why my dimstyle appears different when I use different versions of AutoCAD.
In LT it is correct (left hand image), both styles are STANDARD font but in the full version (right hand image) the suffix text style is ROMANS.
In the dimension styles we have linear suffix and angular suffix. For angular dimensions we just want the degree symbol and for the Linear suffix we want the foot symbol. But when we dimension an angle we get both degree and a foot symbol, and we just want the degree symbol. We put the foot symbol on the linear units only yet it shows up on the angular dimensions.
View 5 Replies View RelatedI am using a dimension style that annoyingly adds the number "1/8" at the end of every angular dimension. Linear dimensions are fine.
I already checked and there is no suffix specified in the style. I also tried the dim/up feature, but the "1/8" still appears.
Degrees in "Units" are set to decimal. They are also set in decimal within the dimstyle.
Just to clarify, the number "1/8" is added after the actual dimension. I drew a 90 deg rectangle and the dim shows 90 1/8.
I could certainly try to create a new dimstyle from scrap, but perhaps any better tip.
I was wondering is there a way to export text, dimension, leaders and table styles? I have been trying for a while but can figure it out not even sure that you can.
View 5 Replies View Related(Again) The “leader” of the “dimension text” disappears when the text is moved! Why?
I’m wondering why the “leader” of the “dimension text” disappears when the text is moved.
How can I control this setting?
I need to show this “leader” all the time. Is that possible?
Please, have a look on the screenshots below (the file is attached).
We have many text entities in our drawing quoting a number "S3". We need to suffix that number with the text "PT" Most, if not all, of the "S3"'s are MText.
However, the "PT" text needs to be at about 70% of the size of the "S3" and be positioned almost like a superscript. It also needs to be a different colour for pen table reasons.
S3 = Colour 2, 0.35 text
PT = Colour 1, 0.25 text
My some autocad files were slowed down. For example i wait about 10 seconds when i edit a text.
Afterwards i see too many text styles in format/text styles command. i want to delete text styles but i can't.
it says "style in use, can't be deleted". I dont know where these text styles come from. Other files when they are infected with the virus, such as. Also have $ signs in text style names.
if i have a size indicated in my text style and i change the size from the style controls, updating the style, should all the instances not change to comply? This is how styles work in other software and how I intuit controlling this parameter.
View 1 Replies View RelatedWe have a problem in our office. In some of our drawings we keep getting a lot of unwanted linetypes and text styles. Nobody is sure where they originated.
We have tried this method in getting rid of them but it doesnt work. [URL]
See attached file.
Same applies with the text styles.
When I purge a drawing, the text styles are not a selectable option (as if there are no purgeable text styles). if i use (-purge), it will purge the unused text styles. I can also go into the Styles dialog box and delete the styles. It happens in all drawings and nobody else in the dept has the problem. I can't find any settings that would exclude any items from the purge dialog box as well. Autocad 2012? windows 7 64 bit.
View 1 Replies View RelatedAll of a sudden this morning when I dimension something, my dimension text is upside down. It is only on one drawing and only on new dimensions. why nad how to correct?
View 3 Replies View RelatedIs there a way to move the horizontal text of a vertical dimension that's outside of the extension lines to the right or left?
This was possible years ago with a simple stretch or moving of the text grip. Now, if the dimension is above the extension lines, the text is to the right. If it is below the extension lines, the text is to the left.
How do I edit a dimension text to add a second line (so dimension on top of the line and text on the second line)?
View 3 Replies View RelatedSame drawing (attached) with identical settings printed on one PC using DWG to PDF - creates this:
on another PC this:
So, some angle and aligned length dimensions are mirrored.
PDF previewed with Adobe Reader and Foxit PDF reader.
File is created and printed in 2010 LT, hence no UCS rotation, text style and print settings unaltered.
I have a problem to edit the dimension with autocad 2012. When i try to double click on the dimension text, i have a error message. This command doesn't exit.
View 3 Replies View RelatedI lost my dimension text on all my drawings when I converted with Windows 7. I did reload the 2010 software from scratch. I am thinking it is some type of .dll file issue or font issue.
View 9 Replies View RelatedHow to draw this object?
I want to draw an object similar to the dimension that contains two arrowheads with TWO “text dimension” to indicate the range each “steel bar” covers. This is important to indicate the range the two bars cover with the same dimension object.
Have a look on the screenshot below . The file is attached.
know if there a way to use fields in a table to pull the measurements out of dimensions snapped in a drawing (or layout) and place them in that table.
I create framing drawings and am looking for a quick way to put together a cut list without having to manually type dimensions into a table.
I have a rather weird problem. I am using .dxf files as digital overlays on a new optical comparator we recently purchased. The problem is, the cad files we used to create our old mylar overlays is both 3d and comprised of text/curves/dimensions. I figured out the flattening and turning the text into lines and curves, but I cannot find a method to change the dimension graphics (profile boxes, length dimensions, and angle dimensions) into lines and curves.
When I import them into the comparator program only the lines and curves can be displayed on the comparator. Is there any way to flatten and make all of the dimension graphics lines and curves?
If I place a dimension and have text above and below the dimension line (using X), and then grip edit the dimension text to move it for space/clarity on plans, the text above and below the line will mysteriously move closer to the line. If I have backgrounds applied to the text, which I normally do, the backgrounds will cover the line. Even without the background, it looks odd next to other dimensions that were not grip edited.
Civil 3D 2011
Windows 7 x64
I have very little knowledge in complex Autolist routines and routine to do the following:
I would like to be able to provide a Prefix and/or Suffix via dialog then pick any line of text or multiple lines of text and have it concentrate. For example: Prefix: First Floor Suffix: M100. I pick the room text on an arch floor plan "Mechanical room" and the second line "100" The result will be "First Floor Mechanical room 100 M100".
But lets take it a final step further; once condensed, I want it added to a perticular tag attribute in a block I inserted.
Example of how I would use it. I insert a symbol for an addressable smoke detector that has several tags; one of them being Location. I would use this routine to gather the information provided by the Arch floor plan and join it with the block attribute for exporting later for use in the Fire Alarm Panel Programming.
attached is a sample block with the attributes.
I created special dimension styles in Inventor 2013 in a drawing and trying to get them into another Inventor drawing. Can this be done like in Autocad by coping to the clip board and pasting into the new drawing?
View 2 Replies View RelatedI'm not able to create a
"DIMSTYLE" with Dimblk1 different Dimblk2
public static ObjectId CreateDimstyle(DimStyleTableRecord dim, string name, string seta1, string seta2) { Document acDoc = Application.DocumentManager.MdiActiveDocument; Database acCurDb = acDoc.Database; using (Transaction acTrans = acCurDb.TransactionManager.StartTransaction()) { DimStyleTable dimStyleTable = (DimStyleTable)acTrans.GetObject(acCurDb.DimStyleTableId, OpenMode.ForWrite); DimStyleTableRecord di
[code]....
I want to have two dimension styles in one dimension line. The first style would be a point to point dimension with the text centered and above the dimension line. The second style would be a running dimension to each point with the text over the second extension line and above the dimension line. Right now I am using two seperate dimension lines, one on top of the other. I'm trying to find a way to combine them into one dimension line so that I won't have to dimension the same thing twice.
At first I thought that using alternate units would work, however I was not able to find a way to seperate the two dimensions. Also, I didn't see how to make the alternate units a running dimension.
Is there a way to assign different dimension styles to different sheets in an idw. I have idw drawings with several sheets and use a couple of different dimension styles depending on what is on each sheet. I've created the dimension styles I want to use but I don't know how to assign a dimension style to a specific sheet. For now what I am doing is dimensioning, then as needed for the dimensions that need a different style, right click on the dimension and select new dimension style to changes its dimension style. I would like to assign dimension styles to specific sheets, is there a way to do this? Even though borders, title blocks, etc. are the same throughout the sheets, do I need to create different sheet formats to do this?
View 6 Replies View RelatedInside of the Style& Standard Editor (Manage-> Style editor) we use ANSI and a Company standard created off of ANSI.
But when I choose the filter to ALL STYLES, I can see JIS, DIN, All other unwanted styles. How can I get rid of them?
Do you all have them too? How do you get rid of them if you dint use them?
C1
Inventor Professional 2013
Vault Collaboration 2013
I always put the dimensions and text leaders in model space, is it true if I plan to have 3 different viewport scales, I would have to create 3 different dimension styles for each VP scale, it’s quite hard to predict in advance which VP scale that I am going to use, Let say I am going to use 1/8”=1’ what is the simple math formula to use?
View 3 Replies View RelatedWhen i match dimension styles from one viewport in layouts to another, all scaled to the same scale, the dimensions match nicely.
However if i move the second dimension, the one matched to the first, the dimension changes to another scale.
I received a file (exported from datacad) with apx. ~1000 dimension styles. I selected all dimensions and changed their style to a new style. Now I want to delete the old styles, but Autocad says they are used. I tried purging, but it doesn't work.
View 8 Replies View RelatedI would liketho know how it is done / is there a command for that, lisp.
View 1 Replies View RelatedHow do you make custom dimension styles global? How do you apply them to existing drawings with recreating each time.
Autocad Lt 2012
