AutoCad 2D :: How To Draw A Coil
Jun 1, 2010how to draw a coiled in 2D drafting. is there any command.
View 8 Replies
ADVERTISEMENT
AutoCad 3D :: Draw Elliptical Coil Spring
Nov 13, 2013I am trying to draw an elliptical coil spring with top and bottom radius of 2 in and center radius of 3 in with 5 turns and spring ht of 5 in. the wire guage is 0.1in.
I could draw a cylindrical spring with helix and sweep command but don't know how to draw an elliptical coil spring. What are the commands or steps to get it. Also, I have problems in getting dimensions of radius and height for the coil spring. I use autocad 2014.
AutoCAD Inventor :: How To Coil A Coil
Jan 14, 2013can we coil a coil in nventor?
If I have a coil or spring, the I want to coil that coil/spring around another axies, can I??
I use Inv.2012
AutoCAD Inventor :: Tapered Coil Drawing
Oct 22, 2013I made a coil with taper. Now I want to make a drawing with that taper, but I don't know how to do that.
View 3 Replies View RelatedAutoCAD Inventor :: Dimension A Spiraled Coil?
Dec 30, 2005I created a simple spiraled coil IV10, and in my IDW I can't place a center mark in the center of the spiral. How do you dimensiom this? I also want to dimension ID and I can't. Something that you would think is so simple is holding me up.
View 9 Replies View RelatedAutoCAD Inventor :: Make A Tapered Coil
Nov 5, 2012Im using Inventor 2013 and im trying to make a tapered coil but instead of creating it with a liner taper i want a curved taper. Is there a way to create this (perhaps using guide curves like loft feature?)
View 9 Replies View RelatedAutoCAD Inventor :: Make A Bent Coil Following Arc 90 Deg?
Jan 26, 2012How the heck do I make a bent coil following an arc 90 deg?
I do know how to make coil and helix, screws etc bur I cannot figure out how to make this coil
AutoCAD Mechanical 2013 (run as vanilla ACAD)
Product Design Suite Ultimate 2013
HP Z800, Dual Xeon W5580, 12 Gb Ram, Windows 7 x64
Nvidia Quadro Fx 4800
Dell M6600 core i7, 16 Gb Ram, Windows 7 x64
Nvidia Quadro M4000
AutoCAD Inventor :: How To Make Hexagonal Coil
Sep 17, 2011I need to make a round coil that rotates along a hexagonal path, so that looking at the coil from the top you see the hexagonal shape.
View 9 Replies View RelatedAutoCAD Inventor :: Can Flat Pattern A Coil
Mar 8, 2013I was wondering if there is any possible way to flat pattern a coil. Attached is a picture of what I am trying to flat pattern. Its a quarter turn of a full coil.
View 7 Replies View RelatedAutoCad 3D :: Creating A Path For Coil Spring?
Jan 9, 2012I'm trying to create a coil spring to go around a long bolt for bracing. I'm using AutoCAD 2011 MEP. I need to know how to make the path for the spring so I can sweep it, it does not have to be super accurate size-wise (it's more for representation purposes) but would still like to know how to do it..
View 3 Replies View RelatedAutoCAD Inventor :: Cut Coil Feature Out Of The Block
May 17, 2012How to cut the coil feature out of the block. I have included the file. I thought the split command would be it but was not able to do anything with it.
View 4 Replies View RelatedAutoCAD Inventor :: Bent Pipe With A Coil Around It
Oct 5, 2011I'm looking for making this part. I'm trying to make a pipe that is bent into a donut so the two ends are connected. Then theres a coil around the pipe.
How I can make the donut and/or the coil?
AutoCAD 2013 :: Model A Coil For Tattoo Machine
Jan 8, 2013I am trying to model a coil for a tattoo machine. I have all of the helixs made to replicate the wire wrapping around the bobbin of the coil but i cannot figure out how to get the helixs to blend together smoothly. I.E. have the end of the inner coil bend outward gradually to meet the starting end of the next level helix.
View 1 Replies View RelatedAutoCAD Inventor :: Coil Around Cylinder Strange Mesh?
Mar 8, 2012Working on a simple cylinder with a coil runing around the outside of it. For some reason the mesh does not handel the geometry correctlly - can figure our why - any thoguths ? Attaced are pics from the meshing and the model.
View 1 Replies View RelatedAutoCAD Inventor :: 2013 Coil Weight Error
Nov 27, 2013Using Inventor 2013 SP1
A user just point out to me that when making a coil with 12 revolution is OK but 13 is really wrong.
tube Ø54x2 mm
Øcoil = 800 mm
pitch = 55 mm
Is there a patch for that?
AutoCAD Inventor :: Coil Or Spring Along A Curved Path
Dec 3, 2010I have a unique part that needs to be generated in IV. It is a sping that follows a curved path (see attachment). I do have complete information, just need to draw it in.
View 8 Replies View RelatedAutoCAD Inventor :: Resemble Shrinking Of A Spring With Coil Command?
Nov 13, 2013I want to insert a spring in an assembly, and for that i will make a spring with the coil command. if i will squeese it between surfaces, will it resemble a spring? will the bindings come closer (i hope they are called bindings, otherwise tell me how they are called)?
View 2 Replies View RelatedAutoCAD Inventor :: 3D Sketch Equation Curve - Creating Coil?
Jul 26, 2013I am trying to create a coil which from above, retains equal and thus parallel pitches whilst at the same time adheres to a semi-circular form in the cross section. You can see from the images attached that the first two revolutions are larger than the semi-circle outline.
These are the values I have used:
Cylindrical
r (t): 134.56924424045517662353735770102mm * t * 0.5
q(t): 1 deg * 360 ul * 3.0 ul * t
z(t): 10 mm * 6 ul * 0.5 ul * t * (1.5 * t) * t
tmin: 0 ul
tmax: 0.916 ul
AutoCAD Inventor :: Create Surface Coil Along Curved Path
Aug 16, 2012I've read the posts pertaining to coil features along curved paths. The existing solutions are limited in that they must rely on a solid with the addition of a bend feature. How can I create a helical surface structure including multiple bends like the one shown?
View 2 Replies View RelatedAutoCAD Inventor :: How To Make Coil Cord Cable Model When It Is Folded
Dec 5, 2012I am trying to make a model of coil cord cable (looks like phone cable) in the autodesk inventor10. I know to make a model of the coil cord when it is straight, but how can i make the coil cord model when it is folder.
View 2 Replies View RelatedAutoCAD Inventor :: Creating Flat Pattern Of A Coil / Spiral Shape?
Sep 25, 2012Is there a way to unfold a coil shape to get the flat pattern? When I try to unfold the attached part I get an error message (see attached error_msg.jpg). We have been using AutoPOL to unfold these kind of shapes (which works fine). But since we have a very old version which we really need to upgrade, I was wondering if nowadays Inventor could handle coil unfolds.
If this will not work with the current IV2013 release, will this then be implemented in a future release? Are there any alternatives or should I just go for the AutoPOL upgrade?
IV2013 Pro SP1
AutoCAD Inventor :: Helical Gear Tooth Profile / Get The Right Helix Angle With Coil Tool?
Dec 8, 2012I have generated a gear set using inventor. Now I would like to 3d print the gears. I have uesd the export tooth shape to get the true tooth profile. now I am attempting to use the coil feature to generate the helical tooth. The problem im running into is in the coil tool I can only give it a Revolution and height dimension. The hight is the width of the gear, but I am having a problem converting the helix angle to the "Revolution" perameter. I have read other posts and they say that it is Helix angle / 360. I have tried that and then compared it to the original gear generated by inventor and it is not even close. I need to do this on in internal gear and match it to an external gear.
View 2 Replies View RelatedPhotoshop :: How To Coil Or Spiral Text
Feb 5, 2004Is it possible to coil or spiral a long piece text using PS?
View 4 Replies View RelatedIllustrator :: How To Make A Spiral Coil
Jan 29, 2014without the "laminated iron core". So what I need to know is how to make those spiral shapes. I tried using some tools but it was pretty hard to do by hand so it actually looked good.
View 15 Replies View Related3ds Max Modeling :: Helical Coil On Curved Spline
Jun 15, 2011I am trying to put a helical coil around a curved spline as shown below. why my image wont upload its only 18k?
View 4 Replies View RelatedAutoCad :: Draw 3D Arc
Jan 4, 2012I want to draw 3d arc using 3d point, how can we draw 3d arc in autocad?
View 4 Replies View RelatedAutoCAD .NET :: Can't Draw Text In New UCS
Dec 15, 2013This is, I tried change new ucs in my autocad by vb.net but when i have new UCS so i can not draw text in this new UCS. This is my
<CommandMethod("ROTZ")> _
Public Sub ShowHatchDialog()
Dim ar As New ArrayList()
[Code].....
AutoCAD .NET :: How To Draw Rectangle
Feb 12, 2013I want to draw a Rectangle in autocad Electrical using VB.net. How to draw?
View 3 Replies View RelatedAutoCAD .NET :: Draw With Object ARX And C#
Jul 31, 2013I have a task to draw a picture(attached in the post) using ObjectARX but the picture is complicated(too many things to take into considerations) and how to accomplish the task. What is the best option. I have to use ObjectARX SDK and C# to do it.
View 5 Replies View RelatedAutoCAD VB :: How To Draw A Spline
Apr 30, 2013I've created four lines and want to spline the end points. Heres my
Public Sub CommandButton4_Click()
Dim pt1 As Variant
Dim pt2 As Variant
Dim pt3 As Variant
Dim pt4 As Variant
Dim pt5 As Variant
[code]....
I get a runtime error - this should be straight forward..
AutoCad :: How To Draw The 2D Curve
Apr 27, 2013How to be able to draw the curve similar with such as the attached image in AutoCAD 2012/2013?
View 9 Replies View Related