I want to insert a spring in an assembly, and for that i will make a spring with the coil command. if i will squeese it between surfaces, will it resemble a spring? will the bindings come closer (i hope they are called bindings, otherwise tell me how they are called)?
View 2 RepliesI have a unique part that needs to be generated in IV. It is a sping that follows a curved path (see attachment). I do have complete information, just need to draw it in.
View 8 Replies View RelatedI am trying to draw an elliptical coil spring with top and bottom radius of 2 in and center radius of 3 in with 5 turns and spring ht of 5 in. the wire guage is 0.1in.
I could draw a cylindrical spring with helix and sweep command but don't know how to draw an elliptical coil spring. What are the commands or steps to get it. Also, I have problems in getting dimensions of radius and height for the coil spring. I use autocad 2014.
I'm trying to create a coil spring to go around a long bolt for bracing. I'm using AutoCAD 2011 MEP. I need to know how to make the path for the spring so I can sweep it, it does not have to be super accurate size-wise (it's more for representation purposes) but would still like to know how to do it..
View 3 Replies View Relatedhow to design and simulate a extension spring (not compression spring) in Autodesk Inventor 2012.
View 5 Replies View Relatedcan we coil a coil in nventor?
If I have a coil or spring, the I want to coil that coil/spring around another axies, can I??
I use Inv.2012
How can I make a part resemble an open cell foam texture using 2013 ?
View 2 Replies View RelatedI made a coil with taper. Now I want to make a drawing with that taper, but I don't know how to do that.
View 3 Replies View RelatedI created a simple spiraled coil IV10, and in my IDW I can't place a center mark in the center of the spiral. How do you dimensiom this? I also want to dimension ID and I can't. Something that you would think is so simple is holding me up.
View 9 Replies View RelatedIm using Inventor 2013 and im trying to make a tapered coil but instead of creating it with a liner taper i want a curved taper. Is there a way to create this (perhaps using guide curves like loft feature?)
View 9 Replies View RelatedHow the heck do I make a bent coil following an arc 90 deg?
I do know how to make coil and helix, screws etc bur I cannot figure out how to make this coil
AutoCAD Mechanical 2013 (run as vanilla ACAD)
Product Design Suite Ultimate 2013
HP Z800, Dual Xeon W5580, 12 Gb Ram, Windows 7 x64
Nvidia Quadro Fx 4800
Dell M6600 core i7, 16 Gb Ram, Windows 7 x64
Nvidia Quadro M4000
I need to make a round coil that rotates along a hexagonal path, so that looking at the coil from the top you see the hexagonal shape.
View 9 Replies View RelatedI was wondering if there is any possible way to flat pattern a coil. Attached is a picture of what I am trying to flat pattern. Its a quarter turn of a full coil.
View 7 Replies View RelatedHow to cut the coil feature out of the block. I have included the file. I thought the split command would be it but was not able to do anything with it.
View 4 Replies View RelatedI'm looking for making this part. I'm trying to make a pipe that is bent into a donut so the two ends are connected. Then theres a coil around the pipe.
How I can make the donut and/or the coil?
How do i get the spring to have a compressed look with flat end....i try different settings but not able to have the spring rings to touch for a compressed look.
View 8 Replies View RelatedI created a spring but when I try to assemble it with constraints it appears to lack a centerline.
View 7 Replies View RelatedWorking on a simple cylinder with a coil runing around the outside of it. For some reason the mesh does not handel the geometry correctlly - can figure our why - any thoguths ? Attaced are pics from the meshing and the model.
View 1 Replies View RelatedUsing Inventor 2013 SP1
A user just point out to me that when making a coil with 12 revolution is OK but 13 is really wrong.
tube Ø54x2 mm
Øcoil = 800 mm
pitch = 55 mm
Is there a patch for that?
I have to make a spring for an engineering class I have yet me nor the teacher know how to make a rectangular spring.
View 3 Replies View RelatedI can't make a spring moving according to other parts' behaviour. I use Inventor 12. by the way I sent two photos (scanned by Microsoft Security Essentials-no problem), the spring in the photos was made by design accelerators-as compression spring. I want from spring to move with the other parts but it doesn't. For instance when I pull the blue part down, blue part, and the spring go the into of each other.
View 3 Replies View RelatedI have cut out a spiral from top on a cylinder, now I want to make a nice finish. And cutting with a conical spring profile is the way to do it.
View 5 Replies View RelatedHow can i draw a SPRING around a circle ? like Attachment picture. (not in the Sketch) in the Part Modeling.
View 1 Replies View RelatedInventor offers us several options to design a coil of constant pitch with a tapering diameter. However, I am unable to create a coil with a taper and a changing pitch at the same time.
We are using Inventor 2013. I would like to produce similar parts as the attached 2D drawings in 3D, only with a changing pitch (distance between revolutions) per revolution. Can it be done? There is software for the CNC spring manufacturing machines to produce such parts. Therefore the proper inputs to produce these effectively and efficiently, are available somewhere.
The part I've been describing uses .09 diameter wire and has about 54 coils in about 8 inches. The starting inside diameter is about .53" and the pitch is about .27" the ending inside diameter is .109" +/- .01 with a pitch of about .091".
Here are 2D drawings of similar parts, the last (NF3) is closest to what we need.
How can i Draw a SPRING around a circle ?
View 3 Replies View RelatedI have a piece of steel that I need to flex. It is a piece of blue tempered spring steel pressed against the corner of a brass pressure transfer. The opposite end of the transfer is tangentlly constrained to a latching mechanism. When the latching mechanism is lifted, the transfer rotates slightly around a screw (made invisible) and the spring is flexed. When the latch is released, the spring returns the latch to the closed position. I have several other assemblies that use the same principal, but some with just a piece of mild steel used as a cover as well as a spring.
View 5 Replies View RelatedIs there a way to create a Coiled spring of 26 coils on an arc radius of 3.781inchs arc length of spring is 13.706inc
The major dia of the spring is 3/8 inch with the wire dia is NOT given
The original Hand done drawing are attached in PDF version 6 format
As for Inventor I'm using 2012. It is the first time I have come across this sort of problem I thought of doing a single coil and creating a sub assemble of it around a construction line arc rad with each coil mated and rotated at an angle to the other but then thought that there must be an easier way of creating this spring.
Inventor 2013 Pro
how can i make each end of the spring flat.How best to cut the end sections so the wire is flat
Invenotr 2012
I use inventor 2011 and i want to create a spring animation. I followed this video step by step but when i constrain the upside and the downside of the spring to those plate objects i get an error.
this is the video i followed:
[URL].....
I cant seem to find out how to assemble the spring to the rest of my item.
Will you be able to use the assembly if I do not provide the parts used(maximum 3 uploads)?
I am trying to create a coil which from above, retains equal and thus parallel pitches whilst at the same time adheres to a semi-circular form in the cross section. You can see from the images attached that the first two revolutions are larger than the semi-circle outline.
These are the values I have used:
Cylindrical
r (t): 134.56924424045517662353735770102mm * t * 0.5
q(t): 1 deg * 360 ul * 3.0 ul * t
z(t): 10 mm * 6 ul * 0.5 ul * t * (1.5 * t) * t
tmin: 0 ul
tmax: 0.916 ul