As a hvac calculation engineer i often need to measure quickly pipes length and ventilation ducts area.
Measuring pipes lenght is quite easy with qselect + tlen.lsp, but, so far, how to measure ducts area quickly.
I'd like to add that ducts surface seen in 2D would satisfy me and i only talk about 2D drawings.
How to do this measure? Maybe there are lisp routines that could work?
We are able to measure distance in meters between 2 points using COGO tools. Though, when meassuring areas (command area) even setting units to meters it shows: "Area = 0.00000073, Perimeter = 0.00343123" which is not expressed in meters. The area in meters is around 8900m2. We are using latitude, longitude LL84 (WGS84). Is there a way to easily measure area over the map using this coordinate system?
View 1 Replies View RelatedFound that in certain drawings, the measure area tool will just suddenly stop working? It's very odd. It let's me pick points, but won't let me press enter to see the total.
Closing and reopening AutoCAD doesn't work. It seems to be a permanent thing to the affected drawing.
It's happened to me in a few drawings, but only in those specific ones. Other drawings are fine. I'm guessing it's a setting I've changed somehow?
I've been getting round it by creating shapes using the polyline, and then looking at the area in the properties window. It's an ok solution, but not ideal.
Is there an 'easy' way to see a cross sectional area and measure it? I have tried getting a cross-sectional area by off-setting a work plane into the model, sketching on that plane, and pressing F7.
This shows the cross-sectional area, but when I click the inspect>area I can not select the cross-section. Any thoughts besides creating a sketch on that surface and extruding it to remove; taking the area measurement, and then undoing the extrusion?
I’d like to ask how I can measure the area of a region, defined on a TIN surface. ( i.e. the area of the bounded topographic terrain )
View 8 Replies View RelatedI've figured some things out, but am struggling with what appears to be a very valuable tool... the area tool.
I found many references to the boundary tool, but that looks more complicated.
I have figured out how to mark the corner and press enter, but the output is for example 1.7 sq ft vs. what should be approx 35K sq ft.
I tried to change the units, but that didn't seem to make a difference.
I'm wondering if there is a lisp possible to measure area's by pick point (as in bpoly). This little feature exists in Microstation so i was looking for something similar.
Is it also possible if this lisp can measure areas from an external reference (dwg, dxf, dgn, shp etc..)? I'm kind of new to AutoCAD in that sence.
How to create a revolve surface in an assembly for the purpose of measuring a flow area through a specific area? See the attached JPG, I basically have a conical internal diameter with a pin protruding into it..... I need to measure the flow area as shown in the sketch attached here. the way I have this shown in the attached JPG is the way that we had previously performed this in Pro-e.
View 9 Replies View RelatedHow can i select areas of an image and find their size in pixels?
using the measure tool or image size only works for square (straight sided images).
I have cs3 extended. Is there a tool ( i can't find one) that will allow you to make a selection and then calculate the pixel area of the selection? For measuring areas in a scientific application.
View 8 Replies View RelatedWith Illustrator CS6, is there a way to measure/calculate the enclosed area of a given vector shape?
View 11 Replies View RelatedI need to be able to measure the square inches of a printed area in which hew will be using specialty inks. We want to get a descent cost estimate, how to measure the square inches of a specific element of a design, in Photoshop or any of the other adobe programs?
View 1 Replies View Relatedhow can I measure selected area of pixels using photoshop elements 12?
View 2 Replies View RelatedI've recently migrated from AutoCAD 2008 (non-industry specific) to AutoCAD 2010 so I don't know if this was an issue in 2009.
Back in 2008, when I choose the 'window' option when specifying a plot area, AutoCAD would show the workspace so that I could manually select a windowed plot area, and at the same time the whole workspace would be greyed out except the previously active window area.
This was handy, because we can have as many two dozen title-blocks (and therefore separate viewports) in paperspace, and knowing what plot area I last plotted or added as a saved page setup.
In 2010, it no longer does that. I now have to rely on the dashed border to know where the active plot area is/was (checked 'display printable area' in options>display tab) which I personally don't really like using.
How to changes the settings for the "Square Area" in mapcheck's closure summary. When I right-click the dwg name in the Settings tab of Toolspace and choose Edit Drawing Settings, then Ambient Settings, I see the Area settings, but in the closure summary, there is also "Square Area". Why are these both there? It WOULD be nice to show sq. ft. as well as acres, but I can't find anywhere to edit it.
Civil 3D 2012
Windows 7 Enterprise SP1
Dell Precision T3400
(Q9550 @ 2.83 GHz)
8GB RAM
Nvidia Quadro GTX 650 Ti BOOST
I want to know if there is an easier ACAD solution for drawing. In the given triangle of ABC (sides and angels are known) I want to draw line CM so that the area of BCM becomes 2000 cm (are of ABC is 5311.7 cm3).
Is there an easy ACAD way for drawing this line without using trigonometry for calculation?
I need to determine whether an area intersects with another area.The left case can be easily determined by Polyline.IntersectWith(Polyline...).But in the right case, the two polygons intersect/overlap each other while polylines do not intersect.
What would be the efficient way to determine the right case polygons are intersecting polygons?
Photo editing. How do I select an area within a .jpeg image so I can blur that selected area?
View 2 Replies View RelatedSee attached file.
How can you do the area takeoff of only the selected faces (red area)?
Right now I have to use the 3rd party software to do something like this. I'm curious if there's a way to do inside Revit?
After selecting the area type tool, I try to click and drag but I get an error message: You must click on a non-compound, non-masking path to create text inside a path. This worked before but I must have screwed something up.
View 3 Replies View Relatedis there any simple way to measure wireframes full lenght in inventor?
View 1 Replies View RelatedHow to measure the indicated angle? I’m wondering why the AutoCAD can’t measure the angles indicated (magenta) in the screenshot below! The dwg file is attached
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
I am doing takeoffs from a CAD drawing. Without getting too deep into it, I have one origin point, and then I have 200 or so points around the origin. I'm trying to find the fastest way to get the X offset, and the Y offset between each point and the origin.
Right now I'm drawing two lines to connect each point to the origin, then using PROPERTIES on the lines where they meet to get each length - I need to be able to see the numbers on the screen for a second while I copy them into a database. But I'm wondering if it would be easier to write a script, or if there happens to be a tool that could do this with fewer clicks.
Several people recommended DIMANGULAR. I have some concerns using this method because it is dependent on the precision of angular units in the drawings DIMSTYLE settings. For example, if a drawing file's DIMSTYLE has a precision set to the nearest whole decimal degree or only shows degrees and minutes but not seconds then the angle may appear at a certain angle, let's say perpendicular at 90 degrees. But in reality the angle might be slightly less than 90 degrees, if its off by a few seconds.
I learned an alternative way by selecting both lines and typing the LIST command. The Angle in XY Plane will show the measurement for each segment in bearings, not azimuths. I simply find the difference between the Angles in XY Planes for both lines to determine the angle. I have a few concerns with this method.
1. How do you add subtract bearings measured in degrees, minutes, and seconds? For example, N 76d3'18" W and N 13d56'42"E? I "think" there are websites that can do this? Can this be done directly in AutoCAD through QuickCalc or some other tool?
2. Lines, but not polylines, have Angles in XY Planes in the LIST command. Is this because AutoCAD assumes that polylines will be composed of more than one segment (and each segment with a possible different angle)? Is there anyway to measure the angle of a single one-segment polyline?
Is there a DIFFERENT way between the two methods I just described to measure the angle between two lines (and two polylines) in AutoCAD?
in setting my scale. for example if i hace to draw a box so when i print n measure it reads 5cm x 5cm. how do i enter a scale ?
View 9 Replies View RelatedIs it possible to measure the angle between two faces in 3D?
View 6 Replies View RelatedWhenever we use measure tool it will show the a dialog box with valves of x,y,z, delta X, delta Y & delta Z. I want to customize the same as per the attached image.
Customize this, dialog box will not disappear(modal) after entering into any other command so no need to remember the values of x,y....etc.
I have some users that use Solid Viewer that I am cosidering switching to Inventor LT. I use Inventor Pro. There is a feature in SolidWorks that let's them quickly display the overall extents; length, width, and height for quoting purposes. The tool creates a transparent box around the 3D model and displays these dimensions.
View 6 Replies View RelatedI made a screw that intrudes into a part, but not to the end.
I want to measure the remaining distance, so, i have to select the face of the screw and the hole in the part.
I cannot do that since the program doesn't let me select the faces.
I tried to slice the part with the half section view, but when i press the measure tool the section view ends.
I was recently upgraded from AutoCAD 2005 to AutoCAD 2012. I set my interface to AutoCAD Classic. When I check the Measurement Tools (toolbar) the ribbon appears, but I can not move the toolbar. I run two displays, so the the measure tool shows up on one all the time.
View 2 Replies View RelatedHow do I get Inventor 2009 to measure in degrees and minutes. Below is what I am trying to do.
View 3 Replies View Related