script :
^C^C-INSERT; "I:/Ionut Mihaila/Goodies/SURUBURI.dwg/M12"
Now obvious that doesn't work, but i think it shows clearly what i want to accomplish. So is there an other way to do this?
I have successfully created a dynamic block. I can insert it into AutoCAD, and it behaves like I want, except for one thing.
I can select the block and change it by taking a grippoint and place it at another position. So my block is e.q. stretched, just like I wanted.
But then. When I want to use the ordinary STRETCH command of AutoCAD, I can only stretch the insertion point of the block, but not the grippoints. Is there a way to set a grippoint to be select edable by commands like STRETCH.
I would like to create a "wave" dynamic block, see below...
It is made from wipeout.
Is it chance to make a similar?
If I make a list for the length (from 125 to 350), after can I make a table /list /summary where these size are shown?
Why the drawing title in my dynamic block will not scale up or down. The rest of the objects scale properly but just this the drawing title text attribute will not follow suit.
I tried adding position point and link, etc....I run out options and don't know how to fix this.
LT 2012 user
AutoCAD LT 2012
Windows 7 - 64 bit
I have a dynamic block with several actions and parameters. There are three grip points. Two are visible. One appears when you move one of the other grips. If i insert or paste this block near my template, the X/Y basepoint stays near the template when i drag the block on the template with one of the other two grips.. When i print the drawing the basepoint stays visible and the scale on my printed drawing is not correct (smaller).
View 9 Replies View RelatedI am creating a dynamic block of a conveyor belt it has a set number of widths and needs to be stretchable in length, which I have managed to do. The motor is placed half way down the length of the conveyor and needs to stay centered
I know I need to use the move command and put in a factor of 0.5 somewhere, but I can't remember how to do it.
I have a drawing with dimensions. Now, I want create Dynamic Block Controlling Visibility with dimensions in drawing with name dimension.
LT-don-TD LT-Kdoc-TD LT-Kngang-TDLT-don-thay LT-Kdoc-thay LT-Kngang-thayLT-don-moi LT-Kdoc-moi LT-Kngang-moiH-don-TD H-Kdoc-TD H-Kngang-TDH-don-thay H-Kdoc-thay H-Kngang-thayH-don-moi H-Kdoc-moi H-Kngang-moi
Then, I use command DAL; I can select dimension want use.
How do I stretch a hatch in dynamic block? It does not seem to work if I select the hatch along with other lines of a counter block.
View 2 Replies View RelatedI have an X centered as my insertion point.
When I stretch the dynamic block for a larger area the X stretches but into the next single box but not centered within the double space.
how to get the X to be centered in the box when it is enlarged to a double or triple size?
Is it possible to mirror a rotation within a dynamic block?
See the attached drawing. I am trying to have two rotations within a dynamic block, but only one grip. When the grip is rotated one half of the block rotates while the other half rotates in reverse. The resulting action would be much like the wings of a butterfly.
I have tried many different combinations of parameters, actions and constraints with no luck. The block in the attached file was as close as I could get. Have I reached the end of what AutoCAD is capable of?
I have a block of a roof screen. What i want to do is to stretch it & have the slats on the front & also the supports on the rear array @ different intervals. The slats on the front would array every 6-1/2" (The slats are 5-1/2" wide with a 1" gap). The supports array every 4'-0". I have tried to do this multiple ways with mixed results. How to get my desired outcome. I am enclosing my block.
View 5 Replies View RelatedI have the attached file as a dynamic block.
Last week I opened the drawing and added some visibilty states etc. to the block.
Now when I open the block or insert it into another drawing for whatever reason the cursor or crosshairs stop at the edge of the block. And if you move towards the middle of the block where there isn't any lines etc. the cursor will move to that point until you hit another line then it will stop moving again.
I've been reading some other posts for different dynamic block topics/issues and read that everyone has problems when you get to higher numbers of visibility states, but when I edited last week I only added 7 states. Is that enough to make this happen? It sounds like everyone else that is having problems has far fewer visibility states than on the attached drawing.
I made a dynamic block with attributes. The block was to be moved using Linear parameter + move action, and then a lookup parameter and action.
The block moves as it is suppose to but the attributes are left behind. How can I get the attributes to move with the dynamic block?
The attribute properties are:
Verify = Yes.
Lock position: Yes or No don't seem to make a difference.
Is this a bug in AutoCAD or is there a solution to this?
I am looking to create a dynamic block that changes in scale, ex. If I have two (2) viewports in paper space, one 1/4"=1'-0" the other 1/8"=1'-0" I want my blocks to appear to be the same size in paper space.
Also, I would like my blocks to change attributes/features ex. If I have a "light switch block" I would like to have the option of switching the block from a 3-way switch, 4-way switch etc.
The block is a piping with various links that back together and they should stay behind each other, they are not go over each other otherwise the spacing is not good after data extraction.
The distance between not less than 100 mm and the total length should not exceed 5000mm are. Furthermore, they are relatively movable from each other.
I've been working with linear parameters and constraints, but that's not good as far as I know I can not apply visibility later with links that point to the other side.
I would like to create an "Y" dynamic block, see bellow.
The hole length and the "cross" point will be variable, between the two sticks will be 90 deg, and it will be FIX.
I would like if I change the "variable 2" distance the two sticks follow the cross point, and the top of the sticks stay in the same level, but between the sticks the 90 deg stay!
Sure wish you could manipulate the Column Offset of an Array Action with a Stretch Action.
CSHADEDESIGN|AUTOCAD LT|LT-KB|DYNAMIC BLOCKS
1. What is the easiest way to find points that are not constrained? I get a notice that the block is not fully constrained and its a nightmare going through all the lines trying to find where I need to apply a constarinet.( I can't wait to get off ACAD and back to Inventor.)
2. When I try to save a dynamic block using the Save Block icon under Open/Save, if the dynamic block is not fully constrained, and I click save, when I reopen the block to edit all of my constraints are gone, this has happened twice. Now I just exit by Xing out and saving changes.
Do you need to use the join command on an object before making it into a dynamic block? I have these stairs I need to scale down to fit my floorplan, but when I place grips on it in order to scale them down, I can only scale of the block while the rest becomes totally distorted.
View 3 Replies View RelatedI have a rather unusual problem. I'm using AutoCADLT2013. I have a dynamic block, with chained parameters. The block works perfectly, however, I'm expanding the contents, and trying to add more polylines to existing actions.
I have the following Actions showing: Stretch, Lookup, and Visibility. All of these actions are on unchained Parameters. The 2 Actions I'm missing are Arrays, both on chained Parameters with no Grips.
I've used ACTIONBAR on both Parameters (Show, then Hide, then Show again, I don't want to use Reset!), yet the Action Bars still won't show!
I've been messing for nigh on 2 hours and I can't figure it out. To make things worse, I can't use the Parameter Manager, due to it disappearing when in Block Editor.
I really don't want to have to start again, as it was a right pain in the rectum to get to work right.
I am in the process of fixing one of our dynamic blocks. It's a fairly simple fix where there was a typo in one of the names of our items in the lookup that needed to be fixed.
I changed the name of the item in the lookup table. I went and did the test block and it seemed to work fine, but when I bring the block into a drawing, it reverts back to the old lookup as if I did nothing at all.
I made sure that the path was correct and I even just dragged and dropped straight from Windows Explorer to no avail.Does AutoCAD keep referring to the old block? Did I forget to change something else?
