When I use the copy tool, not copy and paste, the object that I copy doesn't show up. I click on an object click the copy took then click in the location where I want the new object, nothing shows up. Then if I save the drawing, close and reopen it, the object will be show up in the new location. It sometimes happens with move and rotate. I'm using 2013 64 bit version on Windows 7.
View 2 RepliesI have a rounded rectangle and an object on top of it -- how do I make it so that the parts of the object outside of the rounded rectangle are hidden?
View 5 Replies View RelatedWhen we copy multileadered items from one viewport to another the leaders do not show up, but the text does.
View 3 Replies View RelatedI have created some new commands (that basically reference some lisp routines we have on our network) and would now like to copy these files to our other users...I knew which files to copy when we were working in LDD (the .mns files) but what files I need to copy to the other users PC's...the new commands all work and they are all in the quick access toolbar..
View 1 Replies View RelatedI have recently upgraded to AutoCAD LT 2012. The copy/paste function and the group/ungroup function are not working. I have run service pack 2 with no improvement.
View 9 Replies View RelatedWithin drawing and between drawing copy with basepoint and paste is not working anymore.
View 9 Replies View RelatedStill getting used to the new versions of AutoCAD, I'm using AutoCAD 2012 Lt version.
So my problem is, I want to copy something from one drawing and paste it into another drawing, however, when I copy over my lines/polylines etc, it comes into the new drawing as one straight line, I assume it is in some other orthographic projection to my current drawing, and I don't know how to change it (rotate it?) to suit the current drawing....
I regularly use CTL-C & CTL-V to move objects from one drawing to another. That is I used to but now it's broken. When I select objects and use CTL-C, the command line says "_copyclip x found" (where "x" is the number of objects). I then go to another drawing and use CTL-V whereupon the command line says "_pasteclip" but I get no opportunity to select a base point and nothing more happens. I found a string describing this exact problem and a member suggested a "HotFix" of file "acdb17.dll" I searched my ACAD install folder and found no such file. I searched the entire hard drive and didn't find it. I put the supposed magic file in my ACAD folder (along with all the other dll files), re-started AutoCAD and still I can't use windows copy and paste. These commands work as expected in all other programs, just not Auto CAD. It's not that I'm married to the clipboard but I really need to move objects from one drawing to another. I also tried first saving all objects as a block but that didn't work. I've read where this problem exists in 2007 but I used to use 2007 with no problem. I'm on 2002 now and it used to work on that too.
View 4 Replies View RelatedI have object data attached to some linework and I want to copy that data to some new entities.Is it possible to copy object data from one entity to another with out having to fill in the table again.
View 3 Replies View Relatedso i have a file that when i zoom extents i can not see or select anything by window but when i use the command erase all is says there are 42 objects in the file but i cant find them
rename attached file ext to dwg
I recently installed Inventor 2014. With Inventor 2013, I was able to do a Save Copy As on an IDW file to save it as either a DXF file or AutoCAD DWG file without any issues. In Inventor 2014, doing this produces the following dialog boxes in succession:
No DXF or DWG is produced. I tried doing this to a new, blank drawing from one of the default IDW templates and I get the same result. What can I do to fix this?
A few of the computers are having problems with the Copy/Paste function. They had it working a few times and after that, it stopped working (can't paste after copying). Have tried restarting autocad and the computer but the issue is still there. Have also tried updating the service pack to the latest version. It works for a while and stopped working again.
View 5 Replies View RelatedWhen I try to copy and pate any element within the same drawing it won´t paste it will say: "specify insertion point" and I´ve given up.
I tried PICKFIRST but it is set to 1, also tried checking if it would fit in my screen or if the zoom was messed up, but nothing works!
I am using ACAD 2000. My wblock and copyclip commands are not working only in one specific drawing. I am working in modelspace.
When I wblock it lets me select the objects and assign a file to save the objects to. When I hit OK it gives me no error but no file is created.
When I copyclip it gives me no error, but when I pasteclip, nothing happens.
I tried saving the drawing as something else. This drawing simply won't let me copyclip or wblock. I can use the copy command to make multiple copies of the object in question within the drawing. I tried restarting my PC and this particular drawing still has the same problem. Other drawings are fine.
"save copy as" is no longer working as is "save as", what happened?
View 7 Replies View RelatedI have a project for school that I am trying to complete at home, but realized that I don't have the proper SUD file at home. Is there any way I could copy and paste the already dimensioned object into the new SUD later?
View 1 Replies View RelatedI'm using AutoCad LT 2013 at work. My issue is I have always been able to highlight and object and then enter my command and perform that command. Something happened and now when I highlight then enter my command and press enter it un-highlights the object and prompts me to highlight the object again. Also if I want to copy and paste a highlighted object it wont allow me unless I type in the command first. I can't figure out what I did.
View 4 Replies View RelatedI have a map of an island. I am trying to copy and object say a block or triangle into the certain areas of the island several times. How can i do this using the command.
View 4 Replies View RelatedI am using windows 7 and I installed photoshop cs6 extended.after I installed it, copy css doesn't show up on the right click panel.I've just searched for the update for extended. But update only available on Macintosh.
View 1 Replies View RelatedI use net to select an object,and highlight it. but the control point couldn't be shown!
View 3 Replies View Relatedhow I can use VBA to select objects in the drawing, so that the grips are enabled/shown. The editing of the object will be done manually in AutoCAD. All I want for VBA to do, is to select them.
View 6 Replies View Relatedthere is a way to show or hide a specific object (not the layer it is sitting in) in a specified viewport without affecting its visibility in model space or other viewports. I came across a .vlx file from www.cadstudio.cz/dl./hideshow.vlx that does the job of showing or hiding an object in model space( and hence in all viewports).
View 5 Replies View RelatedI wrote a program that I can give a name automaticly for all 3d solid objects.
But I want to show a little box on isometric view every names with VBA codes.
How can I show 3D Solid object's name on isometric view?
I try to show on Attachment.
If I am copying an object using snaps vertically down a wall a certain distance and come to a wall corner and then need to copy the object the same distance horizontally as I did vertically is there an easy way to enter this new direction? I keep thinking that I would just enter displacement and for X I should be able to use my mouse and snap/measure the old Y distance and then put Y,Z as 0. However, there is no option to get a relative distance in displacement. Is there something I am missing in the command?
View 8 Replies View RelatedIs there anyway to copy an alignment from one drawing to another?I want to copy the alignment but not have it come in as a alignment just an object line
I don't want to spend the time drawing a PL over the top of it (its a very complex) then copying that.
The assembly in the attached files was working fine in 2011, then for some reason it stopped updating. So I opened and saved in 2012 and it still doesnt update.
Open the assembly, edit the extrusion in Copy Surface Master and change the distance to 500. You can see that the copied faces do not update in the other parts, but there are no error warnings.
I logged with my VAR and they said use derive instead and closed the ticket. Sure derive is another way but copy object with associativity should work so this is my way of bringing to autodesks attention.
I am attempting to copy and paste a part of a drawing from AutoCAD 2011 into ms, Excel or Word. I am able to copy within a vport so my whole screen is not copied. My problem is only 2D objects show up when I paste. I tried different visual styles and colors but still cant get my solid objects to appear.
View 7 Replies View RelatedWhen I try to Copy & Paste an object from one file to another, appears following alert window: “This application has detected a mixed version of AEC objects participating in this operation. Newer AEC objects will be disallowed from participating in this operation”. And I cannot paste the object copied from other file. This happened to me when I work with Autocad2010 using drawings saved as Autocad2004 in Autocad2013.
Since I am working in a group of people that have different versions of Autocad, I need the solution for this problem.
If I drag an effect from the target circle of one object to anther in the layer's panel it replaces the effect along with all appearance. But I want just to add the effect. For example, a layer has a drop shadow and a path, round corners. I want to move the drop shadow from the layer to the path so that the path now has the round corners and the drop shadow. To do this I have to open the shadow effect of the layer wright down its parameters, then create a shadow effect for the path with the same parameters which is a lot of work.
View 3 Replies View RelatedHow to expand the Quick Properties Tool? show that it will show lineweight and more stuff (See Pic), some drawing that i work with Quick properties show more features, but this drawing doesn't.
QOJ.JPG
Trying to find out how to copy an object multiple times in a curve. I've used microstation and it does it easily and just wandering is AC has the same type funtion without going throught 6-8 steps for each copy.
View 9 Replies View Related